How to install a satellite dish to achieve a pot of Samsung reception, is Zhongxing 6B, Yazhou 3S an

It is best to be a pot of more than one meter and five The main head receives the middle star six b (after the middle six b is adjusted, fix the pot and add the two heads of the partial collection) The head of the person facing the pot is on the left side of the main head, that is, the west is about six or seven centimeters away from the main head (depending on the caliber of the pot, it will be slightly closer or a little farther away) The third head is on the right side of the main head, that is, the east Probably this distance is also this distance The third TVB8 group is not easy to tune The other groups are no problem Then connect it with a four-cut switch and set the corresponding parameters on the receiver PS: Don't connect any switch when you tune the star, because the signal is attenuated after the switch, I wish you success.

Selection of equipment. Pots, feeders, high-frequency heads, receivers. The first is the selection of pots, most of the integrated pots on the market are rice, and if possible, you can choose a pot with a larger caliber. The feeder is generally not very good in quality, and the interface is easy to slip off, break, and break.

Therefore, it is best to choose a feeder with multiple shielding layers, as well as a stainless steel interface and then Sou Zhenmeng is a high-frequency head, this is very critical, it is related to the quality of the program, most of the high-frequency heads on the market are kaide, the quality is average, but it is more than enough to see the middle six! Then there are receivers, with famous brands such as Haier, Hisense, and Changhong.

But usually use a receiver of about 100 yuan, Kehai 2830 is good. Of course, don't buy anything that is too rough. The assembly of equipment is very important for the installation of the pot, some people seem to have put the pot together, but the signal quality cannot be improved.

This should pay attention to the position of the three struts and the feed disc, when installing, be sure to make the feed disc in the center of the pot, the inclination of the three rods should be consistent, and it is best to make the round surface of the feed disc roughly parallel to the round surface of the pot.

Don't be too far away, the installation of the high-frequency head, the middle six high frequency head has a polarization angle, which is more troublesome than the middle nine high frequency head, even if it is a small degree (polarization angle), which has a great impact on the signal.

First, insert the high-frequency head into the feed disc, so that the lower end is exposed to the disc 1-2 cm, facing the cauldron, so that the horizontal polarization arrow is horizontally to the left, and then turn the high-frequency head clockwise 8-10 degrees, and fix the high-frequency head with screws.

First of all, you need to install all the equipment correctly.

Press the information key on the remote control.

Zhongxing 6b is based on Fujian Southeast Satellite TV as the standard.

You adjust the angle of the lid slightly, and at the same time pay attention to the signal quality strength bar; You can refer to the approximate location of other people's homes, and then move them, you think of the satellite as the sun, and then your pot moves slowly, and it is recommended that you fix the height first, and then move it left and right, be slow, be patient, if you don't, then you want to fine-tune the height up or down, and the amplitude should not be too large.

When you receive Fujian Southeast Satellite TV, it will enter the fine-tuning period, first of all, Inner Mongolia Satellite TV, Shanxi Satellite TV, Chongqing Satellite TV, Hunan Satellite TV, Qinghai Satellite TV, China Meteorological Channel, these stations with slightly weaker signal strength. If you can't find it, just adjust the signal strength of the China Meteorological Channel to more than 20%.

The last step is the high-frequency head, and this is the most critical one, and the high-frequency head is offset by one centimeter, and maybe you will lose more than 10 units. The specific method is to first adjust to the peak with ** as the standard. And then let's take a look at the stations I mentioned above.

If you have all of them, then the other stations should be fine.

I'm just telling you the way I usually install it for others, and I hope it helps.

In addition, the city is not allowed to put pots, I hope you understand.

I'm here to ask you! There are a lot of ** devices on the satellite, and one ** device is used for a set of parameters! Some of the ** device transmit power, and some have weak signals due to aging and other reasons!

Therefore, some programs have good signals, and some programs have poor signals! It also has to do with the weather! If it rains, the signal will be even weaker!

You can press the information button of the remote control to check the signal quality of each group of ** devices and compare them.

Simple, buy a 22k switch, generally not more than 10 yuan. Tell you how to connect:

Both lids should be adjusted to have a signal.

Connect the 22K switch, and connect the "on" interface of Zhongxing 6B. Asia 3S is connected to the "OFF" interface.

The key point above is that before connecting 22k, adjust both lids to have a signal, and it is very troublesome to adjust the signal if you connect to 22k.

You use 2 pot lids, you can also use a pot lid to collect these 2 stars, the minimum diameter of the pot lid should be in meters, but there are no 2 good effects, but a pot lid takes up less space, each has its own benefits, I use a pot lid with a diameter of meters to receive 6 satellite signals, you don't know what you can continue to ask.

Congratulations on your success!

Press the cauldron to receive the star 6b, please know the latitude and longitude of your location before pressing the potThen turn on the receiver, go to the menu - system settings - star guidance - press the confirm button and enter the longitude (as well as the latitude and longitude of your location) into the machine according to the prompts to watch the satellite 6b. It will calculate the azimuth and elevation angles in no time.

The noodles should be horizontal. Place the flat edge of the bottom of the measuring instrument against the bottom of the wooden strip. Adjust the elevation of the pot to the elevation angle calculated by the machine.

Then turn on the receiver and tune a pre-stored program casually, press the information button, and then adjust the pot and high-frequency head until you see that there is no mosaic in the program. Try to adjust the signal quality to the value, fix the pot and the high-frequency head. If there are no program parameters in the receiver, please open the menu to adjust to the program settings - add program - enter the program parameters (local oscillator frequency, downlink frequency, symbol rate, polarization mode) and then adjust the pot left and right.

And fine-tune the elevation angle and high-frequency head, fix the pot and high-frequency head when the signal strength and signal quality are the maximum value, and then press the confirm button to manually or automatically search for the program. The zero degree line of the high-frequency head should be parallel to the ground.

Midstar 6b is over the equator at 115 degrees east longitude. You can check the longitude of your home on the computer to know the approximate location of the antenna. Then watch TV. Slowly move the antenna orientation to find the signal. Easy to find.

The pot is a little small, if you only look at the two groups of Phoenix and Sunshine, the problem is not big, and it is difficult for the group of Huayu to accept it,

Twist the antenna 10° to the west and aim it at Asia 3S; Received Phoenix Satellite TV 4000 h 26850 and other channels, and tightened the antenna position; Then use a C-band high-frequency head with a 5150 internal oscillator, place it about the west of the main high-frequency head, receive the Zhongxing 6B signal, and fasten the high-frequency head; The two high-frequency heads are connected in parallel with a 22kHz relay switch, one star is connected to 0kHz, and the other star is connected to 22kHz, remember that the machine sets the star connected to 0 to set 22kHz "off", and the star connected to 22kHz is "on", and the machine will automatically switch with the channel conversion; It's just that the antenna is a little small, and it won't be able to be collected in rain and snow, so it's fine.

install a double circle on the cauldron; Adjust Zhongxing 6B first; Do not move the pot at this time; Use another high-frequency head to tune the Asian 3s;

A satellite receiver can receive signals from Zhongxing-6B and Xinnuo-3 satellites at the same time, and it can be changed to a pot of double satellites. One pot of two satellites means that a satellite antenna is equipped with two high-frequency heads, which can receive signals from two different satellites at the same time, but the receiver box must support two or more high-frequency head interfaces.

The prerequisites are as follows:

1. The calculation object is the forward feed antenna, and a satellite is determined as the main focus.

2. Look at the antenna focal distance (the distance between the center point of the antenna and the receiving point).

3. Have local azimuth and elevation data for the two satellites (which can be found from the satellite parameter calculation**).

Calculation method: set the azimuth difference between the two satellites to a, the elevation difference to b, the antenna focal length to l, and the distance between the two high-frequency head receiving points to x.

Don't add a high-frequency head, nothing is needed, Zhongxing 6b itself can accept the signal of Xinnuo No. 3, just turn the lid in the opposite direction, the angle is due south as the center, generally 6b is due south to the west Xinnuo No. 3 is due south to east, Xinnuo can only see 12 units, the rest are charged, 6b can see forty-six.

One is aligned with Xinnuo No. 3, and the other is aligned with Zhongxing 6b plus a 22k connector for about ten yuan After alignment, when the set-top box is set, select 22k when the device is on, search the platform once, select the time when it is off, and search the platform once If the set-top box is preset, then just connect the connector correctly If you don't know, you can try the two joints twice.