What are the steps to use the line number machine? How to use the line number machine and the coding

Although the brand and grade of the line number machine on the market are different, the basic operation methods are similar, which is nothing more than two operation methods, 1: stand-alone printing; 2: Online printing.

Shuofang line number machine is the brand line number machine with the largest number of shares in the market, and the following is a detailed introduction to Shuofang line number machine as an example:

1. Stand-alone printing method:

1. After receiving the line number machine, please put the machine in a flat place.

2. Open the upper cover of the wire number machine and tear off the tape on the half-cutting knife so as not to affect the normal cutting of the half-cutting knife.

3. If it is a printed sticker, please pull out the sticker so that the sticker is 2cm lower than the position of the half-cutter;

Turn left|Turn right.

4. If it is a printing sleeve, please take out the sticker and pass the sleeve through the sleeve adjuster. After installing the adjuster, make the casing beyond the position of the half-cutter.

5. After installing the sleeve, put the ribbon box into it, and rotate the knob on the right side of the ribbon box to 12 o'clock.

At this point, the ribbon and sleeve or sticker have been installed, and the corresponding materials and input text can be printed on the machine.

S&R T800, T900, C-180E, C-180T line number machine printing casing single machine operation method: Prepare a wire number machine, ribbon, casing, casing bracket; First, tighten the ribbon in the direction of the arrow around the hole on the left side of the ribbon, install the ribbon on the machine, let the two holes of the ribbon be set on the two blue pillars on the machine, and lay the ribbon flat; , the casing is placed on the casing bracket, the head of the casing is placed in the machine, the head should exceed the half-cutting knife, the casing passes the casing adjustment knob, the casing is flattened, the blue knob on the right side is tightened, the tube is S-shaped, and the Sai N Ruide line machine does not need a casing adjuster (see figure); The line number machine is turned on, select the casing specification, please select the casing pipe for the casing below 2 squares, please select the casing for the casing above 4 square meters, please select the casing pipe 6 for the casing between 2-4, and select the casing 4 for the casing between 2-4, press enter, and set the attributes such as section length, font size, number of repetitions, half-cutting, character scaling, etc.; , enter the content to be printed, press enter after entering a piece of content, continue to enter a piece of content, press enter again until all the content is entered, press the file key, save the file in case of loss; If there is a setting that needs to be modified, press the cancel key to pause, then press any key to return, press the up arrow all the time, move the cursor to the first line, reset the paragraph length, font size and other information, and press the file key again to save; When the ribbon is exhausted and the new ribbon is replaced, the machine will automatically prompt the breakpoint printing (whether to continue printing); T800, T900 line number machine when the casing is about to run out, press the cancel button to pause, after replacing the new casing, only press the print button, the display screen prompts printing or breakpoint printing, select breakpoint printing, press enter, the machine will continue to print the content that has not been finished just now.

The use of the line number machine coding machine is as follows: 1. Install the ribbon and the number pipe cavity such as (sticker).

Attach the ribbon and number tube (sticker) to the line printer.

2. Install the casing and casing adjuster.

Install the number tube to the casing naughty restitter.

3. Cover the shell of the online number machine.

Due to the fact that the line number machine will be run with a cutter when it is running, in order to be safe, the safety shell needs to be covered, otherwise the line number machine will not work.

4. Plug in and turn on.

Connect the line number machine to the power supply and turn on the power switch of the boat.

5. Material setting.

Set up the roller according to the material to be printed.

6. Print the content, and the content that needs to be printed.

7. Officially print, and complete the printing of the number tube.

A wire number printer is a device used to print words and numbers on a variety of products. They are often used in the packaging industry to identify and distinguish different products. The use of the wire number machine coder is relatively simple, it only requires connecting the device to a power source and loading the appropriate ink or ink.

Once the preparation is complete, the information to be printed is entered into the control panel of the printer. This information can be a product name, number, date, or other identifier. Once the information has been entered, the coder is ready to work.

Place the product on the conveyor belt under the coder and press the print button. The coder quickly prints the required information and pushes the product off the conveyor belt so that the next product can be printed.

Wire number printers typically have high-speed printing capabilities and high reliability. They can handle large quantities of products in a short period of time and ensure that each product is clearly and accurately marked. This makes them an important tool in the packaging and logistics industry.

In addition, wire number printers usually have adjustable print positions and font sizes. This makes them suitable for a wide range of products of different sizes and shapes, from small bottles to large boxes. Many printers also have an automatic cleaning feature to ensure that the equipment is always in top condition.

Although the use of the old coding machine is very simple, it needs to be properly trained and guided before use. This will ensure that the operator understands how the equipment works and knows how to take appropriate action if something goes wrong with the equipment. In addition, the use of the coder also needs to comply with relevant safety and environmental standards to ensure the safety and longevity of the equipment.

In conclusion, the wire number printer is an efficient, reliable and suitable equipment for a wide range of products. They are very useful in the packaging and logistics industry to quickly and accurately identify and distinguish between different products. With proper training and safety instruction, operators can safely use the coder and ensure that the equipment is always in top condition.

S&R T800, T900, C-180E, C-180T line number machine printing casing single machine operation method: Prepare a wire number machine, ribbon, casing, casing bracket; First, tighten the ribbon in the direction of the arrow around the hole on the left side of the ribbon, install the ribbon on the machine, let the two holes of the ribbon be set on the two blue pillars on the machine, and lay the ribbon flat; , the casing is placed on the casing bracket, the head of the casing is placed in the machine, the head should exceed the half-cutting knife, the casing passes the casing adjustment knob, the casing is flattened, the blue knob on the right side is tightened, the tube is S-shaped, and the Sai N Ruide line machine does not need a casing adjuster (see figure); The line number machine is turned on, select the casing specification, please select the casing pipe for the casing below 2 squares, please select the casing for the casing above 4 square meters, please select the casing pipe 6 for the casing between 2-4, and select the casing 4 for the casing between 2-4, press enter, and set the attributes such as section length, font size, number of repetitions, half-cutting, character scaling, etc.; , enter the content to be printed, press enter after entering a piece of content, continue to enter a piece of content, press enter again until all the content is entered, press the file key, save the file in case of loss; If there is a setting that needs to be modified, press the cancel key to pause, then press any key to return, press the up arrow all the time, move the cursor to the first line, reset the paragraph length, font size and other information, and press the file key again to save; When the ribbon is exhausted and the new ribbon is replaced, the machine will automatically prompt the breakpoint printing (whether to continue printing); T800, T900 line number machine when the casing is about to run out, press the cancel button to pause, after replacing the new casing, only press the print button, the display screen prompts printing or breakpoint printing, select breakpoint printing, press enter, the machine will continue to print the content that has not been finished just now.

Different brands of line number machines are similar in how to use, nothing more than the following steps:

2.Install the ribbon: check whether the ribbon part exposed by the ribbon of the wire number machine is flat and compact, if not, rotate the front axis of the ribbon with your fingers and tighten the ribbon; Open the upper cover of the wire machine, the position of the ribbon of the corresponding model of the wire machine, install the ribbon, and if the installation is correct, you will hear a "click", and the ribbon will be in place accurately.

3.Install the casing: Insert the casing from the left only through the casing adjuster, the front end of the casing is exposed by 2cm, and install the casing adjuster corresponding to the position of the casing adjuster, and you will hear a "click" sound when it is in place.

4.Printing: Whether it is a stand-alone version or an online version of the line number machine has its own keyboard, there are function keys on the keyboard, after entering the content that needs to be entered, the corresponding function function key, simply decorate, and then preview, print.

5.Online Operation: Required**, install software and drivers. Go to the official website of the brand** driver and software for the corresponding line number machine model, and after installation, you can use the content, preview, and print on the software.

If you have any questions, you can log in to the official ** of Shuofang Technology to find customer service consultation.

The brand is different, the operation process is also different, and it can only be explained in a targeted manner.

S&R T800, T900, C-180E, C-180T line number machine printing casing single machine operation method: Prepare a wire number machine, ribbon, casing, casing bracket; First, tighten the ribbon in the direction of the arrow around the hole on the left side of the ribbon, install the ribbon on the machine, let the two holes of the ribbon be set on the two blue pillars on the machine, and lay the ribbon flat; , the casing is placed on the casing bracket, the head of the casing is placed in the machine, the head should exceed the half-cutting knife, the casing passes the casing adjustment knob, the casing is flattened, the blue knob on the right side is tightened, the tube is S-shaped, and the Sai N Ruide line machine does not need a casing adjuster (see figure); The line number machine is turned on, select the casing specification, please select the casing pipe for the casing below 2 squares, please select the casing for the casing above 4 square meters, please select the casing pipe 6 for the casing between 2-4, and select the casing 4 for the casing between 2-4, press enter, and set the attributes such as section length, font size, number of repetitions, half-cutting, character scaling, etc.; , enter the content to be printed, press enter after entering a piece of content, continue to enter a piece of content, press enter again until all the content is entered, press the file key, save the file in case of loss; If there is a setting that needs to be modified, press the cancel key to pause, then press any key to return, press the up arrow all the time, move the cursor to the first line, reset the paragraph length, font size and other information, and press the file key again to save; When the ribbon is exhausted and the new ribbon is replaced, the machine will automatically prompt the breakpoint printing (whether to continue printing); T800, T900 line number machine when the casing is about to run out, press the cancel button to pause, after replacing the new casing, only press the print button, the display screen prompts printing or breakpoint printing, select breakpoint printing, press enter, the machine will continue to print the content that has not been finished just now.

How to use the line number machine.

3. All this kind of printing line number machine is called line number machine, the full name is line number printing machine, line number printer, referred to as line number machine, marking machine, coding machine, rubber head machine. It is generally used for electronic control, power distribution equipment identification, secondary circuit wire wiring identification, cable fiber optic cable identification, wiring harness identification, high and low voltage switchgear terminal head printing, etc., and is a special equipment for electronic control, power distribution equipment and integrated wiring engineering wiring identification, which can meet the needs of power plants, electrical equipment factories, substations, and power industry wire identification marks.

Shuofang TP76i line number machine.

The machine that makes the line number is called the line number machine.

The wire number machine can be printed on PVC casing, heat shrinkable sleeve, self-adhesive label paper Chinese characters, numbers, foreign languages, **, power symbols, etc., mainly used for identification, widely used in electric power, mechanical automation, integrated wiring, security, rail transit, new energy and other fields, for various specifications of wire, switches, control cabinets have a very mature identification solutions.

Line number machine, can also be called line number printer, number tube printer, heat shrinkable tube printer or sleeve printer, there are several domestic line number machine brands with a history of more than ten years on the market, the choice of line number machine to consider the following aspects: 1, the amount of printing, if the amount is small, choose the domestic T800 line number machine; If the printing volume is large, it is best to choose a T900 line number machine that can be connected to a computer; 2. The type of consumables to be printed, if the types of printed tubes are more miscellaneous, there are both PVC sleeves and various specifications of heat shrinkable tubes, and the printing range is relatively wide, such as squared, to consider the compatibility of the machine and the printing range, it is best to choose a C-180E line number machine can be played well; 3. For the durability of the machine, we must choose a machine with durable leather and long warranty period; On the whole, it is recommended that you choose the line number machine of Enred C-180T.

Line number machine application.

The thirteenth episode, Qin Keqing died and sealed the dragon and banned the lieutenant, Wang Xifeng assisted Ning Guofu.

This is related to your use case, the line number machine can realize the printing of the sleeve and the printing of the label according to the function, and the sleeve and label are the consumable materials you need;

At present, the wire number machine is printed by heat transfer, and the ribbon is disposable, which is basically 1:1 length with the printing material.

So the daily consumables are sleeves, labels and ribbons.

Of course, there are many specifications of casing (square - 10 square), and stickers are also divided into three specifications. Just choose according to your use case.

If you still have any questions, please feel free to contact us.