How to solve the problem that the floor heating of the faroli wall hung boiler is not hot?

Updated on home 2024-03-05
10 answers
  1. Anonymous users2024-02-06

    1. First check the switch of the floor heating. If the floor heating rod is found to be hot and the return bar is not hot, it is an indication that there is gas in the pipes, which causes hot water to enter the circuit and circulate. Solution: It's as simple as opening the exhaust valve on the water separator directly until the hot water flows out.

    2. If the floor of the house is too high, or the house is at the end of the heating of the house in the community, the pressure of the pipe is not high, which will also lead to poor heating effect.

    Solution: If this happens, the first thing to do is to find a property or heating company to solve it. If not, consider installing a circulating pump to improve the circulation of hot water to achieve the desired heating effect.

    3. If the main water supply pipe is not hot, it may be because the water quality is too poor or too dirty, which makes the filter clogged and affects the normal circulation of the system.

    Solution: First close the water supply valve and return valve, then open the filter with a movable wrench to clean the internal filter, and finally install it back. If you're afraid that you won't be able to break the filter, you can get a professional to clean the filter.

  2. Anonymous users2024-02-05

    Faroli wall-hung boiler E3 thermostat failure: 1. Blockage of the waterway Clear the blockage of the waterway Open the exhaust valve of the water pump and the exhaust valve of the pipeline to exhaust.

    2. The pump does not rotate or is abnormal a. Check whether the pump is stuck If it is stuck, turn the front screw of the pump motor back and forth.

    b. Use a multimeter to measure whether there is a 220V voltage between the connecting terminals of the water pump of the motherboard.

    3. If the thermostat is faulty, put the multimeter in the on-off gear and measure the two ports of the thermostat If it is in the connected state, the thermostat is normal, otherwise replace the thermostat.

    4. If the connecting line is broken or the connector is not connected, use a multimeter to measure whether the connecting line is intact and connect the connector.

    5. The main control board is damaged.

  3. Anonymous users2024-02-04

    Reasons and treatment methods for wall-hung boiler floor heating is not hot:

    1. The length of the floor heating pipe coil is too long. If you plan to install a wall-hung boiler and negotiate with the floor heating installation company in advance, it is recommended that each pipe is required to be about 60 meters, if it is too long, it will indirectly increase the heating effect, and the indoor heating is too slow and the heat is not hot.

    2. The backfill layer is too thick. It is suggested that on the basis of energy saving and environmental protection, the backfill of the wall-hung boiler should be controlled within 4 cm, so that a certain amount of heat can be achieved.

    3. The supervisor walks too long and the water flow is too slow. The so-called length is to reduce the pressure and also lose heat, so it is recommended that the wall-hung boiler should be closer to the collector of the floor heating water distributor, so that the hot water can be sent to the floor heating immediately.

  4. Anonymous users2024-02-03

    Summary. Hello dear, here's how. 1. Long heating time, which leads to the occurrence of non-heating phenomenon.

    2. If the heating rod is broken, the hot water cannot be heated, resulting in the appearance of no heat (warranty required). 3. If the circuit fails, it will also lead to the inability to heat cold water (warranty required). 4. Due to the blockage of the gas path, the Vaillant wall-hung boiler cannot be heated.

    5. If the temperature controller is broken, this will also cause the wall-hung boiler to not be heated, just replace the thermostat (warranty required).

    Hello dear, here's how. 1. Long heating time, which leads to the occurrence of non-heating phenomenon. 2. If the heating rod is broken, the hot water cannot be heated, resulting in the appearance of no heat (the manuscript needs to be repaired).

    3. If the circuit fails, it will also lead to the inability to heat cold water (warranty required). 4. Due to the blockage of the gas path, the Vaillant wall-hung boiler cannot be heated. 5. If the temperature controller is broken, this will also cause the wall-hung boiler to not be heated, just delay the argument and change the thermostat (warranty required).

    Dear, I hope the above methods can help you <>

  5. Anonymous users2024-02-02

    Summary. You can first try to recharge the gas meter, open the gas valve, and replace the gas meter battery. If you still can't get gas, contact your gas company or property for repairs.

    The second reason may be that the ignition electrode and flame induction electrode inside the wall-hung boiler have serious carbon deposits. Most of this factor is due to the lack of maintenance of wall-hung boilers. The water pressure of the wall-hung boiler system is too low, and water needs to be replenished

    You first find the water replenishment switch at the bottom of the wall-hung boiler, turn it on counterclockwise to the left, observe the water pressure gauge pointer, when the water pressure rises to the left and right, turn off the water replenishment switch clockwise to the right, remember to turn off the water replenishment switch tightly to avoid system pressure relief and water leakage, if the machine is not started, please re-use. The wall-hung boiler does not heat because the thermostat command or the solenoid valve is faulty, if the pressure indication is below the kilogram, it means that the water pressure is low. The solution is to find the water supply nozzle and connect the pipe to increase the water pressure to kilograms; Then, disconnect the power supply and start from scratch on it.

    I'm sorry I don't understand, but can you elaborate on that?

    You can first try to recharge the gas meter, open the gas valve, and replace the battery of the gas meter. If you still can't get gas, contact your gas company or property for repairs. The second reason may be that the ignition electrode and flame induction electrode inside the wall-hung boiler have serious carbon deposits.

    Most of this factor is due to the lack of maintenance of wall-hung boilers. The water pressure of the wall-hung boiler system is too low, you need to replenish water, the water replenishment method is divided: you first find the water replenishment switch at the bottom of the wall-hung boiler, turn it on counterclockwise to the left, observe the water pressure gauge pointer, when the water pressure rises to the left and right, close the water replenishment switch clockwise to the right, remember to close the water replenishment switch tightly to avoid system pressure relief and water leakage, if the machine is not started, please re-use.

    The wall-hung boiler does not heat because the thermostat command or the solenoid valve is faulty, if the pressure indication is below the kilogram, it means that the water pressure is low. The solution is to find the water replenishment nozzle and connect the pipe, and increase the water pressure to kilograms; Then, disconnect the power supply and start from scratch on it. More about the wall-hung stove does not burn the heating what's wrong, enter:

    https...

  6. Anonymous users2024-02-01

    Summary. If the wall-hung boiler is used for a long time, it is easy to be corroded by gas, and then it swells, so it is necessary to replace the parts. 2.

    Water pressure problem, when the water pressure is too low, the wall-hung boiler often cannot be used normally, and if the blocked water cannot flow normally, this fault will also occur. Solution: At this time, just clean it up3

    If the water cannot flow normally due to the blockage of the filter at the water inlet, it can be cleaned up.

    If the wall-hung boiler is used for a long time, it is easy to be corroded by gas, and then it swells, so it is necessary to replace the parts. 2.Water pressure problem, when the water pressure is too low, the wall-hung boiler often cannot be used normally, if it causes a blockage of the water socks can not flow normally, Lahao Zai will also have this fault.

    Solution: At this time, just clean it up3If the water cannot flow normally due to the blockage of the filter at the water inlet, it can be cleaned up.

    Can you add, I don't quite understand it.

    If the water cannot flow normally due to the blockage of the filter at the water inlet, it can be cleaned up. 4.If there is a problem with the local penetration of the induction porcelain needle or the ignition porcelain needle, there will be no ignition sound and electric spark.

    Solution: If it is the aging of the induction porcelain needle, polish it and put it carefully and can be ignited normally, if the ignition needle is offset or aging, it needs to be placed correctly or replaced. 5.

    If the use time is too long, it will cause the pipeline to scale and cause blockage.

  7. Anonymous users2024-01-31

    The Faroli wall-hung boiler is a commonly used heating device that can be used to keep the room warm and comfortable during the cold winter. However, if there is a failure, it will not only affect the heating effect, but also may bring certain safety hazards to the user. Below, I will introduce some common faults of Faroli wall-hung boilers and their solutions.

    1.Start-up failure: If the button cannot be started when the Faroli wall-hung boiler is turned on, it may be caused by power failure, poor wire contact, control board failure, safety door failure and other reasons.

    The solution is to check that the power supply, wires, and control board are working properly, and to make sure the safety door is closed.

    2.Fireless fault: If the Faroli wall-hung boiler cannot be ignited, it may be caused by burner failure, igniter failure, electric control valve failure, etc. The solution is to check that the burner, igniter, and electric valve are in good working order, and to clean the deposit.

    3.Water leakage fault: If there is water leakage inside the Faroli wall-hung boiler, it may be caused by the aging of the sealing ring, the blockage of the condensate pipe, and the high water pressure. The solution is to replace the seals, clean the condensate pipes, and adjust the water pressure pulsator.

    4.Fault** Hole Silver Limb Display: When the Faroli wall-hung boiler is running, if there is a fault** display, it may be caused by accessories failure, sensor abnormality, water channel blockage and other reasons. The solution is to check that the fittings, sensors, and water channels are in good working order, and to clean the water pipes.

    5.Insufficient hot water failure: If there is insufficient hot water when the Faroli wall-hung boiler is heating or heating, it may be caused by insufficient water pressure, blocked water channel, burner failure, etc. The solution is to adjust the water pressure, clean the waterway and check if the burner is normal.

    In short, when using Faroli wall-hung boiler for heating, it is necessary to pay attention to maintenance and maintenance, regularly check whether the furnace body and pipelines are normal, and deal with faults in time to ensure the heating effect and user safety. If the above solutions cannot solve the problem, it is recommended to contact professional after-sales service personnel or manufacturers for maintenance in time.

  8. Anonymous users2024-01-30

    How to turn off the heating of the farori wall-hung boiler, you can follow the steps below: Feast on the lead and excite Jane 1First, set the temperature on the thermostat to the lowest temperature or turn it off.

    2.Then, close the gas valve to stop the gas**. 3.

    Finally, turn off the power switch to cut off the power**. It is important to note that before turning off the furnace, it is essential to ensure that the furnace is completely cool. If the furnace is still hot, shutting it down can cause serious safety issues.

  9. Anonymous users2024-01-29

    Summary. Hello, to turn off the heating function of the Faroli wall-hung boiler, you can follow the steps below:1

    Find the control panel of the faroli wall-hung furnace, usually located on the front or side of the furnace. 2.Locate the "Heating" button or switch on the control panel, usually marked with a flame icon or the word "heat".

    3.Adjust the Heating button or switch from ON to OFF. 4.

    Confirm that the display or indicator light on the control panel shows that the furnace is turned off for heating. It is important to note that the Faroli wall-hung boiler will continue to provide hot water and other functions after the heating function is turned off. If you need to turn off the furnace completely, follow the furnace's operating manual.

    Are you there. How to turn off the heating of the faroli wall-hung boiler.

    Hello, to turn off the heating function of the Farori wall-hung boiler, you can follow the steps below:1Locate the control panel strap of the Faroli wall-hung furnace, usually located on the front or side of the furnace.

    2.Locate the "Heating" button or switch on the control panel, usually marked with a flame icon or the word "heat". 3.

    Adjust the Heating button or switch from ON to OFF. 4.Confirm that the display or indicator light on the control panel shows that the furnace is turned off for heating.

    It is important to note that the Faroli wall-hung boiler will continue to provide hot water and other functions after the heating function is turned off. If you need to turn off the furnace completely, follow the furnace's operating manual.

    Can you make it clear?

    Do underfloor heating pipes need to drain water.

    Are you there. Can you reply to me?

    First of all, press and hold the switch of the Faroli wall-hung boiler for 5 seconds to turn on the Faroli section of the wall-hung boiler, the display screen will be activated to check the configuration, the dashboard on the right represents the water pressure, the plus and minus signs located at the top are responsible for setting the addition and subtraction of the water temperature, and the plus and minus signs located at the bottom of the combustion finger are responsible for setting the high and low of the heating.

    Can you see if this can help you?

    If you want to turn off the heating pipe of the Faroli wall-hung boiler, it is recommended that you drain the water. Because there may be residual water in the underfloor heating pipes, if it is not drained, it may cause the remaining water in the pipes to freeze, which can damage the underfloor heating pipes. Therefore, in order to protect the underfloor heating pipes and prolong their service life, it is recommended to drain the water in the pipes before turning off the underfloor heating pipes.

    The specific operation method of the cave hall is as follows: first turn off the water pump and power supply of the Faroli wall-hung boiler, and then open the drain valve of the floor heating pipe to drain the water in the pipe. After the drain is completed, close the drain valve.

    It should be noted that during the drainage process, the pressure in the pipe should be maintained to avoid air entering the pipe and affecting the use of floor heating.

  10. Anonymous users2024-01-28

    Kiss! Hello, happy to answer your <>

    The method of adjusting the temperature difference of the pro-Faroli wall-hung boiler is as follows: there is no other Faroli wall-hung boiler temperature difference setting, only the following: This depends on the mode of the wall-hung boiler when it starts, if it is an economic mode, then the temperature difference can be set to about 5 degrees to 10 degrees.

    In order to facilitate the manual operation of the starting temperature difference of the wall-hung boiler, it is best to install a thermostat on the wall-hung boiler, so that it can be adjusted at any time according to the temperature in the room. The tips for using the wall-hung boiler are as follows: 1. When you usually wash vegetables, wash fruits, or take a bath, don't keep turning on and off the switch of the faucet, because every time you start the wall-hung boiler, you will consume a lot of gas and tap water.

    2. When heating, you can set the temperature at home around 20 degrees Celsius during the day, and reduce the temperature to about 18 degrees Celsius at night when you are ready to go to bed. 3. When starting the wall-hung boiler at the beginning, it is necessary to ensure that the temperature of the room is not too different from the temperature of the wall-hung boiler, otherwise it will be a waste of gas. Hope mine can help you <>

    Do you have any other questions?

Related questions
10 answers2024-03-05

1. Power selection: The selection of wall-hung boiler should be based on many factors such as the area where your house is located (different climatic conditions in different regions), location, house area, enclosure structure (villas, bungalows, energy-saving buildings, old buildings, etc.), floor height, floor, unit, heating terminal heat dissipation type (floor heating, radiator, fan coil unit is the most common) and many other factors. >>>More

16 answers2024-03-05

1. In the case of unprecedented prosperity in the domestic construction industry, the construction speed of the municipal heating pipe network is obviously unable to keep up. And the heating demand in the north is urgent. >>>More

8 answers2024-03-05

The meaning of bar in gas wall-hung boiler is the display unit of water pressure. >>>More

13 answers2024-03-05

One. Excellent quality.

The quality of the main components in the wall-hung boiler is reliable, the main components include pumps, controllers, expansion tanks, proportional valves, etc., it is best to choose products with excellent quality and well-known brands, so as to ensure the overall quality and performance of the wall-hung boiler, although the highest is on the high side. >>>More

14 answers2024-03-05

Wanhe wall-mounted what instructions did he follow?