How to connect a mobile phone to an aerial photography drone?

If it's a DJI aircraft, you can ** their app, and the DJI GO app requires iOS or higher and Android or higher. Hantom 3 is perfectly compatible with the DJI Go app for iOS and Android, and the DJI GO app is also compatible with Inspire 1.

iOS: iPhone 5s, iPhone 6, iPhone 6 Plus, iPad Air, iPad Air Wi-Fi + Cellular, iPad Mini 2, iPad Mini 2 Wi-Fi + Cellular, iPad Air 2, iPad Air 2 Wi-Fi + Cellular, iPad Mini 3, and iPad Mini 3 Wi-Fi + Cellular. The app is optimized for iPhone 5S, iPhone 6, and iPhone 6 Plus.

android: samsung s5、 note 3、 sony xperia z3 、 google nexus 7 ii、 google nexus 9、 mi 3、 nubia z7 mini

The list of supported devices is constantly updated and added.

Turn on the drone to turn on the Bluetooth signal, scan the drone signal and click.

Charge the drone and turn it on, so that the drone's Bluetooth signal can be turned on so that the phone can search. Next, enter the phone settings interface, tap Bluetooth in the settings options to enter the Bluetooth settings interface, and turn on the slider on the right side of the Bluetooth options, so that we can turn on the Bluetooth signal of the phone. After the Bluetooth function of the mobile phone is turned on, wait for the signal of the drone to be scanned in the signal below, and then click to connect successfully.

How to take off and land the drone, stay away from the drone, unlock the flight controller, slowly push the throttle and wait for the drone to take off, this is the operation step of takeoff. Among them, to push the throttle, you must be slow, even if you have pushed a little distance, the motor has not started yet, you must take it slowly. When landing, you also need to pay attention to the operation sequence, lower the throttle, so that the aircraft is slowly close to the ground, about 5 to 250px from the ground, slightly push the throttle, reduce the descent speed, and then lower the throttle again until the drone touches the ground, the throttle is lowered to the minimum, and the flight controller is locked.

Landing is a more complex process than takeoff, and it requires repeated practice.

DJI has launched a variety of products and apps, and different products can be used with specific apps to give full play to the best performance.

Here's how to connect your phone:1. Preparation before take-off.

1. Install the battery in the main slot on the drone.

2. Use the data cable to connect with the tablet or mobile phone to install the software.

3. Install the rotors.

Second, the drone is turned on.

1. Press the power button of the remote control, and then press and hold the button to turn it on.

3. UAV flight control.

1. During take-off operation, the double rod is pressed to the middle and bottom (45° angle into an inverted figure-of-eight) at the same time.

2. Flight control, the left stick is up and down, and the fuselage rotates.

3. Flight control, the right stick is the translation of the horizontal plane of the fuselage.

4. Front left button: camera start button and camera angle button, front right button: photo, record, pause button.

The steps on how to connect the drone to the mobile phone to shoot are as follows:Operating environment: DJI Mavic Pro, DJI G04 software, OPPO Reno6 Pro mobile phone, etc.

1. Turn on the drone first, and press the start button twice in a row.

2. Wait for the drone to be successful in self-testing, and then press the start button of the remote control, also twice.

3. Take out the connecting cable and insert it into the connecting port.

<>5. Then take out the cable and connect the phone.

Summary. There are several ways to connect a drone to a mobile phone:1

Connect a WiFi hotspot: Some drones can create a WiFi hotspot that allows the phone to connect and then operate on the drone. 2.

Connect to the receiver: This receiver can convert the control signal of the drone into a signal, and then the mobile phone can connect the signal to obtain the control authority of the drone. 3.

Bluetooth connection: Bluetooth connection can be used, but this connection covers a short distance and is usually only used to control the drone at close range. 4.

Connecting to 4G 5G: A 4G 5G network connection can be used, which enables drones to be controlled from a distance, which is a high-end connection method.

Here are some things you can try.

There are several ways to connect a drone to a mobile phone:1Connect to a wifi hotspot:

Some drones can create a wifi hotspot that allows a mobile phone to connect and then operate on the drone. 2.Connecting the Receiver:

This receiver can convert the drone's control signal into a signal, and then the mobile phone can connect the signal to obtain the control authority of the drone. 3.Connect Bluetooth:

Bluetooth connection can be used, but the connection method of material transportation covers a short distance and can usually only be used to control the drone at close range. 4.Connect 4G 5G:

It can be connected to a 4G 5G network, which enables the drone to be controlled remotely, which is a high-end connection method.

As we all know, UAVs are deeply loved and favored by many young people because of their advantages of small and lightweight, low noise and energy saving, efficient maneuverability, clear image, lightweight, miniaturization and intelligence. However, the camera is an indispensable and important part of the drone, through which we can enjoy the actual shooting picture of the drone. When we want to broadcast the actual video in real time on the mobile phone, we also need to connect the drone camera to the mobile phone to see it.

So do you know how to connect a drone camera to a mobile phone? The following Kai Mo Rui will introduce to you:

Steps to connect the drone camera to your phone:

1. Take out the installed drone and camera first.

2. Point the drone camera at the corresponding position at the bottom of the aircraft.

3. Use a screwdriver.

Pin the camera.

4. Connect the power supply to the aircraft, install the camera, and then install the remote controller bracket.

5. Align the bracket with the corresponding position of the remote control and press the bracket into the card slot.

6. Align the bracket with the screw control behind the remote control, and then use a screwdriver to fix the bracket on the remote control.

7. Fix the phone on the bracket and connect the drone with the phone's Bluetooth.

8. After adding the device, enter the device list interface, device channel, and then you can see the video footage.

9. At this point, the connection of the drone camera to the mobile phone has been completed.

Summary. To connect the drone camera, you need to first make sure that both your phone and the drone camera support Wi-Fi or Bluetooth connection. Here are some basic steps, which may vary slightly depending on the drone and phone model you are using:

Turn on the drone to make sure that the aircraft has been successfully connected to the remote controller, and that the aircraft and the phone are on the same Wi-Fi network or connected via Bluetooth. 3.Open the drone control software and select Connect Camera or Camera mode.

4.You can take photos or videos through the drone control software, and preview the contents of the drone camera. 5.

If you encounter any problems, you can refer to the drone's user manual or contact the manufacturer for help. It is important to note that when flying a drone, you should follow the relevant local regulations and recommendations, and also pay attention to your own safety.

To connect the drone camera, you need to first make sure that both your phone and the drone camera support Wi-Fi or Bluetooth connection. Here are some basic steps, which may vary slightly depending on the drone and phone model you are using:1

On your mobile phone** and install the corresponding land fraud drone control software. 2.Turn on the power of the drone to ensure that the aircraft has been successfully connected to the remote controller, and that the aircraft and the phone are on the same Wi-Fi network or connected via Bluetooth.

3.Open the drone control software and select Connect Camera or Camera mode. 4.

You can take photos or videos through the drone control software, and preview the contents of the drone camera. 5.If you encounter any problems, you can refer to the drone's user manual or contact the manufacturer for help.

It is important to note that when flying a drone, you should follow the relevant local regulations and recommendations, and also pay attention to your own safety.

The factory said to connect the drone camera through wifi, but I don't know how to do it.

Turn on your phone hotspot and then let your drone connect to your phone hotspot.

Set the password of the mobile hotspot by yourself.