What should I do if my Jaeger LeCoultre watch gets into water, what are the hazards, and where can I

If you find that the watch is flooded, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it about 15 cm near a 40-watt light bulb, and bake for about 40 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch directly near the heat, so as not to deform the glass by heating. Because although there is no moisture on the dial, there may still be water in the movement, and the movement will rust and cause damage to the movement after a long time.

After the watch is flooded, it is recommended to find a professional repair outlet as soon as possible for the master to check and deal with it, which can reduce your unnecessary losses.

Daily repair methods for water ingress in the watch:

1. Dry the granules with silica gel. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

3. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe.

Law. 1. Place the vent - dry the watch with a dry paper towel and then place it in a cool and dry vent for a few hours, and do not place the watch directly in the sun or dry, which is to prevent water mist from flowing into the movement.

Law. 2. Silicone drying - for the water inlet of the mechanical watch, you can use the granular substance of silica gel to absorb water, put the two in a closed container, and take it out after a few hours, and the water mist inside will be cleaned up; If it is a quartz point clock, you can take a few small pieces of calcium chloride, wrap them in gauze, and then open the electronic watch cover and seal it.

Law. 3. Wipe oil and remove rust - method 1 and method 2 can only remove slight water mist, and for some more serious water ingress, these two work earlier, which is not enough for the rescue time of the movement, at this time it is best to find a professional watch repair center for maintenance, oil wiping treatment.

The first method is to put the surface facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, using the person's body temperature to remove the water mist, so that the fog in the surface can also be eliminated after a few hours. (This is only suitable if there is a very small amount of water mist in the meter).

The second method: put the watch into the middle of the rice, the rice has the function of absorbing water, if the water mist in the watch is not very much, generally placed for 12 24 hours, the fog in the watch will disappear.

The third method: first pull out the crown of the watch, then use toilet paper or flannel that is easy to absorb moisture, and then heat the watch with a light bulb, which can also remove the water mist. However, remember not to bake the watch close to the bulb or bake it directly, otherwise it will affect the inside of the movement and cause secondary damage.

The fourth method: If you have silicone, you can use the good water absorption performance of silicone, put the silicone and the watch together in a closed container, and the water mist in the watch can be removed after a long time.

What should I do if my Jaeger-LeCoultre watch gets into water? Roast over fire.

If the watch is soaked in water, it can be tightly wrapped with several layers of toilet paper or absorbent velvet cloth, placed about 15 cm near a 40-watt bulb and baked for about 30 minutes, the water vapor in the watch can evaporate. Do not bake the watch directly near the stove to avoid deformation of the watch by heating.

What should I do if my Jaeger-LeCoultre watch gets into water? Wash oil.

Place the watch on your wrist with the inner surface and bottom case facing outward. After two hours, the moisture can be eliminated. If the water ingress is severe, it is best to immediately send watch oil to remove the moisture from the movement to avoid rust on the parts.

Wear the glass inwards and the case outwards on your wrist and the moisture will be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

If the Jaeger-LeCoultre watch is flooded, you can go to Room 04-05, 11th Floor, South Block, Hong Kong Plaza, No. 283 Huaihai Middle Road, Huangpu District, Shanghai. The top priority of the watch is to send the watch to the watch for drying as soon as possible, and if the water is serious, it is necessary to do oil washing.

If you don't do it in time, then the water will make the steel parts in the watch movement embroidery, and the tiny clock parts usually need to be replaced once they rust, and the repair cost in the future will be very large, you must know that the damage to the watch by water is "catastrophic". In addition to movement parts, long-term exposure to moisture can also cause discoloration, blistering and rust on the dial and hands of the watch. Here, I would like to remind you that if it is a watch with repeated water ingress, you need to pay extra attention when wearing it.

At that time, most watches were not waterproof, and most Jaeger-LeCoultre watches were dust-proof. Whether or not a Jaeger-LeCoultre watch is waterproof depends mainly on the tightness of the case structure, and perhaps the most important of the three proofproof properties of Jaeger-LeCoultre watches is waterproof. In the humid environment of the south, even if the watch does not enter the water, the long-term exposure of the watch movement to moisture will cause the mechanism of the Jaeger-LeCoultre watch to rust.

Generally speaking, there are only three places where water can enter the watch movement: the handle (handle), the watch mask and the back cover. The waterproof device is also installed in these three places: add a rubber ring to the shank, add a rubber ring on the threaded edge of the back cover of the sealing ring, shank and other parts, and make the surface tight.

Water and fog into the watch has the greatest impact on the watch movement, and it should be dealt with in time to prolong the service life of the watch. If not treated in time, the residual moisture will easily cause the internal movement to oxidize and rust, resulting in inaccurate watch timekeeping and watch failure.

If the watch is seriously flooded, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage.

International Trade Store: Room 1102, Block D, Bloomage International Center, No. 6A, Jianguomenwai Street, Chaoyang District, Beijing.

What should I do if my watch gets water?

1. If the watch is soaked in water, you can wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, put it at about 15 cm near a 40-watt light bulb, and bake it for about 30 minutes, and the water vapor in the watch can be eliminated.

2. Put it in a rice jar and bury it deep in the dried rice for a period of time, if it is fast, you can see obvious results in one night.

3. You can use a granular substance called silica gel to put it into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will disappear.

4. Take a hair dryer to dry, and then apply a layer of transparent nail polish on it to avoid impurities and prevent rust.

5. If there is water vapor in the watch, you can wear the watch face inward and the bottom shell outward, and wear it on the wrist to eliminate the water vapor in two hours. If there is too much water in the watch, the case must be opened and scrubbed. If you are not sure to deal with it yourself, you should send it for repair in time.

The solution to the water in the watch and the fog on the mirror:

Wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it under the light bulb for about 30 minutes to eliminate the water mist inside, but do not put it close to the light bulb or bake it directly, so as not to cause the surface to be deformed by heating.

Wear the surface inwards and the bottom case outwards on your wrist to remove the mist from the surface after a few hours.

If you have silicone, you can put the silicone and the watch in water into a closed container, and after a few hours, take the watch out again, and the water mist in the watch will disappear.

If the water ingress of the watch is serious, it is best to send it to a watch shop to wipe the oil and eliminate the water in the watch to avoid rust on the parts of the watch.

Note: In order to prolong the service life of the watch, you should try to avoid fog and water droplets in the waterproof watch, do not wear the watch when washing your face, bathing, swimming and other "hydrophilic" activities, do not be affected by water vapor and hot vapor, and pay more attention not to be exposed to rain on rainy days.

Whether it is under warranty or over-warranty, it must be repaired as soon as possible if water enters the body, so as not to affect the service life of the mechanical movement. You can find customer service for after-sales.

Is the water ingress serious, if it is not serious, wrap it in clean toilet paper and bury it in a rice bag for a few days.

How to deal with water ingress into the watch:

If you accidentally get water inside your case, you can use a granular substance called silicone to put it in a meter-closed container with the watch that has accumulated water, and after a few hours, you can remove your watch and the water will disappear. This method is simple, convenient and economical, and does not compromise the accuracy or longevity of the watch. In addition, the silica gel that has absorbed water many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Method 2: If the mechanical watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it at about 15 cm near the 40-watt light bulb, and bake for about 30 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch close to the fire, so as not to deform the watch by heat.

If there is water in the watch, you still have to go to the repair shop to wipe the oil and maintain it to prevent the parts inside from rusting.

Dust entering the dial of a watch is usually due to gradual penetration during long-term wear, if it is a certain length of dust such as hair or acrylic fibers that enters the dial of the watch, it is necessary to pay attention, such dust is very likely to cause the operation of the movement to stop. Do not easily open the back cover for cleaning, and take the watch to a professional after-sales center for cleaning in time.

Daily maintenance of the dial:

1. If the watch is flooded or damp for a long time, it is very easy to induce the discoloration of the dial, or the paint of the dial cover peels off, which is characterized by more occurrences at the edge of the dial. Therefore, when wearing a non-professional diver's watch, try not to get involved in rain, swimming, etc.

2. For long-term collection of watches that are not used, if there are luminous hands, the discoloration of the dial is often at the corresponding position of the hour and minute hands of the watch.

3. If the watch is placed or exposed to sunlight for a long time, all kinds of rays in the sunlight will make everything slowly change color, so try to expose the watch to the sun as little as possible.

Room 1102, Block D, Bloomage International Center, No. 6 Jianguomenwai Street, Chaoyang District, Beijing.

Room 808, Block E1, Oriental Plaza, Dongcheng District, Beijing will answer for you!

Dear, yes, your watch is likely to be waterproof, today's watches basically have a waterproof function, 30m, 50m, 100m waterproof depth is common in watches. But even if it has a good waterproof function, it is difficult to ensure that it is not a secret. It is very likely that it is the reason why the water enters and then rusts and does not go, it is recommended that you take it to repair as soon as possible) The top priority is to send the watch to the watch repair shop for drying as soon as possible, and if the water is serious, it is necessary to do oil washing.

If it is not repaired in time, the water will cause the steel parts in the watch movement to appear raw embroidery.

Jaeger-LeCoultre Watch Aftermarket Service Center: 400-6590-877

What to do when your Jaeger-LeCoultre watch is in water: When the watch is used in water, the crown is not properly screwed. There is a seal between the adjusted watch lug and the watch dial that is more convenient for water ingress. If the watch is unplugged when using the watch in water, then the watch may get water.

If the mechanical watch gets into the water, open the back cover. Treating the moisture inside with desiccant, etc., and then replacing the waterproof rubber ring can solve the problem!

If the watch is flooded, the best way to deal with it is to go to an authorized repair network for maintenance, which is more expensive, but it is mainly guaranteed.

If you really don't want to go to a repair shop, you can consider wrapping your watch in a paper towel or thin non-woven fabric and putting it in a dry rice jar to let the rice absorb moisture.

After the watch gets into the water, I need to go to the counter watch repair point to disassemble and clean it. Otherwise, it will damage the parts on the other side of the movement.

What should I do if my Jaeger-LeCoultre watch gets into water? Jaeger-LeCoultre watches are a very good watch. If the mecha watch gets into the water, you don't want to go to the repair shop to repair it, so you can only go to the after-sales service for repair. Such***.

Answer the reason why the watch does not go: the main core gear is misaligned, the watch is magnetized, bumped, and the oil sludge is dried for a long time. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch suddenly stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours. When the quartz watch stops, it is necessary to consider whether it is caused by the battery failure, and go to the after-sales service to replace the battery.

If the watch is used for a long time, then its wear and tear will be more serious, and the external maintenance of the watch will be easily damaged. It is necessary to regularly replace the watch you are wearing, and it is necessary to maintain the watch regularly, for the service life of your watch, it is better to maintain it regularly.