The wiper is not clean, is it time to change the rubber strip

The wiper is not clean, which is generally caused by the aging of the wiper strip. You can check and replace the wiper strip to try.

Hello, if you can't scrape clean, it doesn't necessarily mean that the wiper blade is not good, sometimes the wiper arm pressure is not enough.

Hello In this case, if the wiper blades are not clean, it means that the wiper blades are aging, or there is oil stains on the glass.

Hello, this is the need to replace the strip, generally speaking, the strip needs to be replaced every two years.

Hello, the wiper should be replaced if it is not clean, and the wiper should be replaced once a year or so.

Yes, the wiper is not clean because the rubber strip on the wiper is broken, and it should be replaced with a wiper.

As follows:

1. When replacing, prepare a clean soft cloth, twist the car key to the energized position, and quickly flip the wiper block to let the wiper stay in the erected position to facilitate the replacement of the rubber strip;

2. There is a small square button on the wiper rod, press the button to pull out the old wiper strip and remove the protective cover;

3. Plug the square mouth at the lower end of the new rubber strip and send the rubber strip along the steel sheet track.

IntroductionWipers, also known as wipers, water dials, wipers or windshield wipers, are equipment used to brush and scrape rain and dust attached to the windshield of vehicles to improve the visibility of drivers and increase driving safety. The wiper is composed of an electric motor, a reducer, a four-link mechanism, a wiper arm mandrel, and a wiper blade assembly.

Prepare a pair of needle-nose pliers, the only place to use the tool is to remove the strip to open the wiper on both sides of the two iron clips used for positioning, and the strip can be pulled out.

There are two steel bars in the middle of the rubber strip, put the old and new rubber strips in place, pull out the steel strips and press them on the new rubber strips. The steel bar is curved, so be careful not to make the two in reverse direction when installing.

Break the two steel strips and replace them with the adhesive strips.

The so-called wiper is a tool for simple cleaning on the front glass of a motor vehicle to prevent rain and other dirt from affecting the line of sight.

The wiper assembly includes an electric motor, a reducer, a four-link mechanism, a wiper arm mandrel, a wiper blade assembly, etc.

When the driver presses the switch of the wiper, the motor starts, and the speed of the motor drives the swing arm through the deceleration and torsion increase of the worm gear and worm, and the swing arm drives the four-link mechanism, and the four-link mechanism drives the rotating shaft installed on the front dash plate to swing left and right, and finally the wiper blade is driven by the rotating shaft to sweep the windshield.

When replacing the wiper strip, prepare a clean soft cloth, twist the car key to the energized position, quickly turn the wiper block, let the wiper stay in the erected position to facilitate the replacement of the strip, there is a small square button on the wiper rod, press the button to pull out the old wiper strip, pull out the protective cover, plug the lower end of the new strip into the square mouth, and send the strip along the steel track inside.

The steps to replace the wiper strip are as follows:

1. After finding the rubber strip that can slide, you can remove the clip used to fix this end, generally speaking, the clip is not difficult to get down, if it is particularly tight, you can use needle-nose pliers to assist in dismantling.

2. After the clip is removed, you can see that the rubber strip to be replaced is fixed on the wiper through a metal buckle, and then as long as you pry the metal buckle up with the clip or something, you can remove the rubber strip.

3. The installation of a new wiper rubber strip can be followed as long as it is carried out in reverse according to the steps just mentioned, but special attention should be paid to here that the metal buckle that fixes the rubber strip must be fixed tightly, otherwise the rubber strip will produce a position shift in use, which will affect the use effect.

1. Install the wipers, press the square button on the wipers, and remove the wipers from the swing arm.

2. It is best to cover or wrap the windshield wiper swing arm with a soft cloth so as not to hurt the glass surface and gently return to the windshield.

3. Bring the wipers indoors, clean them thoroughly, and put them away.

4. Remove the wiper strip from the package and soak it in soapy water.

5. Pick up the wiper of the original car, pinch the wiper rubber strip on one side with your fingers, and pull it back and forth, you will find that one side can be pulled on both sides, and the other side is not.

6. Find the side that can't be pulled, and use a thin screwdriver to pry open the plastic wiper plug on that side.

7. The effect after removal.

8. Use a small screwdriver with a word to gently pry up the metal hook, and then you can pull out the rubber strip without the metal hook.

9. Soak the new rubber strip in soapy water to replace it, then gently clamp the metal hook with pliers to connect and fix the new rubber strip, and finally cover the plastic plug to replace the wiper.

1. The wiper needs to be removed before replacing the rubber strip of the wiper.

2. Check that the rubber strips at both ends of the wiper can not slide back and forth, and the part that cannot slide is the part we want to remove.

3. After finding the rubber strip that can slide, we can remove the clip used to fix this end, generally speaking, the clip is not difficult to get off, if it is particularly tight, you can use needle-nose pliers to assist in dismantling.

4. After the clip is removed, we can see that the rubber strip to be replaced is fixed on the wiper through a metal buckle, and then we only need to pry up the metal buckle with the clip or the like, and then we can remove the rubber strip.

5. The installation of new wiper rubber strips can be followed as long as they are carried out in reverse according to the steps just mentioned, but special attention should be paid to the fact that the metal buckle that fixes the rubber strip must be fixed tightly, otherwise the rubber strip will be offset in use, which will affect the use effect.

How do I change the wiper strip myself?

OK. The wiper only needs to change the rubber strip, and the wiper skeleton of the original car is very strong, and there is no need to replace the whole set, and the rubber strip can be changed.

Wipers are broadly divided into two types: traditional intermittent and raindrop-induction. Raindrop sensor type, mostly used in mid-to-high-end models. A good wiper must have the characteristics of heat resistance, cold resistance, acid and alkali resistance, corrosion resistance, can fit the windshield, reduce the burden on the motor, low noise, strong water repellency, soft and does not scratch the windshield, etc., so that you can see clearly.

Car wiper precautions.

If the front windshield is too dirty, it is best to gently and briefly clean the windshield with a dry cloth to reduce unnecessary wear and tear on the windshield wipers.

When the wiper blades have poor wiping, try to soak the wiper blades with water first, polish the wiper blades back and forth with water sandpaper, and then clean them with clean water and put them back into the windshield, and then try to scrape them to see if there is an uneven place.

Wiper strips can be divided into two types: boneless and boneless.

When replacing the wiper blade, turn off the power first, there is a small square button on the wiper lever, press the button and pull it up to remove the wiper blade.

There are steel bars in the bone wipers, and when dismantling, remove the steel bars, install the steel bars on the new wiper rubber strips, and put them back on.

Boneless wipers, pull out the protective covers at both ends to pull out the old rubber strips, put the new rubber strips back along the track of the steel sheet, and then put the glue set.

As long as the wiper skeleton is not broken, you can only change the rubber strip.

Before changing, it is necessary to determine whether the wiper of the original car is boneless or boneless, as well as the size of the rubber strip, which can also be judged according to the specific model.

The installation is also very simple, and the instructions are on the box of the adhesive strip.

Yes, the boneless wipers used in most models can only be replaced with rubber strips, and they can be replaced in about 2 years.

However, it is certainly not as good as buying a whole, and now the one-piece boneless wipers are also quite cheap, and there is a pair for ten yuan, and it is also a good choice to exchange it for a year.

The wiper can only replace the rubber strip, like the boneless wiper has a rubber strip and a steel strip inside, you only need to pull out the steel bridge and replace it with a new rubber strip and install it in place.

The car wiper can only replace the rubber strip, but the process of replacing the rubber strip is more complicated, and only if the rubber strip is replaced, the service life is not long, and the ** of the wiper blade is not very expensive, it is recommended to replace the wiper blade assembly directly.

The scraper can be changed together, or only the rubber strip can be replaced, but a replacement is not much money, and it saves trouble.

This wiper is composed of wiper blades and wiper arms, and the replacement is to replace the wiper blades, which are divided into ordinary and boneless, which are not high, if you shop online, Pinduoduo** can be bought, and it is much cheaper than the physical store.

No, it doesn't cost much to change overall.

Wipers can only replace tape, like boneless wipers have tape in them and steel bars inside. If you need to remove the steel bridge, replace it with new tape and install it in place. If the damage is larger, it needs to be updated.

Pay attention to the use of wipers:

In the process of daily use, the wind and sun in summer, and the cold and rain in winter will lead to serious aging of the wipers, unclean cleaning, abnormal noise, etc. In general, the life of the wiper is 6-12 months and needs to be replaced regularly, otherwise it will affect the driver's eyesight.

Wiper maintenance:

Buy the corresponding cleaning agent, regularly clean the stains on the wiper with the cleaning agent, clean the remaining oil stains on the windshield, ensure that the wiper can be cleaned, and have a wide field of vision when the Gongqing hidden code is made; After driving for a long time, the wipers need to be replaced to prevent the wipers from aging and hardening due to weather.

Millions of car purchase subsidies.

Car wipers are frequently used car parts, if the wipers of the car fail, then change the wipers or change the rubber strips?

If only the rubber strip of the wiper is aging, it is recommended to replace only the rubber strip of the wiper, but if the skeleton of the wiper has been aged, such as rust and deformation, it is recommended to directly complete the wiper. The quality of the original wiper skeleton of the car is very good, and the quality of the replaced wiper is usually not as good as the original, so it is recommended that the owner and friends can change the rubber strip on the rubber strip, and only consider changing the whole set of wipers when the skeleton fails.

The rubber strip of the wiper is very easy to age, under normal circumstances, the rubber strip needs to be replaced once a year to two years, if it is not replaced in time, not only can not clean the windshield, but also cause damage to the windshield, so when the wiper fails, the owner friends should replace it in time, and also ensure that the driver has a good vision and ensure the safety of driving.

<> "If the wiper is not clean, you have to replace it?

For this situation, there are a large number of novice car owners who take it to 4S or auto repair shops to deal with it, but for those veterans, they can easily get it right!

First of all, the wiper blade must have something to do with the wiper blade, under normal circumstances, the wiper blade is always exposed to the wind and sun, and has experienced the wind and sun, and has accumulated bird feces and small gravel! I don't usually feel it when it's not raining, but as long as it rains, there are a lot of water stains on the front windshield! In fact, you can take out the wiper blade and clean it yourself!

But you have to have a certain amount of hands-on ability, such as being able to disassemble the wipers, be especially careful not to break the outer skeleton, and clean up the entire wiper blade with a rag after taking it out!

Finally, remember to rinse with water, this operation is repeated back and forth several times, and there will not be so many water stains if you use the wiper in the future!

Precautions for beginners on the road:

1. Novices must have a good driving mentality when driving on the road.

Novices are generally nervous about driving on the road, which is actually very unfavorable to normal road driving, and people are very busy in the situation, it is easy to make wrong judgments, and the "wrong accelerator" is the reason why they usually see the news. Therefore, novices should adjust their mentality before going on the road, and silently recite the eight points of precautions for novices on the road, so that they can not panic when driving in danger.

2. Conscientiously abide by traffic laws.

According to the statistics of the traffic department, more than 80% of traffic accidents are caused by a party's violations. Traffic laws are the "predecessors" in exchange for lessons and experience, and obeying traffic rules is the most important issue to pay attention to when novice driving, so that it is possible to minimize the probability of traffic accidents.

3. Control the steering wheel while driving.

Novices on the road must master the five most basic principles: starting, parking, steering, shifting, and braking. These five principles should be flexibly applied according to the actual situation.

For example, turning: there is never a universal, universal angle of turning the steering wheel, which can be applied to every corner, after all, the width of each intersection is different, not to mention the influence of other vehicles and pedestrians, it is impossible to say that every intersection is 50 or 60 degrees can just turn appropriately. Therefore, at this time, we are required to observe the rearview mirror in the car, and the left and right rearview mirrors to adjust the direction and the angle of the anti-noise plate to carry out flexible movements.

Of course, in the actual situation, there will inevitably be foreign objects such as sediment on the glass surface, which will inevitably affect the life of the wiper during use, and at the same time, according to the actual driving situation of each person, under normal circumstances, it is recommended that the wiper be replaced once a year.

First of all, you have to observe, after the wiper has been scraped, whether there are obvious water marks on the glass, or even a leaky place, we can stand up the wiper with a line, touch it with your hands, and see if the rubber strip on its surface has hardened, or there are obvious cracks, at this time you can also replace it, and the specific situation should be analyzed specifically. In the first case, if the wiper makes some squeaky sound during use, then you should immediately check whether there is a foreign object under the wiper, there may be some small stones, small branches or something, and it can be used normally after being removed.

Another is that the poor use effect is not necessarily the problem of the wiper itself, but the angle between it and the glass is not suitable, so it will not be clean, then you only need to use a wrench to gently adjust the angle of the wiper.

In the last case, if the wiper can not be used, in fact, there is no need to go to the repair shop, you can first check whether the rubber strip is aged, and at the same time apply the toothpaste on it, which also has the effect of protecting the rubber strip, if the damage is serious, you can replace it yourself, because the wiper is still relatively simple to replace, you can choose to buy it online, or buy it in a physical store, if you are really not familiar with it, you should consult others in time.