I just installed the router and there is wifi but the host is not connected to the internet

Problem 1: All WAN port parameters are 0 and the connection is always in progress, but the connection cannot be successfully (log in to the management interface of the router and click Running Status >> view the WAN port status);

Solution: 1. Check the line, if the line is connected correctly, but the WAN port indicator is not on, please check whether the WAN port wiring is in poor contact, etc., and try to replace the network cable connected to the WAN port;

2. Confirm that the password is entered correctly, click Running Status >> WAN port status on the management interface of the router, if the WAN port does not get the IP address, the page will have a prompt for the reason of dialing failure, modify it according to the prompt;

3. The broadband service provider binds the MAC address, connects the computer that was connected to the broadband Internet access separately with the LAN port of the router (here it must be connected by wire), and logs in to the management interface of the router. Select Network Parameters >> MAC address clone, click Clone MAC address. When the MAC address is the same as the MAC address of the current management PC, click Save and Restart the Router.

Solution: 1. The computer needs to be set to automatically obtain the IP address - if the computer has automatically obtained the IP address, but the IP address obtained, please disable the local connection or wireless connection corresponding to the computer and then enable it.

2. Check the router's Internet access control - the router's parental control and Internet control (some routers are set by firewalls) function can restrict the Internet access permission of the intranet computer, please set the function according to the actual needs, if it is not necessary, you can not enable the function. Here's how to set it up:

1) Turn off Parental Controls - Log in to the router management interface, click the Parental Controls settings page, select Disable and Save.

2) Turn off Internet Access Control - In Security Settings >> Internet Control, make sure that Turn on Internet Control is unchecked, and click Save.

3. Check the browser settings - please check the browser settings, the check method is as follows: Disable dial-up connection: Open IE browser, click Tools >> Internet Options, select Connect>> never dial-up connection; Disable Network**:

Click Tools >> Internet Options, select Connect >> LAN settings, make sure none of the three options are checked, and click OK.

After setting up, try to open the browser to surf the Internet;

4. Change the browser or computer - try again after changing the browser (using Firefox, Google Chrome or other browsers), if you still can't access the Internet, try to change the computer for comparison and testing;

Let's take a look at the light on the router to see if the light is on, turn on and you enter the router to see the running status, whether the IP address has been obtained in it, if not, it means that your broadband account is wrong or the password is wrong, reset it.

If the light does not turn on, it means that your external line is not connected, call the operator's **warranty.

I don't need to install it, I don't believe you just plug in a router, and there is wifi

Broadband should also be connected.

Installed router no wifi hello dear, <>

Reason 1: The name of the wireless network (wifi) has been changed or turned off, and the family members or friends who connect to our wireless router to access the Internet can enter the login page through the wireless connection, enter the password, and enter your router settings. Go to the router configuration page, find the system settings, and restart the router.

There is a fault in the quality of the router that causes the router to not work properly, which may be rare, but it must also be taken into account. Hope it helps. If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress.

Finally, I wish you good health and a good mood!

The router has no wifi signal, it may be that the router has a hidden wifi signal, so the router's wifi signal cannot be searched. It could also be that the router's wifi is turned off and the router is not emitting a wifi signal. The solution is to log in to the settings interface of the router and open the Wireless Settings (WiFi Settings) menu, and in the page that opens, check whether the relevant settings of WiFi are correct.

Let's use a TP-Link router as an example to demonstrate how to log in to the router's settings interface and check the steps of WiFi-related settings. For other brands of routers, the content displayed in the settings interface is different, but the operation steps are the same, and you can refer to the following methods. 1.

Connect your computer to the LAN port of the router with a network cable.

1. See whether the IP of a ** machine and a notebook or a device that accesses the Internet through wireless Internet is in the same IP segment (normally, only the last two to three digits are different, such as a 100 and a 101, etc.), whether the gateway is exactly the same, and whether the DNS server is exactly the same (including the spare DNS).

2. If it is not in the same IP segment, it means that there is a problem with the configuration of the desktop network card, or there is a problem with the network cable (if the IP is starting with 16, it must be a network cable problem), the network card configuration can be manually configured, and the IP address is entered by yourself, as long as the IP address of the network cable device is in the same IP address segment, the subnet mask is default, the gateway should be the same as the gateway of the wireless device, and the DNS should be the same as the wireless device.

3. If the IP address is in the same address range, but the DNS is different, it means that there is a problem with the DNS setting, and it is good to modify it manually.

4. If the gateway is different, it means that there is a problem with the line connection or the configuration of the network card.

5. If there is no problem with the above, then click Start-Run-Enter cmd and press Enter, enter ping to see if there is a ping result returned, if all are timeout, it is a problem with the router, if there is a result, it is a problem with DNS, enter ipconfig flushdns and then restart the computer to try.

1. Are you really set up all of them?

Clause. First, if you want to use a router to access the Internet, the dial-up in the original computer must be canceled.

Second, the system status of the router should be seen to be connected to the external network and obtain the correct IP, the key is that you should set the way to access the Internet and the user name and password in the router.

Clause. 3. Your computer must obtain or set the correct IP and DNS of the routing network segment.

If you do all three, you'll definitely be able to access the Internet.

Here's why:

The router is not set up correctly.

The computer does not have an IP address or DNS set up for automatic acquisition.

Solution: Set up the router again according to the setup steps.

Win7 system setting method:

Right-click [Network] Properties [Change Adapter Settings] [Local Connection] [Right-click Local Connection Properties] [Double-click TPC IP Protocol] [Then click "Automatically Get IP Address"], and then click "Automatically Get DNS" Server Address] [Click OK].

It is possible that the wireless receiver of your book is not turned on, and you can see if the wireless indicator light on the book is on.

Is it really connected? To be set up,Generally speaking, there is a piece of paper on the back of the router,Among them, there is an IP address in the browser first, which is required to be on the password paper,After entering, it is connected at the midpoint of the running state, and then automatically connected at the midpoint of the WAN port in the network parameters。 If not, let's get back!

It may be that there is a problem with the network cable and you press it a few more times.

Check the configuration of the wireless router, whether the wireless function is turned on, whether it is set to PPOE mode dial-up Internet mode, anti-telecom MAC lock call 10000 to reactivate it.

Do you have a wireless router on a desktop, do you have a wireless router receiver, or do you connect to a computer?

Double-check according to the instructions.

Are you sure it's a desktop host? Are you sure it's a wireless router?

If it is, it's normal if you can't get on, and the host doesn't have a wireless network card.

It's best to tell me what you're configuring.

Do laptops use wireless Internet access? Is the wireless network card bad?

Is the laptop disconnected or IP conflicting?