Tengda s W316R wireless router is set up, but it can t access the Internet, and it keeps showing up

Open the network and go to the login interface, which means that you haven't set it up at all, and if you set it up, it won't be transferred

Do you use a telecommunications line to access the Internet? In the case of telecommunications, it must be cracked before the routing function can be used.

Your router is set up incorrectly, and the Internet is filled in with your cat (dial-up Internet). I didn't want to fill it in by myself.

First, check whether the network cable is connected normally, it should be connected to the computer from any of 1, 2, 3, and 4. If you're using a wireless connection from your laptop, you'll need to connect it before you can access it. The second is to look at the label on the router.

Look at the IP above. If that doesn't work, then force a factory reset.

Use a network cable to only connect your PC and the router, then reset the router, and then see what the management address is written in the manual, some are, different. Then type the correct admin address into the browser.

Start by setting the computer IP in a section, such as:

Here's how to set up your router:

1. Line connection:

a.Connect the network cable from the cat to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1, 2, 3, 4).

b.Connect the broadband cable to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1 2 3 4).

2. Log in to the router interface.

In the browser, type: Enter, enter in the pop-up page: admin and click "OK".

3. Set up the router to surf the Internet.

Before setting up the Internet access, choose the correct Internet access method: Generally, there are three types as follows:

ADSL dial-up: Usually to access the Internet (when not connected to the router) need to click on the broadband connection, dial-up is successful before you can access the Internet, you should choose the Internet mode, Internet access and Internet password correctly enter the broadband and password, you can.

Automatically obtain an IP address: If you usually surf the Internet (when you are not connected to the router), you only need to set the local connection of the computer to automatically obtain the IP address to access the Internet, you should choose this Internet access method.

Static IP: If you need to fill in a fixed IP address in the local connection to access the Internet (when you are not connected to the router), you should choose the Internet access method, log in to the interface of the router, click "Advanced Settings" - "WAN Port Settings" to select the static IP mode "Static IP Mode", and enter your fixed IP address, subnet mask, gateway, DNS domain name server and other parameters correctly.

4. After setting, click "Advanced Settings" - "System Status" to check whether the connection status of the WAN port shows that it is connected, and whether the connection mode is displayed correctly.

The corresponding connection mode for ADSL dial-up is: PPPoE

The connection mode corresponding to the static IP address is the static IP address

Login IP address.

Login username password admin admin

Or press the reset button for more than 7 seconds to restore the factory settings.

Who told you that that little button is a factory reset? Enter and try, the account password is admin, and there is a factory reset in it.

Tengda's routers often have problems, and it is generally not recommended to use them, I recommend that you use TPLink or DLink to be durable. A factory reset can only be restored by inserting a pin into a small hole next to the router.

Some routers need to be turned off for factory reset, and there are also IP addresses to try.

First of all. If you router the lights are already on. Basically, it can be said that there is no problem from the cat to the route.

Then if the Internet light on your cat is also on normally, then the network is basically normal, if you can't access the Internet at this time. Then, go to the routing settings. In the Network Settings page.

The WAN port is set to PPPoE mode. Then fill in the username and password for your broadband. Then remember to select the auto-connect mode.

Once the setup is complete. Click to connect or save and restart the route. It should be normal at this point.。。

On the home page of the routing settings page, the connection status of the internal network and the external network will be displayed, and you can check whether the external network is connected normally (after the normal connection, the external network will display various information such as IP mask, gateway, DNS, etc.). If the IP address of the external network port is not displayed or displayed, it means that the external network is not properly connected. There are many possible reasons, such as different cats, wrong adsl lines, wrong account passwords, etc.

The maintenance method is to use the computer to directly connect the cat to dial-up to see if it can be connected normally. If it can be connected normally. Also remember to reset the username and password on the tool change route to prevent these errors.

Secondly. The dialing method of some ISP broadband users is more special, such as Henan Unicom, the dialing software used is Broadband My World, and the PPPoE of the system directly fills in the user name and password is not normal use. You'll need to change your username (beyond the scope of this discussion).

The router doesn't have autodialing. Set up an Internet account and password in the route, the setup wizard comes step by step, it's very simple, you really won't go to the place where you buy the route, let him help you set it up, you can use it!