The router can t connect to the network, what s going on?

1. According to the information on the back of the router, log in to the wireless router management interface. First of all, you must set the "Internet mode" of the wireless router correctly. The specific setting method is related to the network access information provided by the network operator.

2. Enable "DHCP Server" to achieve automatic IP allocation.

Switch to the "Advanced Settings" tab, click on the "DHCP Server" item, and check the "Enable DHCP Service Item".

3. Set the computer IP acquisition method to automatic, and then try to use the computer to connect with the wireless router wirelessly or wired, and try to access its network.

4. Before accessing the wireless router on your phone, you need to reset the wireless encryption mode. In the wireless router management interface, switch to the "Wireless Settings" tab, click "Wireless Encryption", and set the "Security Mode" to "WPA2-PSK".

5. At the same time, reset the password of the wireless network so that you can use your mobile phone to access the wireless network correctly.

6. After the above settings, you can try to use your mobile phone to connect to a wireless router to achieve a free Internet experience.

You're not right, right? Internet access with a new password?

The router can be connected but cannot access the Internet, which may be caused by a variety of reasons. First, it could be an issue with the router itself, such as a misconfiguration, firmware issue, or hardware failure. Second, it could be a network issue, such as a lost internet connection, a DNS server failure or IP address conflict, or a communication issue between devices.

Finally, it could also be a problem with your end device such as a computer or mobile phone, such as a problem with a network card driver, firewall settings, or a virus infection.

To solve this problem, you can take the following steps:

1.Check the router connection: The first thing to do is check the status light of your router to see if it is working properly.

Then, log in to the router background and check if the various settings and configurations are correct. If the router is not configured correctly, or if the wrong network settings are used, the network will become unreachable.

2.Check the network connection: If the router connection is normal, but the Internet connection is still not connected, you can check whether the Internet connection is normal.

Check the modm's status light to see if it's connected to the internet, or restart the modem. You can also make sure that your network connection isn't interrupted by going to Other** or an app to check if your network connection is working. Alternatively, you can try changing the DNS server address to resolve issues with your network connection.

3.Check the device: If neither the router nor the network connection can completely solve the problem, it is necessary to check the problem of the terminal device such as the computer or mobile phone.

If your device's firewall or virus security software is not set up correctly, it may result in the loss of access to the internet. You can also try restarting your device, upgrading your network card drivers, and more.

In short, it is a very common problem for the router to connect normally but cannot access the Internet, and the solution is relatively simple, you need to check the possible causes one by one, and troubleshoot the fault points, and finally restore the normal network connection. <>

The router can be connected, but it can't access the Internet normally, which is related to the following reasons:

1. If the router is faulty, if the broadband information is filled in correctly, the router can be restarted, and it may be restored.

Precautions. If the optical signal indicator flashes red, and there is no arrears when you call customer service, then it may be caused by an external network failure, the most common being that the optical fiber is cut off, hung up, and encountering extreme weather, etc., resulting in temporary paralysis of the external network network.

In addition to the above three common situations, there are also some situations that may cause the router to be connected to the Internet, but unable to access the Internet, such as optical modem damage, router damage, network cable interface damage, network cable damage, etc., but under normal circumstances, these devices and lines will not have problems, and can only be checked and eliminated one by one according to the actual situation on site.

Level 1 2008-09-02

It's your wrong cable It's the same in my house I call your computer that was originally connected to the cat and didn't use the router as the first computer Hamai router will have two cables Right, the short one is connected to the ethernet hole of the cat The other end is connected to any of the three jacks in the middle of the router Note: Do not wire the WAN port The long one is connected to any of the three jacks in the middle of the router The other is connected to the second computer Your first computer and the cat also have a cable connection Now connect one end of that wire to any of the 3 holes in the middle of the router The other end is still connected to the host of your first computer and don't move Now look at the light on the m2 2 3 hole on the router "My house is like this, just as an example" Doesn't the cat also have two ports? The other end of the line is connected to the ** line, don't move and re-set the IP, it's good It seems to be a bit cumbersome to say Oh, I'm sorry, I hope it helps you.

Sometimes, I don't know why this happens, a small exclamation mark is displayed at the wireless network, although it is connected, but it cannot access the Internet. How to deal with this situation? Why can't I connect to the Internet when I connect to the wifi?

Enter the address behind the router in IE), press Enter, and the login interface appears Enter the password: admin. Enter the settings interface, select PPPoE (Auto-Dialing) connection, and enter the information you have in the carrier (Telecom, Netcom.

and password for you. And then the next step, the next step... Then check the network connection status to see if there are any changes in receiving and sending data.

Then on another computer, right-click on the network neighbor, right-click the local connection, attribute Internet Protocol and select Automatically get IP to automatically get DNS, and then click OK.

Point advanced Turn off the fire prevention situation.

Finally, restart your computer.

Don't be so troublesome, just do it as I said, it's OK, restore the router exit settings before the operation, keep it safe.

When the router dials the number, the password is not correct, oh re-set it again, ask what the correct password is.

You go to the router and see if your router network dial-up is successful.

The mobile phone is connected to wifi, but it still can't access the Internet, and the broadband master will tell you, **Something is wrong.