Tengda Wired Router TEI4O2 heating up caused my wireless router not to work, wifi not connecting

No, it won't! My house is also two routers, and they are also put together, and there has never been a situation like you.

Originally, both routers would be hot, if your wireless can't play the role of wifi, it should be that it transmits non-wireless signals.

You have to turn on the broadcast in the wireless settings, and do you have the right wireless routing settings?

If they are all set up, it is estimated that the wireless transmission module in your wireless router is broken.

In fact, it is not necessary to have a wireless router to do the wifi function to surf the Internet.

Now the national wifi plugged into the computer can also be used as a wireless network, and the mobile phone and tablet can do wifi Internet access.

It is relatively simple to use, not so troublesome to set up routing, plug and play, automatic installation to create wifi, powerful signal and many functions.

It can avoid a lot of trouble, I personally think it's very good to use, hope.

Hello landlord! Maybe it's not set up well, you can try to bridge the two routes, first log in to the browser, username admin, to set, don't set the names of the two routes to avoid trouble. Same.

Set the IP address to the status of automatic acquisition.

I think the routing setup is cumbersome, and even changing the password is also troublesome. I'm using Tencent now, it's plugged directly into the computer, the phone can be connected by scanning it, and you can plug the wifi into one.

On the computer, the other ones can be directly connected to the wireless, and the network speed is still very fast.

Hope I help you, thank you, hope!

There is also a wired router connected to the wireless router at the next level, why bother?

The main reasons are:

1. The distance between the terminal device and the wireless router is too far to find or connect to the wifi signal, so the distance between the terminal device and the router can be shortened.

2. There is a problem with the router settings that causes the mobile phone to not connect to the WiFi, for example, the router hides the WiFi name, so the terminal device cannot be found and cannot be connected, or the router sets the MAC address of the terminal device to the blacklist and is rejected by the router; You can restart the router to solve the problem, reset the router if necessary, and then reset the network parameters before connecting.

3. If the terminal equipment cannot be connected to the wifi due to the quality problem or failure of the router, this situation needs to contact the after-sales service of the router for maintenance or replacement of the router to solve.

4. If the system problem of the terminal device causes it to be unable to connect to the wifi, you can restart the terminal device to solve it, and if necessary, you can consider restoring the system of the terminal device to the factory setting state or upgrading to the latest version to solve the problem.

5. The hardware failure of the terminal equipment will also lead to the failure to connect to the wifi, such as the failure of the network module, the antenna, the failure of the motherboard chip, the failure of the internal circuit or other components, etc., which needs to be repaired by contacting the after-sales service of the terminal equipment to solve the problem.

1. It is recommended to log in to the interface of the router to modify the wireless configuration, click "Advanced Settings" - "Wireless Settings" - "Wireless Basic Settings", change the wireless signal name (SSID) of the router, if you can change it to tenda123, and then reconnect.

2. If it still doesn't work, please cancel the wireless password of the router, and then connect, if this connection means that your network card is compatible with the encryption mode of the router, it is recommended to change the encryption mode.

Did you go inside the router and set it up? Either remove the encryption, or slow down the speed. What to receive, some old machines can only use 11m.

In the IP settings of the router, you can put an IP address that is different from the other route.

Didn't you set the router? If you're installing telecommunications, you can ask them to come and have a look.

How many lights are there in total? That light doesn't come on? Be detailed.

Hello, the wireless wifi of the router cannot be connected, it is recommended that you reset the router to factory value, and then set it up again, and place the router in a ventilated place so that it is conducive to the heat dissipation of the router.

Stick the route to the slate so that it will heat up quickly.

Can the landlord take a closer picture?

Follow in order.

1.First, use your computer to connect to Tengda's wireless router, and enter the settings page (usually or)2Run the setup wizard, select Dynamically obtain IP address as dial-up method, and set the name of your wireless router's SSID (try not to use the default one to prevent conflicts with duplicate names), and set the key, after completing the last step, the router will ask to restart.

3.Check the network cable you received from the router in the house you live in, find the WAN port of the wireless router, and then try to get off the computer to see if you can access the Internet? If you can, search for the Wi-Fi signal on your tablet, search for the name of the wireless router you just changed the name of the SSID, select the connection and type the key to surf the Internet.

There are two important points: first, in the way of surfing the Internet, you should choose the way to dynamically obtain IP; Secondly, connect the network cable you pulled out of the router in the house to the WAN port of the wireless router (usually blue, the color is different from the other ports anyway).

Finally, remember to set the name and key to your wireless router

The IP of the router has conflicted.

1. Line connection: any interface of the LAN port of the wired router is connected to the WAN port of the wireless router, 2. Log in to the wireless router management interface, select the "automatic acquisition" Internet access mode, click "Advanced Settings" - "LAN Port Settings", and change the IP address of the LAN port to other network segments, such as, you can!

1. Enter the wireless router interface.

2. Modify the IP address of the wireless router, not the same as the higher-level router) 3. Find the DHCP service and turn it off.

4. Do not plug in the WAN port of the wireless router (in order to prevent misoperation, it can be temporarily closed with plastic transparent glue), and all LAN ports can be used.

5. All programs are over, over

Add an intranet, set the LAN port of the router, change it or others, as long as it's not.

This one is simple. Just plug the connected network cable into the LAN port.

There is no need for any setup, you don't need to use the route mode, but you don't need to go to the wireless AP mode, also known as the bridge mode.

Tengda how to go to AP mode has it on the manual, you take a look.

Your line is routed out and can no longer be connected to a router, but can only be bridged, using a switch or wireless bridge. Generally, wireless routers have a wireless bridging mode, also known as wireless AP mode. Then connect the network cable from the router to the WLAN port of the router in wireless AP mode to use Wi-Fi.

If you open the router settings page, it will open the settings page of the router that you have in the house.

1.You can open the browser on the computer, enter in the ** bar, enter the router settings interface, click Advanced Settings - Running Status, and see the status of the WAN port.

2.If the WAN port status shows that it is connected or connected, the connection mode is automatically obtained, you first confirm whether the route is not connected, whether the broadband cable directly connected to the computer needs to dial-up the Internet, if necessary, click Advanced Settings - Internet Access Settings on the routing settings interface, change the Internet access mode to ADSL dial-up, and enter the password provided by the broadband.

3.If the WAN port status shows that the connection is in progress, the connection mode is ADSL dial-up, connect the broadband network cable (network cable that can access the Internet) directly to the computer, and then click on the computer desktop "Broadband Connection" to "delete" the "broadband user name and password", re-enter it, and then click Connect to see if it can be connected.

If you can't connect, you need to contact broadband, if you can, connect the broadband line to the routing WAN port, use a network cable, one end to the computer and one end to the routing 1 2 3 interface. Open your computer browser and enter the router settings interface in the ** bar.

Click Advanced Settings-Mac Clone, Manual Clone-Clone Mac Address, and click OK if you see that the address does not start with C8:3A:35. (When cloning, you need to take a network cable to connect the computer to any one of the router 1 2 3 interfaces, do not connect the wireless signal of the router route).

4.If the WAN port status shows that it is not connected, check whether the light of the WAN port of the router is on, if not, you can unplug the line of the WAN port and connect it again.

Click "Advanced Settings" -WAN Rate Control, select 10M half-duplex for bandwidth below 4M, 10M full-duplex for 4-10m, 100M half-duplex for 10M-20M, 100M full-duplex for 20-100M, and click OK. Click on System Tools - Restart Router.