Mercury Infinity Router Connection Problems Ball Advice Rush Rush !!!

There is no connection between the cat and the router, you use a network cable from the cat to the WAN port of the router, and then use another network cable to connect to your computer from either port of the router. Then open the IE access router (address, password, router manual), after entering the interface, there should be a connection wizard on the left, you follow the steps step by step.

1 Connect the network cable from the ADSL to the router.

2 Open the router's manual and follow the instructions step by step.

2 Look at mine without instructions.

3 After connecting to the router, enter in the browser or use that to see if it can be opened, and the username and password are usually admin

4-Point Setup Wizard Set dial-up, broadband username and password, and select PPPoE dial-up method.

5 Turn on the DHCP function of the route, 6 Set the IP and DNS of each computer to be acquired automatically.

7 ok.

Wireless network settings Follow the instructions to turn on the wireless, and then encrypt it, generally using WPE2 encryption.

I'm using fast wireless routing.

Good luck.

When you faint, connect a network cable from the cat to the WAN port of the router, and then use the root network cable to connect from any port on the router to the computer.

The computer should provide a broadband cat (modem), and the broadband cat is directly connected to the computer and dial-up to the Internet.

If you use a wireless router, the connection method is as shown in the figure above: the LAN port of the broadband cat is connected to the WAN port of the wireless router, and the remaining 4 ports are LAN ports, which are connected to wired (such as desktops or laptops), and directly receive wireless signals.

Note: There is a description in the manual of the wireless router:

Every step: the wiring icon.

Step 2: Change your computer's IP settings.

Every 3 steps: Go to the router settings interface and set up the router.

You can set up the router again, and the router setup method is introduced as follows:

Configure the computer IP to be automatically obtained, and connect the incoming line to the WAN port of the router (indicated on the router); Find another network cable plugged into the LAN port (marked on the router) at one end and plugged into the computer at the other end;

1. Log in to the router (turn on your computer, click IE, and enter in the address bar.)

After pressing enter, the login page will pop up and enter the username "admin" and password "admin", please refer to the router user manual for other routers);

2. Click on the network settings on the left and select PPPoE in the WAN port settings

Enter the username and password given by the operator (if you don't know, call broadband customer service), enter the DNS address (you can find your local DNS address on the Internet);

3. Turn on the DHCP server;

4. For the wireless router, turn on the wireless network, turn on the wireless network function, and set the wireless login password (security option wpa-psk wpa2-psk

Enter the key), the SSID broadcast is turned off (but keep in mind the SSID name, and manually enter the SSID name and wireless login password when selecting other when connecting to WiFi in the future);

Save the parameters and it's OK,At this time, the desktop is already available,Then open the wireless network card in the right corner of the desktop to right-click to view the available wireless network,Now your router broadcasts the signal,Double-click to connect,Enter the key to get it。 Wired and wireless access is available.

Configure the IP on the computer to automatically obtain, and in the future, you can go to the Internet by opening the browser directly on the desktop, and finally connect the computer to the network (wired, can be) to check whether you can access the Internet normally.

If you can't access the Internet, you can only connect to the computer that can access the Internet normally after dialing up the link on the router, log in to the router again, and do it in the WAN port settings, and it's OK.

1. The local connection of the computer is set to a fixed IP address.

1. Right-click the connection icon in the lower right corner of the computer and click to open the Network and Sharing Center.

2. Click Wi-Fi connection or local connection, and click Properties.

3. Double-click protocol version 4, check Automatically obtain IP address and Automatically obtain DNS server address, and click OK.

2. Caused by the wrong connection and setting of the wireless router.

1. The broadband network cable is connected to the WAN port of the router, and the computer is connected to the wireless router through the wireless network card.

2. Open the browser and enter the address of the router, and then press Enter.

3. Enter the administrator password and press OK.

4. Click the setup wizard, click Next, select the PPPoE (ADSL virtual dial-up) Internet access method, click Next, enter the broadband Internet account and password, and click Next.

5. Enter the SSID name, click WPA-PSK WPA2=PSK, set the PSK password, and click Next.

6. After the router settings are complete, click Save, and then restart the router.

3. The broadband Internet access account and password entered by the router are incorrect.

Call ** to the broadband company, check whether there is a problem with the service provider's terminal, query the broadband Internet account and password, and the service provider can send it by SMS to verify the correctness.

Question: I'm an Apple computer.

Question 123: Apple does not have.

Answer: First make sure that it is a problem between the Mercury wireless router and broadband; Or is there a problem between the computer and the Mercury Infinity Router, and the judgment is based on whether the WAN port of the Mercury Router has an IP address. How to check the status of the WAN port: Log in directly to the management interface of the Mercury wireless router, and you can directly see whether the WAN port has an IP address under the "Operation Status" option.

Question: The mobile phone can be connected normally, but the computer cannot. Have an IP address. The address is.

If the question is set to a fixed IP address, can I get an IP address automatically? Unable to find blocking settings.

What connection method do you use, PPPoE, static?

What should I do if my router is connected but I can't connect to the Internet?

The router is connected but can't connect to the Internet, what should I do, this method is easy to solve.

Wireless routing settings, please refer to the manual, confirm that the line ports are connected, sometimes restarting the router will solve the problem; Here's how I set it up for your reference, good luck!

Installation settings of various brands of wired routers, wireless routers.

The router needs to be properly connected and set up to access the Internet.

1. The broadband network cable or the network cable out of the cat is connected to the WAN port of the router, and the LAN port is connected to the computer.

2. Enter in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Answer: 1. Set up the dial-up connection according to the requirements of the operator, connect the stand-alone device such as the operator's optical modem, and ping the operator's gateway or DNS server address after dialing up the Internet;

2. If the ping is not working, it means that the operator's external network network is not connected, just call ** to find the operator to report for repair;

3. If the ping means that the external network network is normal, it has nothing to do with the operator's network, and the fault is on the router, restore the router to factory settings, and then reset it to eliminate the fault.

4. If the reset route is still faulty, the router may have a hardware failure and can only be replaced.

Hello! Generally, the router needs to be set up after it has just been bought or reset and restored to factory settings, and only after the correct settings can it be used normally.

In general, there are two ways to access the Internet at home (the "static IP" method, which is rarely used in the home, is omitted here).

Let's talk about the first "dynamic IP" method, which is characterized by the fact that when the router is not used, the network cable can be plugged into the computer to directly access the Internet, and the setting of the router is relatively simple. Here's how:

Disconnect the broadband network cable of the WAN port of the router first;

Then enter the router settings interface through the web browser on the computer (or the browser on the mobile phone);

Then restore your router's WAN port broadband network cable connection;

Succeed. The second "PPPOE broadband dial-up" method is characterized by the fact that when the router is not used, a broadband connection with a username and password is required on the computer. Set the Internet account and password in the router, the router reset is to restore the factory settings, the factory settings are impossible to store your Internet account password, that is to say, after each reset, you must re-enter and save the Internet account and password in the router to work.

Here's how to set it up:

Enter the router: enter the router settings interface through the web browser on the computer (or the browser on the mobile phone), and enter or (this is the default address used by most routers, but please check the nameplate at the bottom of the router or refer to the router user manual for which address);

Find the [Setup Wizard], fill in the pppoe in the Internet mode, click the next step for the others, and then there will be an interface that requires you to fill in the Internet account and password, fill it in truthfully, save the settings, and restart the router to access the Internet;

Succeed. Of course, the above two methods are only the most basic steps to solve the "can access the Internet", in addition, you also need to modify (or not modify) the name of the wireless network (SSID) according to your own needs, as well as choose WPA2 encryption method, and set a wireless password with a length of 8 63 digits for the wireless network.

I hope it can help you, please ask if you need it. It will definitely help you solve the problem.

Did the computer reinstall the system? Take a look at whether the local connection on the computer is normal, if the line is plugged in, the local connection shows that it has been connected and you can view the IP obtained on the local connection, so that you can enter the router settings interface normally, if the local connection is crossed, the network cable is problematic or not plugged in, you can also change the port of the router to try, if there is no connection to the IP of the router, you can restart the router or bind the IP of a router on the local connection, and it may be that the driver of the network card is not installed.

Once the router is properly connected, it needs to be set up correctly before you can surf the Internet.

If your broadband is dial-up connection, the router WAN port will select PPPOE dial-up, fill in the broadband account and broadband password to save the Internet.

This is not set up successfully, it is recommended that you reset the router.

1. You need to connect the router to the computer with a network cable;

2. Enter the IP address of the router on the computer, generally 3. Log in to the router interface, and the login password is lowercase admin;

4. Find the WAN option, select PPPoE in it, and then enter the broadband account number and password to confirm;

5. You can set the wireless network in the wireless network setting option, and enter the SSID is your wifi name, which is encrypted;

6. Click "Restart Router" in the system tools or other options, wait for a while to restart, and then you can surf the Internet.

The IP and routing of the cat at home conflict.

You type admin---admin above

Change the address to.

Then turn off the route and reopen it, OK.

1. Start the setup wizard.

Once you are in the management interface of your router, click on the Setup Wizard, and then click Next.

2. Choose a way to access the Internet.

Select PPPoE (ADSL Virtual Dialing) as the Internet access method and click Next.

3. Enter the Internet broadband account and password.

Enter the broadband account number and password provided by the carrier in the corresponding settings box, and make sure that the account and password are entered correctly.

4. Set wireless parameters.

The SSID is the name of the wireless network (you can set it according to actual needs), select WPA-PSK WPA2-PSK and set the PSK password, click Next.

Note: The wireless password is used to ensure the security of the wireless network and ensure that it is not used by others.

5. The setting is complete.

Click Restart and the setup wizard is complete.