Pulian wireless router domain name login management problem!

Browser login to the router management page, possible IP:

2. Check the gateway in the computer network connection properties.

3. Check the manual, or the logo of the router body.

Is there another route ahead? There is an error in wiring or setting!

Shouldn't the default LAN address of Pulian be? And this should be when connected to the router, the router provides DNS resolution.

TP-Link Wireless Router Cannot Enter the Settings Interface for the Reason:

1. The login address of the router is incorrect;

2. The router is connected incorrectly;

3. The router has a conflict with the modem address;

4. Router failure.

2. Connect the LAN port of the router (generally 4 ports of the same color) with the computer to log in to the router normally;

3. Individual cats have their own addresses, in order to avoid conflicts between the router and it, it is recommended not to connect the cat first, connect the LAN port of the router with the computer first, and then connect the cat after setting the router IP address;

4. Change a router, reset the IP, and connect with the cat.

Method steps.

Check 1: Check whether the line connection is correct.

Check 2: Make sure that the IP address of the computer is obtained automatically.

Check 3: Confirm the login method.

There are two types of routers: domain name login and management IP login, which are as follows:

1. Domain name login.

On the tin mark at the bottom of the router is written "Management Page:, as shown in the figure below:

The page pops up the login dialog:

2. Log in with your IP address.

Note: If the environment is a rental house, community broadband, office LAN, or hotel environment, the router will automatically detect the front-end network and adjust the network segment to avoid IP network segment conflicts. Therefore, when logging in to the management interface with an IP address, be sure to confirm the IPv4 default gateway address that the computer actually obtains.

Troubleshooting 4: Check your browser settings.

Please check your browser settings as follows:

Disable dial-up connection: Open IE browser, click Tools >>Internet Options, select Connections >> never make dial-up connections.

Disable Network**: Click Tools >> Internet Options, select Connect >> LAN settings, make sure none of the three options are checked, and click OK to go back to the previous Internet Options dialog box and click OK. As shown in the figure below:

Turn off offline status: Offline status will affect normal browsing of web pages, click the browser File >> work offline, and make sure that it is checked before offline work.

Once the setup is complete, try to log in to the router management interface.

Check 5: Change your browser or computer.

Change your browser (Firefox, Google Chrome, or another browser) or try to log in to the admin interface on a different computer.

Check the six-reset router.

When the router is powered on, use a paper clip or other pointed object to press and hold the reset button on the back panel of the router for 5-8 seconds, and the indicator light on the front panel flashes three times to become solid on, indicating that the router has been reset successfully. Reference:

The fever will experience the human body and send a picture to it.

1. First of all, try the initial default password of the router, the default password of most routers is: admin, part is: guest, if you are not clear, you can look at the label or manual on the back of the router.

2. If the password is incorrect. Then reset the router. There is a small port on the side of the network cable port of the router, which is the reset button.

The reset button needs to be pressed with a toothpick, needle or refill and other slender things, and you can hold down the reset button for more than 8 seconds, and then you will see all the indicators flash at the same time, indicating that the reload is successful. After the reset, all the settings of the router are restored to the default values, and the login password of the router becomes the initial password.

For TPLink WR886N, perform the following steps:

1. Open the browser, enter the router IP address, press Enter, default is;

2. Enter the router password, click to log in, the default is admin;

3. Click Security Function on the left side - Remote Web Management;

4. The remote management port can be set on the right, click Enable, and the remote web management address can be modified to, click OK.

On the router that needs to be remotely managed, enable remote web login (almost all routers have this option);

If you do not have this function, install the Peanut Shell client program on any computer on the intranet where the router is located, get angry with the Peanut Shell Passport, and log in to activate DDNS.

Then, log in to the router remotely from the control computer, and enter the domain name corresponding to DDNS in the IE address bar to open the web settings interface.

Be careful not to do port mapping on the router being controlled.

1. Log in to the TP-Link wireless router management interface: enter it in the browser, enter the username and password in the pop-up dialog box, and the default is admin.

2. Click "Security Settings" - Firewall Settings - check "Enable Firewall (Firewall Master Switch)" and "Enable Domain Name Filtering" - Save in the pop-up interface on the right.

3. Select Domain Name Filtering and enter Disable**.

This is the password setting of the router, and you have to set it yourself.

If you don't set up others, it's okay to have an opinion.

To be on the safe side, it's not good to be deciphered by someone else.

There are currently two types of login addresses for tp-link routers, and the management addresses may be different for different routers.

The login of the TP Link router is: Some of the earlier router management addresses are the login of the mini router. You can check the information of setting up the network in the manual of the router or the nameplate at the bottom.

The login for older versions of TP-Link routers is:; The login for the new version of the TP-Link router is: The login of the TP-Link Mini Router is: Let's go into more detail:

1. The login of the old version of the TP-Link router** is: The login of the TP-Link Mini Router is: The login for the new version of the TP-Link router is:

1. First of all, we need to connect the TP Link router, and then enter the address of the router through the browser of the mobile phone or computer;

2. After we enter the address and click enter, it will pop up and let us enter the management password, if the account is admin when we use it for the first time, the password will let us define a password by ourselves, and the default password is also admin;

3. After entering the router, we click on the router settings icon option on the right to set it;

4. After we click on the router settings, an interface will pop up, and on the left side of this interface, we select Internet settings;

5. In the Internet settings, we need to enter our wide account and password, and then click Connect to wait for the router to go online.

The default login address of Leike is, if you can't log in, it's because you modified it, and if you forget the modified address and password, then you can only reset: press and hold the reset button for more than 7 seconds after powering on.

To Liu Lanqi Book 12. pω

It glows blue (the main color of the 186 team).