How to judge whether the car is correct or not when the pile is reversed

When the pile is reversed, it is generally seen from the rear of the car. If you look at the rear of the car, the two poles at the back can evenly divide the rear compartment panel, which means that the car is right, otherwise it is not. When the pile is reversed, it is generally not seen from the reflector.

Addendum: There is no fixed rule for this, you should pay attention to correct the direction according to the driving situation of the car at the time of reversing. When reversing, you should look at the rear window from the middle of the car, and then look at the rear compartment panel.

You see that the rear lever enters the two sides of the car about 10-15 cm and then stops, which is just right, neither out of the bottom line, nor far from the bottom line.

If you can't tell where the car is, my advice is to go in the direction a little earlier, and then adjust it on the way. This is my experience. Hope that helps.

Landlord Don't panic Don't imagine it too scary There is a terrible rule for taking a driver's license If you learn well, you will make a mistake If you don't learn well, you can pass... Scold...

In the right rear window, the center rod is hit, and the right direction is held;

Guidance on pile reversal and library transfer.

Invert the left library. 1. The center rod in the right rear window is held in the right direction;

2. Partial (left) right less repair, outer (right) left less repair, such as 10 cm outside, left direction half a circle;

3, the right rear corner of the car from the real distance between the rod 20 cm, speed right to the end;

4. (Left hand four points right armchair) the chair is in the back view, when the bottom of the window is in the middle of the left back bar, the left circle direction;

5, two rear rods into the rear window to both sides of the window corner, which side (outside) more to which side to play, and back to the right (or far to find the bottom of the library, and the bottom of the window in alignment), near the bottom (after both sides of the small window exposed two rear rods) parking.

Move the library in. 1. Right to the end, start;

2. The left tendon is on the center of the rod and the speed is left to the end;

3. The left 3 ribs are right back to the right of the center rod speed;

4. Parking near the top of the warehouse.

Move the library and retreat. 1. Right to the end, reversing;

2. When the left hook of the head is on the left side of the rod, the left side is to the end;

3. The front middle rod in the car, and the back middle rod is corrected when looking back;

4. Near-bottom parking.

Feel. I'm just poor.

Introduce several practical methods: When the rear of the vehicle has entered the garage, but the front of the vehicle has not entered the garage, if the body is tilted and the rear of the vehicle is deflected to one side, the steering wheel is positioned too early, or the steering speed is too fast. That is, you will return to the steering wheel before the middle of the finch branch at the rear of the vehicle and the middle of the bottom line of the garage are in a straight line.

When reversing slowly, first observe whether the middle position of the parking space and the middle position of the bottom line of the garage are kept in a straight line through the middle rearview mirror, and the left and right floating range can be within 10cm. If the rubber pin between the two points deviates greatly, it needs to be adjusted by the steering wheel in time to keep the body in the correct position at all times. 2. How to judge the opposite side of the car when reversing?

When the rear of the vehicle has entered the garage, but the front of the vehicle has not entered the garage, the rear of the vehicle deviates from the centerline side. The reason could be that the steering wheel is playing too late or the steering speed is too slow. In other words, when the steering wheel is not perfectly aligned, the middle position of the rear of the vehicle and the middle position of the bottom line of the garage are already in a straight line.

It is also possible to judge whether the body is upright by looking at the rearview mirrors on the left and right sides. The specific method is to observe whether the edge line of the car body is parallel to the garage and whether the distance between the body and the sides is equal. If you find that the vehicles are not parallel, which direction will you turn and which side of the car will be farther away from the sideline?

Slow down and adjust slowly until the two sides are parallel and equidistant.

1. How to judge whether the body is correct or not in reversing introduces several practical methods: when the rear of the vehicle has entered the garage, but the front of the vehicle has not entered the garage, if the body is inclined and the rear of the vehicle is biased to one side, the steering wheel positioning is too early, or the steering speed is too fast. That is, you will return to the steering wheel before the middle position at the rear of the vehicle and the middle position at the bottom line of the garage are in a straight line.

When reversing slowly, first observe whether the middle position of the parking space and the middle position of the bottom line of the garage brigade are maintained in a straight line through the middle rearview mirror, and the left and right floating range can be within 10cm. If the deviation between the two points is large, it is necessary to adjust the beam through the steering wheel in time to keep the body in the correct position at all times. 2. How to judge the body of the car in reverse, when the rear of the vehicle has entered the garage, but the front of the vehicle has not entered the garage, the rear of the vehicle has deviated from the side of the center line.

The reason may be that the steering rubber chain is too late or the steering speed is too slow. In other words, when the steering wheel is not perfectly aligned, the middle position of the rear of the vehicle and the middle position of the bottom line of the garage are already in a straight line. You can also determine if the body is upright by looking at the left and right side mirrors.

The specific method is to observe whether the two sides of the car body are parallel to the edge of the garage, and whether the distance between the car body and the two sides is equal. If the vehicle is found to be not parallel, it will turn in which direction and which side has a greater distance from the sideline from the rear. Slow down and adjust slowly until the sides are parallel and equidistant.

When reversing into storage, if you want to judge whether the body is correct or not, you need to look at the left and right rearview mirrors, and you can observe whether the body is parallel to the side line through the rearview mirror.

The correct way to reverse the banquet into storage:

1. After the vehicle is parked in the appropriate position, hang the reverse gear, and then reverse in a straight line, and then hit the right full direction after reaching the standard point of the right direction.

2. Then observe the right rearview mirror of Hehu, the change of the library angle and the body, less than 30 cm, you need to return the steering wheel to the right, continue to reverse, more than 30 cm do not need to move, you can go back half a circle to continue to reverse.

3. After returning to the right direction, observe the right rearview mirror, the corner of the library and the front door handle, and when the front door handle is to coincide with the corner line of the library, the steering wheel is full to the right.

4. Observe the left rearview mirror, and you need to return to the right direction after the inner library angle appears. After returning to the center, the two sides need to be parallel, and then look at the left rearview mirror, the lower edge of the rearview mirror and the library edge line can be parked on a line.

1. The key elements of the pile pile to see whether the body is correct are: the body in the library should be parallel and equal to the left and right sides, and it should be noted here that the reversing mirror is a slightly convex convex mirror, which is convenient for observing the larger field of view around it, and the parallelism we see is also wide in front and narrow in the back.

2. Look out the window, which side is close to the pole and hit the direction of which side. I think that's how you understand this. That is, the side of the reversing mirror on the left and right sides is close to the pole, or when you want to touch the lever, you can just play in the same direction.

In other words, the left mirror hits the left and the right mirror hits the right. Remember to return to the right direction as soon as the mirror passes the pole, otherwise you will be out of line. After returning to the right direction, the body is fine-tuned and corrected according to the principle of which side is wide and which side is played.

The principle of fine-tuning is simpler, that is, the left is wide and the left is played, the right is wide and the right is played, and then the simpler is when you see the left wide, the right is naturally narrow, at this time the left should be played, on the contrary, the left will be narrow when the right is wide, and the right will be played at this time. When the left and right sides of the body are equal to the bottom line, return to the positive direction and fall straight back.

This is experience, there is no particularly good way, is to look at the reflector, after entering the pile, back to the steering wheel, when retreating, the car retreats in a straight line, just on the line.

1. As for whether the car is correct or not, the most important thing is the "car feeling". I didn't know it on my first day of school. After two days, I will feel almost the same.

2. You can also pass the left and right rearview mirrors to see if the body is parallel to the line. If it is parallel, it is positive.

3. You look at the body on both sides through the left and right rearview mirrors, which side is close to the line, and which side is far away. And then which side of the line is wide to which side to hit the direction...

The rear-view mirrors on the left and right sides of the body show that the body is parallel to the ground line. When reversing, the sideline should always be parallel to the body from the rearview mirror, about 20 cm on both sides, and then constantly adjusted during the reversing process. The adjustment method is to look from the left rearview mirror, if you feel that the distance between the left side of the body is relatively large, the direction is to the left, and then immediately return to the right; If you are close to the sideline, hit the right in the direction and return to the right immediately.

In short, the distance over there is a general direction to hit that side.

1. Before reversing, first see the situation behind the car, estimate the route of reversing, and determine the process of reversing.

Don't go too fast.

2. Turn the steering wheel with your left hand according to the direction of travel at the rear of the car: if the rear of the car needs to go to the right rear.

in, then turn the steering wheel to the right; Otherwise, turn the steering wheel to the left. Actually, this and the car drove forward.

The steering operation is the same, so you won't get in a hurry if you get the wrong direction.

3. Don't keep looking at the back of the car during the reversing process, and on the premise of confirming the safety behind the car, you need to do it from time to time.

Observe the left and right mirrors, pay attention to the distance between the obstacle and the vehicle, and use the steering wheel to correct the rear of the vehicle accordingly.

The position of the setback.

4. If you feel that in the process of reversing, the front of the car may hit obstacles, you also need to be at the appropriate time.

Look in front of the car so that the front of the car does not hit obstacles. Especially in the case of a large amplitude of steering wheel turning, by.

In the process of steering, the turning radius of the steering wheels is greater than that of the rear wheels, and the head of the car is reversed.

The amplitude of the throw outward is also large, so be sure to pay attention to the front of the car to avoid rubbing. This method stops the vehicle on the right side.

It is more suitable for cars and when you need to reverse for longer distances. In addition, it is necessary to avoid unfamiliar terrain and surroundings at night.

Reversing in environments such as narrow spaces and poor lighting. Poor lighting at night, blurred line of sight, and mastery of the scale of the surrounding space.

It is not allowed to wait, it will increase the difficulty of reversing, especially the difficulty of the vehicle with the film, so you should try to choose good lighting.

Well, the surrounding space is spacious, flat place to reverse, and the reversing distance should not be too long, it is best to avoid or reduce.

Reversing at night.

The main judgment methods are:

If you look at the right side mirror, you can see that the right door handle is flush with the sideline.

Look at the left rearview mirror, the left door handle is a certain distance from the sideline, just keep it parallel.

Isn't this looking in the rearview mirror? See if the door is parallel to the line on the ground, and then look at the left and right rearview mirrors to see if the distance between the two sides is about the same... If the distance between the two sides is about the same, and it is parallel to the line, it is right. I really can't get out of the car and take a look.

The car starts from the starting point, step 1: hang the reverse gear, reverse the car with straight shoulders, look sideways to the right, and stop from when the two large pillars in the front and rear of the outermost side of the garage are parallel. Point to the outside of the column.

Step 2: Hit the right direction, backwards, look back, when the small pillar in the middle appears in the rear glass, stop immediately, hit the direction right, fall backwards, when the small pillar in the middle disappears, kill to the right again, and fall backwards. If the middle pillar appears in the back glass, use the previous method again.

But if your rear glass doesn't appear at the beginning, it means that you can reverse the car to stop when you look at the rear end of the wheel from the rearview mirror and not next to the yellow line. Step 3: Move the library, hang the forward gear, hit the direction to the right, stop immediately when the left corner of the front car glass is just over the small pillar in the middle, and stop the car when the car is not next to the small pillar in the middle.

Hang in reverse again, hit the direction to the right, reverse the car, look in the left rearview mirror, stop when the left wheel is next to the yellow line, and then hit the direction to the left and straighten the car. Forward one meter five, then backward, and then half of the direction, to the left of the warehouse, when the left front car corner against the left side of the warehouse on the pillar, and then the steering wheel back to the right, out of the library. When the wheels of the car are 50 cm away from the yellow line, stop, hit the direction to the left, and stop when the car is straightened.

Step 4: Reverse the car and look sideways to the left, stopping from the outermost side of the garage when the two large pillars in front and rear are parallel. Point to the outside of the column.

Go left and fall backwards, and stop when the car is parallel to the yellow line. Go backwards and stop when the entire car is in storage. Exam Complete!

What car did you test, Jetta? Santana? ZTE? Pickup? Cart? Bus?

I'll give you a **, you go online and take a look I hope it will be useful to you.

Dude, I've been through this issue before, so I think I should have a say in this. Thank you!

I don't think it's right because you haven't found the feeling yet. The so-called feeling is: to focus on the overall operation of the vehicle, do not aim at a certain pole and a certain line; For example, if you look at the mirrors on the left and right sides of the car and reverse the car, then you should absolutely understand the overall operation status of the front and rear of the car when the steering wheel is left and right.

When the steering wheel is left, the rear corner of the car goes to the left, and at this time, it should be noted that the front of the car is just the opposite to the right. The right-hand direction reverses the law, that is, the right-hand direction, the tail angle to the right, and the front to the left. To put it more bluntly, when you are reversing and you see the front of the car going to the left, you need to know that the rear of the car will go to the right, and when the front of the car goes to the right, the rear of the car will go to the left.

There is also room for adjustment in the pile: it is best not to slam the steering wheel too much, to hit less and return less, play fast - wait - fast back is better, and it is better not to hit the steering wheel more than one lap. Then there is when the rear wheel just enters the bar, immediately move the eye to the back two rods, or the parallel lines on both sides, so that it is easy to turn the car right.

It's also important to learn how to use mirrors really effectively.

Oh, that's all there is to it, if you don't understand, ask me.