The heating tube of Joyoung soymilk machine is blackened, and can it still be used if the heating tu

Joyoung heating tube is made of 304 stainless steel, the arc under the heating tube is blackened, you use the steel wool ball to brush it off, but the pulping time will be there for a long time, and the impact is not great. Hello, the preliminary conclusion of the machine paste pot, paste pot general machine no problem, can still be used with confidence, generally because the cup or heating pipe is not cleaned, or the material is added too much or not suitable, you can use the steel wool ball to clean up the material residue after soaking, and then clean it.

You may not have cleaned the heating tube thoroughly after the first use, and the second time you used the heating tube to directly scorch the residue (soybean milk) from the last time to form the heating tube to turn black. Another possibility is to use a soymilk machine to beat mung beans, because mung beans have a higher starch content, which can make the heating tube black.

Two situations: 1. The residue of the last time was not cleaned, resulting in direct charring during the second use;

2. If there is a quality problem, take it and replace it.

After making soy milk, it should be cleaned in time. If it were **, this would not normally happen so soon.

It is recommended that you buy some lemons, cut them into small spots and put water in the machine to boil, and then scrub them with a scouring pad, it will be better.

It may be fake, the Joyoung I bought did not have such a situation, the heating tube is stainless steel, this situation should not occur.

The heating tube is not stainless steel, but stainless iron! You try it with a magnet and it should be sucked.

Hawthorn slices, orange peel, rub it off, cleaning silk (plastic kind) smear Mr. Vermeer scrub.

It may be because you didn't clean it first, and it's too thick, it's nothing, regular Jiuyang machine, just take the steel wool ball and pull it,

I've also run into this problem, you can apply toothpaste, wash it with a cleaning pad, and you're good to go.

Works; Generally speaking, the surface of the heating pipe is made of stainless steel, so the corrosion resistance is relatively good. If the heating tube is burned, you can try to dispose of it as follows:

1.Confirm that the heating wire is not burned out.

2.In a container, add the vinegar until it has overflowed the heating tube.

3.Turn on the heating function, and when the vinegar is heated to more than 40°C (your hands feel a little hot), stop heating.

4.After it cools naturally, scrub it with a scouring pad and wash it vertically.

The soymilk machine heats the tube paste tube because of the problem of the ratio of rice to water, everything will smoke when it is pasted, it doesn't matter, the pipe is soaked for a while, and the steel wool ball can be brushed clean with a little force, if it can be heated normally, it will not affect the use if it is blackened.

Common faults of soymilk machine.

It's not completely broken.

The soymilk made by the soymilk machine is not broken with particles, and it is very likely that the side net or bottom mesh of the mesh cover is blocked, resulting in the problem that the soymilk is relatively large in size, at this time, it is necessary to disassemble the soymilk machine, re-brush the mesh with a cleaning brush, and then press it back again, so as to solve the problem that the mesh is blocked and cannot continue to work. In order to avoid similar failures in the future, remember to clean the soymilk machine after each use.

Burned. This problem has a direct impact on the fact that the heating tube of the soymilk machine is not thoroughly cleaned, and it is recommended that the heating tube can be removed and cleaned again at this time, which can effectively reduce the problem of soybean milk burning. Also pay close attention to whether the heating pipe is damaged, if it is damaged, it can be replaced in time.

There is a warning that soy milk is not cooked.

There are two main reasons for this problem, it may be that there is a quality problem in the soymilk machine itself, and it has the risk of delayed judgment safety prompts; It is also possible that the daily operation is not quite correct, such as adding too much water to exceed the load of the soymilk machine, so that it cannot continue to complete its work, etc., you can use the elimination method to determine which is the reason.

When the soymilk machine is in use, it must be at a certain distance from the socket and other items, so that the plug is in a position that can be reached, and it must have good grounding. At the same time, it is also necessary to keep a safe distance from flammable and explosive items. In the process of using the soymilk machine, each function key of it must be pressed by installing the instruction manual, and the corresponding function program must be selected, so as not to affect the production of soymilk.

Common faults of soymilk machine and treatment methods.

1. Failure phenomenon of soymilk machine: the failure of beans to break is a phenomenon caused by a small failure of the soymilk machine. In the event of this kind of failure, it is generally necessary to consider that there is a problem with the filter screen of the soymilk machine.

Solution: If the mesh on the side of the mesh cover or the bottom mesh is dry and blocked, then there will be problems such as rough soymilk and large particles of soymilk made by the soymilk machine. This is to disassemble the soymilk machine, immerse the net cover in boiling water and add dish soap, soak for about 15 minutes and scrub it with a cleaning brush.

Most of these failures are caused by users who do not clean the soymilk machine when they usually use it. Second, the fault phenomenon of soymilk machine: the solution to the burnt failure:

When the soymilk machine burns paste, it may be that the heating pipe of the soymilk machine is cleaned, and the heating pipe of the soymilk machine needs to be cleaned. In addition, using mung beans alone to make soy milk may also cause such a failure, so it is best to add peanuts or soybeans to mix it together to solve this problem. 3. Fault phenomenon of soymilk machine:

In the process of making soybean milk, the benefits of soy milk are everywhere, which is more common, mainly due to the following reasons: 1. The mesh of the mesh is blocked, and the treatment method: clean the mesh.

2. The anti-overflow electrode is not cleaned, and the treatment method: clean the anti-overflow electrode. 3. Add too much water, treatment method:

**Between the water and the upper and lower water lines. Fourth, the failure phenomenon of soymilk machine: undercooked, alarm failure in advance.

Solution: In addition to the problem of the soymilk machine itself, such a failure may also be caused by incorrect operation. For example, if the beans have been soaked in water for too long and have deteriorated, the safety identification function of the soymilk machine itself will send out a safety alarm function to remind the user.

Or due to adding too much water, the load of the soymilk machine is exceeded, making the soymilk machine unable to work. Therefore, when using the soymilk machine, it is best to add water between the upper and lower water lines so that the soymilk machine can operate normally. Additional Information:

Precautions for the use of soymilk machine 1, when the soymilk machine is operating, do not forget to install the Rafal net, otherwise the machine will overflow during the beating process to prevent splashing and hurting people, and when making soymilk, you must pay attention to safety. 2. If the machine has a power outage during the operation, and the soymilk machine is in the period from the beginning of the pulping to the end of the operation, do not press the function key to carry out the operation, otherwise it will cause the heater to paste the pipe, and when the soybean milk is beaten, it will simply cause the soybean milk to splash or the machine to beep for a long time. 3. When making soybean milk, please put beans or other raw materials into the cup first, then increase the amount of water, and add water to the upper and lower water lines.

4. When putting beans and rice into the cup, pay attention to placing them evenly at the bottom of the cup as much as possible to prevent the soymilk machine from grinding unevenly, which will eventually affect the taste. 5. The soymilk machine uses a high-speed motor, and when it is destroyed, it will show an intermittent fast and slow sound, which is a common phenomenon.

Answer: Joyoung soybean milk machine common faults, sometimes the motor does not rotate, broken repair can not be repaired.

Let's take a look at the display status of the product screen

1) The function light is always on, indicating that the function of the machine has been started, the first 6-10 minutes are in the heating, after the heating is completed, it will be beaten, you can wait for a while to see the effect, if you have waited for 15 minutes and do not heat, you need to confirm whether the amount of water is correctly added to the highest and lowest between the two water lines.

2) The screen has a long countdown display, which means that the appointment is pressed, the product will not work at the beginning, if you want to make or cancel the appointment directly, you can power off and wait for 1 minute before re-powering, and press to start immediately after selecting the function to observe the effect.

Summary. Extended information: Can the heating rod of the soymilk maker still be used if it is black 75 can be used, black is sediment.

The soymilk machine adopts microcomputer control to realize the full automation of the preheating, beating, boiling and delayed boiling process, especially due to the addition of the "simmering" processing program, so that the soymilk is more nutritious and the taste is more fragrant. The body of the cup resembles a huge teacup, with a handle and a spout, and is mainly used to hold water or soy milk. Some cups are made of plastic and some are made of stainless steel, but they are all made of stainless steel or polycarbonate that meet food hygiene standards.

When purchasing the machine, it is advisable to choose a stainless steel cup body, mainly for easy cleaning. The "water level" line and the "water level" line are marked on the cup body to standardize the amount of water added to the cup. The upper edge of the cup body just fits the lower cover of the machine head, which plays a fixed and supporting role for the machine head.

Kiss Hello thank you Xing sedan you shouted waiting for the group I am very happy to answer your questions The heating rod of the soymilk machine can still be used if it is black, black is sediment.

If it can work normally, it can be used, because this kind of black is caused by the carbonization of the sugar substances under the condition that the temperature of the heater is too high and the water is short, and it will not produce the high loss of cherry blossoms. Also, be sure to pay attention to safety before using it.

The blackening is mainly due to the envy of a few points: 1. The natural color of colored soybean milk is precipitated; 2. There is okara residue in the cleaning process; 3. The starch content is too high in the pulping process. As long as we use a cleaning block or steel wool ball to clean and disassemble the heating pipe and wash it thoroughly, it will be used normally

Cleaning method: 1. You can use warm water and vinegar to clean, if the effect of Qinghe Luguo is not obvious, it is estimated that the proportion of vinegar is too low, you can add more vinegar, soak for 2-3 minutes before washing. 2. You can try to use hydrochloric acid, but please wear rubber gloves when using hydrochloric acid, hydrochloric acid is more choking, don't pour too much, hydrochloric acid has strong penetrating power, you must be careful when using it.

3. Or go to the service outlets of the soymilk machine and let the professionals help clean it.

Extended information: Can the heating rod of the soymilk maker still be used if it is black 75 can be used, black is sediment. The soymilk machine adopts microcomputer control to realize the full automation of the preheating, beating, boiling and delayed boiling process, especially due to the addition of the "simmering" processing program, so that the soymilk is more nutritious and the taste is more fragrant.

The body of the cup resembles a huge teacup, with a handle and a spout, and is mainly used to hold water or soy milk. Some cups are made of plastic, some are made of stainless steel, but they are all made of stainless steel or polycarbonate that meet food hygiene standards. When purchasing the machine, it is advisable to choose a stainless steel cup body, mainly for easy cleaning.

The "water level" line and the "water level" line are marked on the cup body to standardize the amount of water added to the cup. The upper edge of the liquid in the cup hall is just wide to cover the lower cover of the machine head, which plays a fixed and supporting role for the machine head.

Summary. Hello, the heating rod of the soymilk machine is black, of course it can be used continuously.

Hello, the heating rod of the soymilk machine is black, of course it can be used continuously.

The heating rod of the soymilk machine is black, because long-term use has caused a chemical reaction between the sediment itself and the soymilk machine, which causes the heating rod to turn black.

For a soymilk machine, it is normal for the heating rod to be hacked, and there is no hardware damage.

It also does not affect your normal use at all.

Therefore, for your question, the heating rod of the soymilk machine can be used when it turns black, and it will not affect the normal use of food by the wheel of the empty wheel, which is also healthy, and the machine itself is also safe.

So you can rest assured.

What to do if soy milk has a mushy taste.

Does soy milk have a mushy taste? It depends on how long you make soy milk.

You control the time, and naturally there is no such problem.

But if there is such a situation for a long time.

Then it can be considered that it is the hardware damage inside, which causes the power to not exceed the rated power, which leads to this situation in soybean milk.

I wiped the heating tube with a steel wool ball, can the temperature be adjusted? I wait until 100 degrees, you can see if there is a button to directly adjust the temperature outside your soymilk machine, if there is no such button, then your soymilk maker is fully automatic.

In this case, there is no way to adjust the temperature directly.

It is not recommended that you do this if the steel wool ball rubs the heating tube, as it may cause damage to the film in its shape.

But once or twice once in a while is not a big problem.

It's not tuned, it's automatic.

If it is automatic, it is not possible to directly adjust the temperature, in fact, most soymilk machines cannot directly adjust the temperature.

It is fully automatic in itself, and if there is a scorching situation for a long time.

It should be considered that it is the hardware reason of the soymilk machine itself.

Ask what to do if the heating pipe steel wool ball is wiped and the soy milk is pasted.

After you wiped the steel wool ball, his soy milk was pasted and I had already told you, if it wasn't for the occasional Biyan that was always like this twice, Huidong was either the cause of the influence, or the heating rod coating was damaged.

Either it is the hardware cause of the dust, or the heating rod coating is damaged, if the brother Bojia Boxiang hot rod coating is damaged, it is impossible to effectively control its temperature, which will naturally lead to its paste.