Haier washing machine does not spin dry, prompting how to remove it

What's the situation, it's not running when it's time to spin dry? Or do you have three words on the screen that say "don't spin dry"? Or is there an error**? What is it?

Cause. 1. Unbalanced clothing. When the washing cannot be adjusted to balance, the washing machine automatically sets a low speed, at which the dehydration effect is slightly worse.

Cause. Second, the switch of the top cover is damaged. The washing machine is not allowed to open the top cover because it is a high-speed action when spinning, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the lid is opened. If it is damaged and dehydrated, it will not move!

Cause. 3. The reason for the material of clothing. It is recommended to use high-speed dehydration for washing products with strong water absorption (high-speed dehydration cannot be used for some high-end clothes).

Cause. Fourth, the drainage system is blocked. The washing liquid in the water cylinder can not be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch can not be reset, and the washing machine can not enter the dehydration program.

Cause. 5. The water level switch cannot be reset. The dewatering process of Haier washing machines starts when the water level switch is reset after the washing liquid has been drained.

If the drain level switch is damaged, dewatering is a procedure that needs to be carried out after draining, and if the water level switch is damaged, the dewatering procedure will not be entered.

Solution: 1. First check the safety switch, Haier washing machine is turned on and the program is adjusted to the dehydration state, press the safety switch brake arm to the lowest with your hands or tools, if the computer board alarms and the digital tube displays, the safety switch or computer board should be replaced at this time;

2. If the brake arm of the safety switch can be dehydrated normally after pressing it with hands or tools, it means that the power-off distance of the safety switch is low, and the safety switch should be replaced at this time;

3. If in the dehydration state, only the wave wheel rotates and the inner barrel does not rotate, at this time, the tractor should be checked whether the clutch pawl and ratchet wheel have been separated, if not, it is possible that the adjustment rod nut on the drain valve is loose and worn, resulting in insufficient opening distance, at this time, the distance of the adjustment rod should be readjusted, so that the pawl and ratchet of the clutch can be separated.

Summary. 1.Check whether the lid is well coveredIf the washing machine is not dehydrated or dried when used, first check whether the lid of the washing machine is covered, if it is not covered, it will lead to poor contact of the travel switch inside the washing machine, so that the dehydration cannot be completed smoothly.

2.Check the safety switch to turn on the power of the washing machine, adjust to the dehydration state, we can adjust the safety switch to the lowest with hands or tools, see if the washing machine display panel shows E1, if there is an E1 failure**, then you need to replace the safety switch of the washing machine. 3.

Check the dehydration status If the washing machine is in the dehydration state, there is only the wave wheel of the washing machine, but the barrel in the washing machine does not rotate, then it is necessary to check the tractor to see if the clutch pawl and ratchet are separated. If there is a problem, you need to find a professional maintenance personnel to repair it.

1.Check whether the lid is well covered, if the washing machine is not dehydrated when it is used, it is not spun off, first of all, check whether the lid of the washing machine is covered, if it is not covered, it will lead to poor contact of the travel switch inside the washing machine, and the rubber can not successfully complete the dehydration. 2.

Check the safety switch to turn on the power of the washing beam early erection machine, adjust to the dehydration state, we can adjust the safety switch to the lowest with hands or tools, and see if E1 is displayed on the display panel of the washing machine, if there is an E1 failure**, then you need to replace the safety switch of the washing machine. 3.Check the dehydration status If the washing machine is in the dehydration state, there is only the wave wheel of the washing machine, but the barrel in the washing machine does not rotate, then it is necessary to check the tractor to see if the clutch pawl and ratchet are separated.

If there is a problem, you need to find a professional maintenance personnel to repair it.

The screen shows that it does not dry, how to remove it.

The drum washing machine may be in the wrinkle removal mode, so it is free of dehydration, you can adjust the mode of the washing machine, you can also adjust the speed to cancel the non-dehydration mode, or you can directly press the non-dehydration button. In addition, you can also check whether the hail is the cause of the residue filter, the residue filter is used to filter the residual garbage of the washing in the town, and it should be cleaned frequently, and the machine will not be able to drain and dehydrate normally if it is not cleaned for a long time.

1. The safety switch on the top cover of the washing machine is damaged. 2. The washing machine is not spun dry due to foreign objects. 3. Do not spin dry caused by motor failure, 4. Do not spin dry caused by solenoid valve damage.

1. The safety switch on the top cover of the washing machine is damaged. If the washing machine forcibly opens the top cover when drying clothes, the dehydration process will stop immediately, in fact, if the safety switch of the top cover of the washing machine is damaged, it can also correct the washing machine can not be shaken dry.

2. Foreign objects are stuck. The washing machine can not be carried out, there may be a foreign body stuck between the inner and outer barrels, you can open the door cover, turn the inner barrel by hand, if it can be rotated, it means that there is no foreign matter, on the contrary, there are foreign objects, clear.

3. Motor failure. After the power is turned on, if the speed of the electric lift motor is low or does not rotate, it is a motor failure, and the motor should be repaired or replaced. If there is a humming sound that does not rotate, it means that the motor is short-circuited or damaged from turn to turn, or the capacitor is not connected to the motor circuit.

At this time, cut off the power supply, remove the motor belt and restart it on the hail can.

4. Damage to the solenoid valve is a common reason why the washing machine spinning program does not work. The rotation of the inner barrel of the washing machine is completed by converting the gear at the bottom of the solenoid valve, if this part is broken, the washing machine can not be shaken dry, and the solenoid valve can be replaced.

1. It may be because the capacitance of the washing machine is damaged or the electric capacity is reduced, when there is a problem with the electric capacity of the washing machine, especially if some washing machines have been used for a long time, the capacitance is reduced a lot, the strength driven by the washing machine belt is reduced, and the dehydration of the drum is relatively slow, which will lead to the situation that it is not easy to dry the clothes. 2. It may be because of foreign objects at the water outlet, when there is a foreign body at the water outlet of the washing machine is blocked, the water discharged by the washing machine is not easy to flow out through the drain, so the clothes in the washing machine drum must have water retention.

Suggested Solution:

If it is because of the capacitance problem, please buy the same capacity and more than 450V capacitor to replace, replace it with a new capacitor If you know that the capacitor is broken, you can also replace it, and the capacitor electronics market has to buy the same capacitance capacitor, and pay attention to the high withstand voltage value.

If it is a foreign object at the outlet, you need to loosen the hoop that fastens the drain pipe at the outlet of the drain valve, and remove the drain pipe to dredge it.

If the belt is too loose, you need to loosen the fixing screws of the motor base, so that the motor base moves to the appropriate position along the long hole of the screw, and the screws can be tightened.

If it is because of the clutch, you need to replace the torsion spring or clutch.

If it is because of the automatic protection function, you don't need to worry about it, just dry it naturally.