The cat can connect to the network and cannot be connected to the router!!! 100 points

The IP address of a general route is as follows.

You enter and then set your login and password on the page.

Then set your computer's gateway to either of your own IPs. Just OK or IP address. The IP address of the cat and the router is different.

If you connect the router, there is the instruction manual itself to give you the IP of one of the routersLog in to this IP with a web pageYou need to change the IP address to the IP of the router

Oooh. Then you also need to change the WAN interface to PPOE.

You need to set the IP of the first WAN side on the router, and you need to set it to be the same network segment as your cat's LAN IP, or set it to DHCP

So the first thing is to set up your router and the cat connection is no problem. That is, they can ping each other.

Set it up according to the manual, and you don't need to enter the password to log in directly.

Generally, you can't use a router to share the Internet access between two computers at the same time. Because service providers generally restrict the use of routing.

But there are routes that break the restrictions, such as the routes of the Winet, which have special dial-up patterns. You can fool the service provider.

You right-click on Properties in Online Neighbors.

Then click on the right-click attribute in the local connection (see**) to automatically get the IP and try it.

If you are a telecom e-home user, it will be easy to do, run to the telecom business hall, ask him for your sub-account and password, and tell him that you want to access the Internet on multiple machines, without any fees, and there is no need to bother to crack.

The modem or home network cable is connected to the WAN port of the router, and the other computers are connected to the LAN port of the router.

The computer network card is changed to manually set the IP address, mask, gateway and DNS (the default IP range of the corresponding route, the last digit is 2 254 free arbitrary number,).

Enter the default IP address of the route in the browser to go to the route settings page.

Set the account and password for broadband Internet access as a router, set the Internet access mode as "PPPOE", and set the gateway and primary and secondary DNS domain name service names.

Turn on the wireless function and set the wireless key.

When the DHCP function is enabled, you can assign IP ranges, gateways, and primary and secondary DNS

DNS varies from service provider to region to region, so check the local broadband customer service or go online for specific parameters. ）

After this is set up, both computers and wireless devices can automatically obtain IP and surf the Internet.

If DHCP is not enabled in the router, the computer and wireless device need to manually set the IP address, mask, gateway, and DNS to access the Internet.

Even if DHCP is enabled for automatic IP assignment on the router, it is recommended that the computer manually set the relevant IP parameters, which will not only speed up the boot speed, but also speed up the connection to the network and stabilize the network quality.

Reset the router to factory settings, reconnect to the router management page, and enter the account and password correctly in the PPPoe --- the setup wizard until the last step is completed and the router is restarted.

Note: If you can't dial it up, it must be a problem with the account password, you can create a new notepad on the desktop when entering, enter the account password to ensure that it is correct, and then copy and paste it in pppoe.

The router should be set up, according to the manual, set up the route automatic dial-up connection moden to access the Internet normally, if it is adsl, press the pppoe setting to set it all the way, enter your account and password for surfing the Internet, if not, there is a problem with the router, and you can change to a new router.

Connect your router to the Internet before you can access it.

1. Cat Wired Router Wireless router setup is very complicated. Noobs do not recommend such a connection.

1.Disconnect the wireless and wired routers first (it's important not to disconnect if you don't).

2.Connect the wireless router TP-Link using a wired or wireless connection

tl-wr841n

DHCP server -> Not enabled -> Save.

System Tools ->> Restart the router.

3.The wireless LAN port is connected to the wired LAN port.

Description: 1) The default settings of tp-link.

Login is, turn on DHCP, so you have to change the LAN port IP of one of them to avoid conflicts.

2) The wireless router is only equivalent to a switch at this time, and we need to get the IP address from the wired router, so the DHCP of the wireless router should be turned off. This allows you to get the IP address directly from the wired router.

3) You need to use it when you want to log in to the wireless router in the future.

Second, the simple way is: the cat directly connects to the wireless router, and you also need the ISP service provider (that is, the network operator) to loosen your network card, rebind your wireless router network card, and enter your password in the no-bright family router to connect, so that your wireless router can have a network signal.

Hope it helps!

1. First of all, confirm that when you use the cat to dial up the Internet, do you choose the PPPOE mode?

2. When replacing the dial-up connection with a router, is the network cable between the router and the modem checked? When I try to replace three routes, have the network cables connected between the routers and the modem been changed? To rule out the cause of the network cable, the interface is not in good contact or something.

When the routing equipment is replaced, whether the power supply supporting the router is replaced together, or the same power supply is used without matching the power supply with other routes! If you don't have a power supply, try replacing the routing power supply! There could be a power supply issue!

4. It is recommended to borrow a friend's normal route to test, because although the probability of 3 routes having problems at the same time is small, it is not impossible, so the reason for the route itself should be completely ruled out!

After trying the above 4 articles, I can't contact me again, so much can I think of so far!

By the way, is your cat a routing cat? When you go online on the Internet, you can go directly to the Internet, or you can dial up to get on, this is very important! Because if it's a routing modem, and the computer can directly access the Internet when you connect directly to the computer, then your routing modem will turn on the routing function, and then the routing you install yourself will be useless.

Eliminate the above problems, I hope you solve it soon.

Set up your router separately first,Remember that it is alone,That is, the computer is only connected to the router,The router does not connect the network cable of the cat,Log in and change the login address of the router LAN port to change,Then the WAN port configuration is not to be talked about,There is a MAC clone below,Click it,So that the network card address of the computer cloned by the router is gone。 I won't talk about other settings.

If you use a router, the computer does not need to dial up again, and the router has already completed the step of dialing up the Internet for you.

After filling in the broadband account name and password in the router, you don't need to use the broadband connection anymore In the settings of your WAN port, special dialing: change the dialing mode, try one by one to make sure your network cable is okay, especially the network cable connecting the cat and the router to convert the broadband account.

Clone the MAC of the computer to the router and restore the router to its factory value (only connect the router and the computer).

Please try one by one, don't add QQ to you remotely.

This question is very difficult, you have basically tried all the methods you can try;

The technician came to see it, and the cat and the router were also changed, so it didn't solve the problem;

I can only suspect that there is a problem with the network given to you by your network ** provider, and only one computer is allowed to dial up the Internet, and multiple computers are prohibited from accessing the Internet.

This is indeed a difficult question, can you ensure that your broadband username and password are capitalized correctly? Because in many cases, it is not possible to obtain the IP parameters of the operator because the capitalization is incorrect. I don't know what kind of network your external network is, if it is optical fiber, it is recommended that you change the WAN interface network mode to automatic connection and give it a try.

The two will clash at the same time, and this kind of problem has arisen in our company before.

Is the IP address used on your computer static or dynamically acquired?

If the router is not set up, re-set the wireless router, and the broadband modem is connected to the wireless router. Set up, install, and install it like this:

1. Plug in the wireless router and don't pick up the cat first.

2. Reset the wireless router (restore factory settings).

3. Connect the computer to any LAN port of the wireless router, enter the router gateway address (on the label on the back of the router) in the browser address bar, and enter the settings page.

4. Set it according to PPPoE (ADSL virtual dialing).

5. Set the SSID, encryption method and password again.

6. Save and restart.

7. After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

Or, enter the username and password after entering, the username and password are generally admin, enter the dial-up settings and fill in the username and password of the previous Internet access to the dial-up Internet of the router, save and exit, the cat LAN port is connected to the WAN port of the router, the computer is connected to the LAN port of the router, the default setting of the router is to automatically obtain the IP, and the computer is also set to automatically obtain the IP on it!!

Have you set up your router?

The back of the router has the login address, username, and password.

The login address is generally the username and password, most of which are admin, and then fill in the username and password of the previous cat Internet access to the dial-up Internet of the router, and you can access the Internet.

There is also the cable from the cat to connect to the first port of the router, and the rest of the ports are connected to other computers.

The router has to be dialed up, and it can't be connected directly.