How to set up a router at the same time wired and wireless network

First set up a router first, and then pull out a network cable from the port of the first router (if the first one is set as a wired router) to the second router (wireless router), and the 2 positions are reversed, and the setting method is the same! Connect the network cable to the first router, and the interface is different from the other colors! Then connect to the computer and enter it in the browser", or these 2 IPs are the most often used, admim password to come!

Some passwords are blank) If it's not right, just set it up again! If the cat is in your place, you should select the first PPPOE (ADSL Virtual Dialer), then press Next to enter the account number and password (Virtual Dialer), and keep pressing Next on it. Then the router reboot will do it!

There are also computer IPs and DNS, which can be obtained automatically! After setting it up, you still can't access the Internet, just restart the computer! Restart the router, there is a small hole in the back, keep holding it, all the lights in front of it are on together, and it has been restarted!

You can set it up again! Just choose the second dynamic IP, the second router setting is to pull out a network cable from the first router port (4 interfaces of the same color) and connect to the second router, it is the WAN interface (different from other colors), the settings are the same, different from the selection of the second dynamic IP, and then keep the next step OK! That's it!

Multiple routers are connected!

Enter the router settings page, select the PPPoE dial-up method in it, enter the broadband and password, select the "Use the IP and DNS specified by the ISP" in the "Advanced Settings> and enable DHCP in it.

1. First obtain the IP address assigned by the main router.

Connect the main router with a computer, and enter ipconfig all under cmd to view the address assigned by the current master router. In this example, the IPv4 address is ; Default gateway: This is the address of the primary router.

These three digits are the CIDR block, and the addresses available in this CIDR block are. If the CIDR block is, the available address is.

2. Use the IP address and password to log in to the router.

Find the router IP address and username password on the back of the router, and the general IP address is or. Now the new router is not silently recited because of security factors, and the user needs to set the password when logging in for the first time. Now that you're ready, turn on your router and connect to your computer using any of the router's ports.

Use the router address you just found to log in to your router using your browser.

3. Complete the change of LAN port address.

Go to the LAN port settings in Advanced Settings, and modify the LAN port address assigned to the primary router, and the mask address is, in this example, the secondary router address is set to the point after the change, and the router may restart by itself.

4. Continue to set the wireless password.

Select AES as the encryption rule, fill in the Wi-Fi key, and click the OK button.

5. Turn off DHCP.

This step is especially important, because when DHCP is turned off, the secondary router can no longer assign IP addresses, only the primary router can assign IP addresses. Remove the checkmark to enable DHCP and confirm it.

6. Pay attention to the last connection port.

The routing function of the router is removed by the setting method of connecting the router, and only the data ** and wireless functions are retained, so the network cable from the main router can only be connected to the secondary router port, and cannot be connected to the WLAN port (the network cable from the main router can only be connected to the non-WLAN port of the secondary router). And you're done!

The following describes how to set up a wireless router to connect a wireless router to another wireless router

1. How to set up the main router:

1. Plug the network cable (bus) into the WAN port of the wireless router, plug one end of the network cable into any LAN port of the wireless router, and connect the computer network card to turn on the power of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access and password.

5. Save and continue to set the wireless key, (it is recommended to use a combination of numbers and English for the password, and it is best to use the @ symbol in the middle, so as to prevent others from rubbing the net).

6. After saving, you can surf the Internet normally.

7. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

Second, the setting method of the secondary router:

1. Do not connect the secondary router to the main router first.

2. One end of the network cable is connected to any LAN port of the secondary router, and the other end is connected to the computer.

3. Change the LAN port IP of the login interface through the computer browser to avoid conflicts with the IP segment of the main router;

4. WAN port Internet access mode selection: dynamic IP connection, enable DHCP server.

5. Wireless settings and keys, save and exit.

6. Connect a network cable from any LAN port of the main router to the hall belt WAN port of the secondary wireless router, and the computer can access the Internet at this time.

Router A is connected to wireless router B and is connected to the same network segment, and wireless router B needs to be connected as a switch.

Disable the DHCP function of the LAN port of Router B, enable the LAN port setting of network parameters, and change the IP address of the LAN port so that Router B and Router A are on the same network segment. For example, the LAN port IP of router A is changed to B, as long as it does not conflict with other IP addresses that have been used. The WAN port parameters do not need to be set, and the wireless settings of the router are set according to the manual.

1. Set the parameters of the LAN port of the wireless router

2. Wireless router wireless basic settings:

3. Wireless router wireless security settings:

After the setting is complete, the LAN port of route A is connected to the LAN port of route B, and route B is equivalent to the expansion port of route A, which plays the role of a switch, and the computer can be connected to the LAN port of route B. In this way, Router A and Wireless Router B work on the same network segment.

It is recommended to turn off DHCP for wireless transmission.

The routing line is connected to the LAN port and WAN port of the wireless router and is no longer in use.

Use it as a wireless switch.

Set wireless router A as the upper-level route and wireless router B as the lower-level router, and set the settings as follows:

Connect the computer network cable with B first, and don't connect the network cable from A first;

Turn on the computer, enter the B wireless router, change the IP of the LAN to be different from the IP address of the A router), turn off DHCP, and set the wireless connection name and password;

Save the settings and restart.

Connect the computer network cable to A, and connect the LAN port of A to the cat;

Typing in the browser may be something else, marked on the router's nameplate);

Enter your username and password. (The account number and password are marked on the nameplate of the router);

Click "Setup Wizard" in the left navigation pane and click "Next".

Select the "PPPoE" mode and click Next (select according to your broadband type, PPPoE is used as an example).

Enter the broadband account and password (this is the account and password given by the operator when you apply for the network), and click Next;

6.Set the name of the wireless in the SSID; In the PSK password field, enter the wireless password you want to set;

Click Finish to set it up successfully, save it and restart it.

Plug the network cable from A into the LAN port of B to access the Internet.

The landlord is two wireless routers, connected with network cables, set up a secondary route, can also be used as a relay, a route as a router, broadband incoming line connected to the WAN port of the router, with a computer into the router window to set the Internet account password.

Use a network cable to connect from the LAN port of route A to the WAN port of router B, and use a computer to enter the router to change the address of the LAN port to the same as address A, for example (route A is route B, then open the window, and set the WAN port to static IP, that is, route A.

In this way, the network under the two routers is separated.

There's another way.

If you use a network cable to connect from the LAN port of Route A to the LAN port of Route B, turn off the DHCP of Route B so that Route B is used as a switch.

For a wireless router connected by a higher-level wired router, the installation and configuration method is as follows:

1.Connect the wireless router to the higher-level router.

Connect the LAN port of the router with the WAN port of the router, and when the WAN port light flashes on the router, the connection is successful.

2.Connect your computer wirelessly to your router.

The computer searches for the router's wifi name (the default wifi name is located on the nameplate on the back of the router) and connects to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the wireless gateway configuration page.

Open a browser, enter the IP address of the router gateway (usually, the default value is located on the nameplate on the back of the router) to enter the gateway configuration page. (This interface will pop up automatically for new routes).

4.Set up a wireless router to access the Internet.

Go to the WAN port settings in Advanced settings. Select DHCP Auto Acquisition.

5.Set the wifi name and wifi password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key.

6.After the setting is completed, the router will automatically restart, please enter the new wifi password to connect, and you can access the network.

1. Enter the WAN port settings of the TP-Link router: set the Internet access mode here: be sure to remember:

Set the Internet access method to a fixed IP Internet access mode! Remember!! And the fixed IP address is set to the IP address of the LAN port of the router on the third floor!!

Don't make mistakes, otherwise you won't be able to access the Internet. (Premise: The router on the third floor has been set up to access the Internet).

2. Set the IP address of the LAN port of TP-LINK, it is best to set the same network segment as the router on the third floor, and you can turn on DHCP, so that the computer behind can access the Internet without setting, otherwise you have to proceed to the next step.

3. Set the IP of the computer to be in the same network segment as TP-LINK, and the gateway is set to the IP of the LAN port of TP-LINK.

4. Wi-Fi settings: Turn on the Wi-Fi mode, set the Wi-Fi ID, security password and other parameters, and restart the routing. If you're using Wi-Fi, you'll need to set up your computer as well.

Just set it up as required. (The settings of this article can be set according to Help).

Key points: TP-Link must be set to a fixed IP address.

If there is a conflict between IPs, divide the two routes into two network segments. . .

One of the two routers is wired, but the other is not connected by a network cable, how to set it up.

The same setting on the third floor is available.,It's just that the way of access is dynamic.,You don't have to choose **Dial.。

Put the wireless router on the 3rd floor and remove your router.

Haha, you can use it yourself wirelessly, and the signal is super good.

The use of the third floor has wiring by the normal setting.

Use wireless routing on the fifth floor.

The wireless routing from the LAN port of the wireless router connected to the wireless router from the existing line is set as follows.

1.Turn off DHCP

2.Use WPA2 authentication.

3.Assign the management address to another network segment Don't be on the same network segment as the wired router Note: How do you place your wireless router on the third floor The fifth floor may not receive the signal If you don't receive the signal.

You put the router on the fourth or fifth floor, but the network cable might be a little longer.