What do you need to set up on your computer when using both wireless and wired networks?

Wi-Fi can be used at the same time as a wired network, but not within the same network.

For example, you have a 2m network cable at home, and you have a 2m wireless network next door, and you know the password.

In this case, you only need to set the wired network card and wireless network card in the corresponding network IP segment to automatically connect.

But this may not make any sense to you, you can only go from your own home 2m broadband if you want to access the Internet, not the wireless network, only when you access other computers in the wireless network will go to the wireless network, in the enterprise by many such practices.

In many enterprises, for the sake of data security, the ERP system network and the Internet network are separated, the ERP system is wired, and the Internet is wireless.

If your notebook is Lenovo's,Lenovo comes with a flash connection any pass software,You can superimpose multiple wired and wireless networks,I've tried,My own 2m wireless,Three households next door2m,A total of four households,After I use superposition,It can reach 7m**speed。 Of course, the premise is that the next door will tell you the password.

It's a very simple thing,Many people don't like to see a red cross in the lower right corner,Nothing needs to be set,You can click which one you use,If you only use wireless or only limited,Just enter the network neighbor right click to disable。 If you want to use it, right-click to enable.

Load balancing. What to set up? Only there is a wire. The system will automatically take the data from the wire.

Only servers have load balancing.

A host can only use one network, not both.

Wired and wireless network at the same time How to set up:

<>3. After opening, you can see the information of the two network cards, and you can see that the gateway of the wired connection is the external network in the figure), if the wireless connection is connected normally, then you can see the gateway of the wireless connection under the network of the wired connection. Make a note of the gateway to which you connect wirelessly.

For example, if you find out that the intranet gateway is: intranet) know the above information, then tell the computer now that all the networks in this IP segment are connected to the Internet through the intranet gateway.

<>5. Right-click the local connection and select Status.

6. Click Details and remember the IPv4 default gateway, which is in the example figure.

8. Input: route -p add add mask 10After entering, press Enter, and the route table will be added successfully.

The above IP ranges should be added according to the company's network information) After the IP ranges are added, the addresses of all IP ranges will be accessed according to the specified route table, and there is no need to manually switch.

10. Enter: route print command to see the route table that has been added.

If you find that the company's new intranet network cannot be added to the route, you can go to step 10 to check whether the new network has not been added to the routing table. If you don't have to re-add it through Part 8, you can do it.

1. Right-click the network icon on the desktop of the win10 system, and select "Attribute Macro Dry Bi Macro Dry Bi", as shown in the figure below.

2. In the Network and Sharing Center window, click "Set up a new connection or network" as shown in the image below.

3. Select "Connect to Internet" in the Settings Network or Network dialog box, and then click Next, as shown in the figure below.

4. Click Set up a new connection in the Connect to Internet window, as shown in the figure below.

5. Then select "Broadband PPPoE", as shown in the following figure.

6. Finally enter the ISP information provided by the Internet service provider, both and the password. Then Defeat Qing clicks "Connect", as shown in the figure below.

7. After clicking on the link, the system prompts that your Internet connection is being created, wait a while, and the broadband connection will be set.

Once connected, the Network & Sharing Center will display the wired network you just set up.

8. After the broadband connection is successfully created, you can see the broadband connection icon we just created in the network connection, right-click on the broadband connection, and select "Create shortcut" to facilitate us to quickly connect to the Internet in the future. This is shown in the figure below.

<>2. On the page of the control panel, click on the option to open network and Internet.

3. Next, open the network sharing Shouling Center.

4. Find the option to change the adapter on the left side of the tethering center and click on it.

5. You can see the network connection of the computer at this time.

6. When you confirm that there is no wired network connection, click the combination of fn + f2 on the laptop to disable the wireless network. Then you can touch the gods and connect to the wired network.

No, you don't. Plug the network cable directly into the router, and you can use it after debugging.

You can debug your router by following these steps:

1. First of all, we need to connect the cat and the wireless router together. The network cable is first connected to the LAN on the modem, and the other end is connected to the WAN on the wireless router.

2. My computer system XP, take XP as an example, the steps of win7 are the same, one is a local connection, one is an online neighbor, this is still easier to distinguish. First, click on Local Connections and then right-click on Properties.

3. Then keep going down in the interface that comes out, find an Internet protocol, and double-click to open it.

4. Then all the interfaces that come out will be selected on the button that is automatically obtained, and click OK after setting.

5. Then call your browser, enter and enter your password. It's all admin.

6. After entering, enter the interface of the fast network and click the setup wizard on the left.

7. After clicking, in the interface that comes out, click Next directly.

8. Click Next. The default in the interface is to let the router choose the appropriate way to surf the Internet, and there is no need to change it directly to the next step.

9. Then there will be an account password to enter, which is your account and password that you will be told when you install broadband, enter it directly and click Next.

10. Then come out of the interface and choose what you need. Set the name and password of the router, and click Next after you have set it.

11. Then after clicking, an interface will come out for you to check the parameters you set, and click the save button after confirming that it is correct.

12. After saving, a setting status will come out, and you can check the current situation of your own settings, and at this point, the setting of wireless routing will be completed.