There is a lot about the installation of the router, how to install and use the router

Connect the computer network card with the LAN port of the router with a network cable and turn on the power of the router;

Enter the default username: admin and the default password: admin; Click OK.

Click Setup Wizard in the left rail, click Next;

Click on ADSL Virtual Dialing (PPPoE) and click Next;

Enter the broadband, password, and click Next;

Click Done. Many friends think that the dial-up connection is over after setting up, but in fact, there is still one point that is not completed. Because the following settings are not completed, many friends encounter 691 errors in dialing, or can connect to the network, but it will be dropped after a short time.

Let's continue with the setup:

Click the MAC address clone menu in the network parameters menu on the left sidebar, click Clone MAC address in the interface that appears, and click Save. At this point, the router will prompt you to restart the router, click OK to restart the router.

After the router restarts, close the Internet Explorer.

Connect the WAN port of the router with an incoming network cable, and then connect the computer to the LAN port of the router with a network cable to start surfing the Internet.

Note: "Some users have multiple computers at home, but don't know the MAC address of which computer to clone. You only need to directly connect the cat (or home network cable) to the computer with a network cable, and then dial on the computer, which computer can dial up the Internet, and clone the MAC address of which computer.

These processes are done and absolutely ready to use.

Enter it on the browser, and then a thing will pop up, and then enter, the password, it's admin, and then you enter the router password in it, and you're done.

If your computer is dial-up Internet access, install a router. Install the Internet cable, plug it into the computer and it's OK, you don't know this? I was in elementary school Moriuchi.

A broadband method of accessing more than two computers, buy a broadband router (several LAN ports can be on several computers, there are four, eight, etc.), according to the following data settings, you can achieve shared Internet access:

How to set up the Internet access on the broadband router (with tp-link as the column, basically the same):

1. Connections:

Connect the ethernet cable (RJ-45) from the Ethernet port of the modem to the WAN port of the router.

Connect any port of the LAN port of the router to the network card of the computer with a network cable;

2. Computer settings:

Set your computer to automatically get an IP address.

Look at the IP address obtained, which is generally the address of the segment or segment.

To view it, click Local Connect in the lower right corner of the taskbar.

There is an IP address in the support.

Or the Start Menu.

Run. - Enter cmd enter.

Enter the command ipconfig all;

3. Log in to the router:

Open the Internet Explorer browser.

Enter the gateway IP in the address bar, which is the IP address of the router, usually or - the username and password is admin

Enter the inside of the router;

Fourth, Internet settings:

Network parameters. -WAN port setting.

Select PPPoE dial-up based on broadband type – enter username and password.

Save it and you're ready to go online. Or follow the wizard to set it up.

5. Setting up wireless with wireless function:

Wireless parameters. - Basic settings.

The SSID is set by default or by yourself.

Automatic band selection.

Mode: 54Mbps

Turn on the wireless function.

Allow SSID Broadcast -- Turn on security settings.

Type WEP shared key.

The password format is of your choice.

Password customization (10 hexadecimal digits or 5 ASCII characters are required to select a 64-bit key.) To select a 128-bit key, you need to enter 26 hexadecimal digits or 13 ASCII characters. To select a 152-bit key, you need to enter 32 hexadecimal digits or 16 ASCII characters).

Save settings; 6. DHCP settings:

DHCP server.

DHCP services.

Enable. - The range of address start and end can be set by yourself and the LAN port address in one segment.

The lease term can be set within the range.

Static address allocation.

Add to. - Enter the MAC address and IP address to select for effect.

Save it.

Please refer to the manual for proper connection, check whether the connection between the computer and the crystal head is normal, and whether the regulated power supply is normal. Check that the cable to the router is plugged into the LAN port, observe the status of the indicator light, and when it recognizes the IP address, it can access the Internet normally. The disadvantage of installing a router is that it will be slower, and the advantage is that you can have 2 to 4 computers online at the same time, which has both advantages and losses.

After the power is turned on, connect the wireless router to the computer, open the browser and enter in the address bar: to enter the settings interface of the wireless router. According to the setup wizard step by step, select the Internet access method, and restart the wireless router after the setup is completed.

Next, go to the wireless settings and set the SSID name

The installation and setup of the router is as follows:

1.First connect the line, you can refer to the figure below.

2.After the line is connected, open a browser, enter the management address and management password of the router, and then enter the router background (the login address and login password of the specific router can refer to the manual or the label on the back of the router).

3.Once you've logged in to your back-office, select Quick Settings, then click Next.

4.Choose the way to access the Internet, usually ADSL users choose the first PPPoE, if you use other network service providers, then choose the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

5.Enter the password applied for from the network service provider, and go directly to the next step after entering.

6.Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

7.After entering it correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.