Small crafting materials are easy to find 5

Paper-cutting, fabric, origami are all okay or that kind of waste utilization, and it's good to put together all the little things that you don't have and see what you can do

Symmetrical paper-cutting is easy, just 2 pieces of colored paper of different colors.

The production method of handmade toys is as follows: The production method of duckling swimming toys is as follows: tools:

Cardboard, white paper, colored pencils, scissors, magnets, paper clips. To make this little toy, you need to prepare cardboard, white paper, colored pencils, scissors, magnets, and paper clips. 1.

Draw a cute duckling on white paper with a colored pen, don't draw too big, the width is wider than the paper clip. 2.Use colored pencils to draw a rectangle underneath the duckling, which is wider than the width of the paper clip.

3.Use scissors to cut the duckling and the Jane and rectangle underneath the duckling. 4.

Insert the paperclip into the rectangular piece of paper underneath the duckling, so that the paperclip is in the middle of the rectangle. 5.Fold the edge of the rectangle that connects the duckling back and fold it along with the paper clip to an angle perpendicular to the duckling.

6.Put the duckling on the cardboard and use the magnet to suck the paperclip under the cardboard, so that the hand holds the magnet under the cardboard, and the cardboard covers the duckling on top and swims up, and the duck swimming toy made by yourself is ready. The production method of the balloon car slag cover is as follows:

Materials and tools: cardboard, straws, balloons, hot melt glue guns, bottle caps, small sticks, tape, scissors, pen knives. 1.

Make a car shape out of cardboard. 2.Then he used a pen knife to dig two holes in the cap, inserted two straws, and fixed them with hot melt adhesive.

3.Place the cap on the top hole in the car. 4.

Make car wheels out of straws, sticks, and bottle caps. 5.Wrap the balloon over the cap and secure it with tape.

6.This way the moving car is complete.

Material: Ribbon roll [1 cm wide.

Scissors. Production process:

Cut out 4 ribbons [30 cm long] and press 11:19

Fold. Material: Ribbon roll [1 cm wide.

Process:1Cut off 4 ribbons [1 cm long].

The four ribbons folded in half are threaded into [long at the bottom] and finally tightened after wearing, like"+"Shape.

will"+"The 4 long sides of the shape are folded in half [long original upward, folded in half and downward] and tightened.

Fold 1 triangle out of 1 long country, and then fold 1 triangle upward.

Using the above method, fold the remaining 3 ribbons to carry out 2 triangles, check it into the edge close to the 2nd triangle, and tighten it, so that the two triangles stand upright in the "+" shape, and connect the remaining 3 ribbons in turn.

Thread the 4 long ribbons you just inserted into 1 square and thread the remaining 3 ribbons in the same way. The shape is like a " shape, and 18 such triangles can be folded.

First take two "" shapes, connect the two ribbons on both sides together, and then take 6 "" shapes in turn to form a ring, and then press down the middle part of the two "" shapes in the upper part of the ring, and press down the symmetrical part below, which can probably form a "peach heart" shape.

Take 2 pcs"Peach heart", and then the symmetrical position of its upper part is connected, and it is connected in the other part.

Take 1 more " ", connect it at the center, and will"Peach heart

Flip it over, and in the same way, place 3 pcs

Join, take another 2 volt "" shape, 16 sides are connected, probably can form a spherical shape, do 2 can be.

Then use a thin line to string the round ball and the "peach heart" shape, ** in the middle can be strung with some pentagonal shapes made of colored ribbons, zongzi, etc., (if there are conditions, you can hang a few small wind chimes on it to sell, the effect is very good).

This wind chime does not cost too much money and time, you may wish to make it yourself and give it to your friends and classmates, I believe they will like it again.

Hot melt glue gun (alternative: melt the glue stick and apply it to it. Uses: Paste-cloth. paper etc.) colored crepe paper (can be replaced: paper rattan. Uses: Make some fake plants, generally paper will not look so good)

QQ line (can be replaced: ordinary line, can not use wool wire.) Uses: Can be sewn when making clothes, etc.) Ribbon (can be replaced: a cloth cut strip that feels similar to the touch of the ribbon.) Uses: Make bows. ribbons, roses, etc

Needles (there is no replaceable.) Uses: sewn together with thread).

Cloth (there is no substitute.) Uses: Make clothes. hair accessories, etc.).

That's all I know, according to demand, it's all available on **.

If you want to make hair accessories, you need ribbons, QQ lines, alcohol glue, hair clips, (glue guns).

Salt water battery:

Materials: Wire (2 pieces), copper sheet, iron sheet, water, table salt, napkin, cup (the bigger the copper sheet, the better).

Method; 1. Connect the copper sheet and the iron sheet with wires and put them in the cup.

Add salt to the cup 2 (the more the better until the salt does not dissolve) and water to the cup 3.

In this way, the wire connected to the copper sheet is the positive electrode, and the iron spring mountain sheet is the negative level.

The voltage is not enough for you to connect a few of these devices.

The current is not enough for you to connect several such devices in parallel.

...You all are.

A school's ... Junior high school...

Do you have your winter vacation homework...

Nerve-wracking helped you.

Homemade nightlight.

Changed with an electric mosquito coil.

Transparent bottle with a little paint inside.

Dismantle the lamp beads inside the broken LED bulb.

Plus the board inside the charging head.

The two lamp beads are connected in series, fixed with hot melt adhesive, the heat is very small, and the heat can not be felt for 3 hours to have a night vision effect.

...You're all from the same school ... Junior high school...

Do you have your winter vacation homework...

Nerve-wracking helped you.

Homemade nightlight.

Changed with an electric mosquito coil.

Transparent bottle with a little paint inside.

Dismantle the lamp beads inside the broken LED bulb.

Plus the board inside the charging head.

The two lamp beads are connected in series and fixed with hot melt adhesive, and the heat is very small, and the heat cannot be felt for 3 hours.

Let's have a night vision effect.