2 computers public 2M network with router connection how to network so card

First, check whether the bandwidth is normal.

Second, check if the computer is poisoned (ARP virus, etc.).

Third, whether the DNS of the route is set normally (the DNS of Netcom that was originally set must now be modified to be normal for Telecom).

Can be connected to the Internet, that is the network connection limit, that is, there is a network, is your router is not set up, the new network cable must be plugged into the WLAN port of the new router, and then connect the new router through the computer with a network cable to enter the settings, and then it's OK, said so much, I hope to adopt, I can't continue to ask.

Note that when the new router is used by you as a switch, the LAN port cable from the original router should not be connected to the WAN port of the new router, but should be directly plugged into the LAN, so that the router is a switch, and a miracle happened.

If you want to connect the cable to the WAN port of the new router, go to the new router and change the WAN setting in the network settings to dynamic.

1.Physical Connection: The LAN port of the primary router is connected to the LAN port of the secondary router.

2.Set the IP address of the secondary route to not be the same as the IP address of the primary route

3.The secondary route DHCP service is down.

The mesh box you're talking about should be a cat. You connect the cat to the computer with the network cable to the WAN port of the router, and then connect your computer to the LAN port of the router, enter the router and dial according to the prompts.

Analysis:1It has nothing to do with broadband, because two computers share a router, but one has nothing to do and the other has intermittent Internet access.

2.Your computer system has been reinstalled, which means that it has little to do with the system.

Troubleshooting Resolution:1Look at whether there is a problem with the production of the network cable, take a good network cable to try it, whether the network cable and the network card are not well connected, this may be the main reason for the problem, you try it first, the network is this thing to try.

Ping the router, if the packet will be lost, check the interface between the network card and the network cable.

Long press the router point RESET for 5 seconds, and set it again, this time don't set the MAC address filter.

Other than that. Both computers should be set to automatically obtain an IP address and select IPv4

Let's see if there's something wrong with your computer's network card!! Try a different network card, and then there is your router factory reset to see!!

Is your disconnection a local disconnection?

Network card, network cable Router interface Swap the network cables of the two computers If the connection does not drop, replace the network card.

1. In the WAN settings of the router, the IP acquisition is fixed IP or automatic acquisition, and PPPoE is dial-up, so don't use it.

2. Be sure to distinguish the network segments. When you can surf the Internet without going through the router, press "Windows key + R" or select "Run" in the start menu and type "cmd" enter, and type ipconfig after the white box on a black background appears. Make a note of the IP address, subnet mask, and gateway.

3. If the cell network uses a fixed IP, it is wordy, and you should enter the IP address, subnet mask and gateway of your computer in the WAN settings. If it is obtained automatically, it will be troublesome, and you can not enter the above information separately.

4. After setting up the WAN, be sure to separate the internal network from him. For example, the IP address obtained in Step 2 is: The subnet mask indicates that the network segment of the cell is; In this way, you set the intranet network to any value).

0 and then the subnet mask can distinguish the network of the cell.

It seems that you can use the switch directly, and you can use it by plugging it in.

If you are sure that the other computer is working fine (no poison and no Trojans), please upgrade the configuration of that computer, thank you.

Do bandwidth throttling.

The downlink setting of the two units to the same bandwidth is 128k

The router restricts access to the client! Generally, 4 clients (including computers and mobile phones) are allowed to access router devices

The router at my home is also hey, I don't know if the router is too bad or. Again, I ask if anyone knows how to solve the problem of total disconnection...