Can I continue to use the electric pot after the water is boiled dry? On what basis?

The water in the electric cooker is boiled dry, it should still be usable, you have seen him is the automatic power off of the intelligent system, the water is boiled, to ensure a certain temperature, he must turn off the power,In the case of automatic safety protection, after tripping, add water to boil, or can be used, if the product quality of the electric cooker is not up to par, it is very likely to burn the wires or other spare parts, then it is necessary to repair the current electric pot generally has a shutdown program to maintain machinery and equipment, but can not boil the water dry, because the electric cooker, in order to better ensure the best heat transfer expectation, the bottom is generally very thin, if the water is boiled dry, it is easy to deform the bottom, in addition to high temperature weather.

Failure to transfer will also damage the electronic parts in the electric cooker, so it must not be allowed to dry out.

After the electric hot pot is air-boiled, it is more likely to have a variety of common problems when it is a good story for a long time. It is more common for everyone's temperature control board to cause problems. = For bimetal temperature-controlled electric pots, in addition to the slightly lower temperature regulation or poor contact of the electric heating tube, the failure of the temperature control board is more extensive, and it should generally be disassembled.

In this case, a thyristor.

Temperature-controlled, reviewed for low-voltage capacitors C cable sheath reduction, resulting in slow battery charging and thus not reliably opening and closing, slower heating up. After disassembly, the temperature will be normal.

This problem can also be caused by poor contact with the resistor RP. The temperature controller of the rice cooker is a magnetic watt, and its temperature turning point is 103 to 105 degrees. Therefore, it is not easy to jump before boiling water in a rice cooker, because the boiling point of water is 100 degrees.

After the water is boiled, the temperature sensor of the rice cooker or other electronic components will be used due to the high temperature during air boiling.

Damaged. <>

If it is not damaged, it does not necessarily mean that there is no problem, and it is very likely that the electronic components have become old, and the application time will be harmed. The electric pot is in a situation where no one takes care of it for a long time, and the water in the pot is boiled dry, and the long-term empty burning is very likely to lead to the failure of the stable control machinery and equipment, and the overtemperature will cause safety accidents. When overflowing or washing the pot, the stored water enters a part of the electrical products at the bottom of the electric cooker, resulting in the destruction of the internal structure of the electronic components, and also leads to the generation of electricity in the electric cooker.

I can't use it anymore. Because the water is boiled dry, the electric pot will not work.

Of course, you can, the quality of the pot is very good, you just need to wash it, and then you can use it normally. And the current electric pot will have the function of automatic power off.

I think it can't be based on the fact that if the water is boiled dry, if you use it again at this time, if it causes the electric hot pot to be **. It can even emit toxic substances.

1. If the circuit of the electric pot or the electric pot itself is not damaged after the electric pot is dried, then it can be used continuously, if the electric pot is damaged due to long-term dry burning and the internal parts are damaged or the circuit board is short-circuited, then it is not recommended to use it again, there is a risk of electric shock.

2. The electric pot is generally overheated automatic protection device, and the electric pot will automatically turn off when the electric pot is heated to a certain temperature, which belongs to the self-protection of the electric pot. The anti-drying device inside the electric pot can prevent damage to the electric pot after long-term heating.

3. Do not add cold water immediately after the electric pot is boiled dry, it is easy to cause the pot body to burst, you can unplug the power supply, and then add appropriate hot water after the electric pot cools down to clean the pot. Before using the electric cooker, you need to make sure that you add enough water to avoid dry burning the pot.

1. Take the pot away first, don't add water directly, especially cold water. The temperature of the boiled pot is very high, and it is easy to be scalded by the splashed water when adding water, so just wait for it to be cold.

2. If the boiling time is too long and the water is almost completely boiled, the temperature of the bottom of the pot will be extremely high, and the bottom of the pot will be seriously damaged in the long run. Usually do not add water immediately when the water is boiled dry, especially cold water, because the high temperature at the bottom of the pot will react quickly to the new cold water and may cause it to burst.

I can continue to use it. This type of pot generally has overheating protection, that is, the water will automatically disconnect the power supply after it is boiled dry. In the future, do not add cold water directly to the boiled pot, unplug the power and wait for the pot to cool down naturally.

As for the surface part of the pot being burned black, this has no impact on safety, it is just that the coating may not stick to the coating or it will not look good. However, it is also necessary to check whether there are any other places that have been damaged or deformed by the high temperature in addition to the surface of the pot being burned black. If not, it should be fine.

It's overheating protection powered off, you can continue to use it, no problem.

1. If it is a non-stick pan, you can boil the pot red, then pour boiling water, boil, and cook for about 10 minutes to dry before use.

2. The newly bought iron pot, there is a lot of rust that can not be used, you can use sandpaper to grind off the rust first, brush it twice with water, burn it on the fire to dry, and then brush it with hot water, you can use it.

3. You can also soak the iron pot in rice washing water for a few hours, and then wash it with water, and the rust on the iron pot will be cleared relatively cleanly.

4. Before using the new pot, you can pour an appropriate amount of vinegar into the heated iron pot, scrub it with a hard brush while burning, and wash it with water after pouring off the dirty vinegar to remove the peculiar smell of the new pot.

What to do after the electric pot is dry, 1, soak it in hot water, it is easy to wash it, do not use a steel wool ball brush, it will damage the pot, if it is an aluminum pot brush, then use a stool to cook rice after the aluminum pot is brushed, it is very bad for the body. (If you must brush, you can use a coarse cloth instead of steel wool) 2. If the bottom of the pot is pasted for rice and stir-frying, you can put a few mountain red in the pot, add a little cold water to boil (do not boil dry), and the bottom of the pot will be removed soon. 3. Tomatoes to paste the bottom of the pot A few tomatoes that are not very good are cooked in the pot, and they will naturally fall.

4. Beer and liquor to paste the bottom of the pot If you accidentally paste the pot when cooking, there is a pot at the bottom of the pot, if it is not easy to brush off, you can pour a little liquor and beer and a small amount of water (the ratio is 1:1: mix, it is easy to scrub clean after the lid is placed for 5 minutes.

5. Peel the apple or pear peel to paste the bottom of the pot Add some water to the apple peel or pear peel, and then it will be easy to clean. 6. Remove the oranges from the bottom of the pot Cut a few slices of oranges and boil them in the pot, let them simmer overnight, and the next day the paste will turn over, and it will be easy to remove. I hope my answer is helpful to you, and finally I wish you good health and a happy mood again!

1. What will happen if the electric hot pot is dry-burned.

After the electric hot pot is dry, it is prone to various failures after a long time. The most common is a problem with our thermostats. = For bimetallic thermostat electric frying pan, in addition to low temperature regulation or poor contact with the heating wire, the failure of the thermostat is more common, and it should generally be replaced.

In this case, the thyristor temperature control type is found to be that the insulation of the capacitor C decreases, resulting in slow charging and VS cannot reliably trigger the conduction, and the heating is very slow. Heating is normal after replacing c. If the potentiometer RP is not in good contact, this fault will also occur.

Second, how to use electric hot pot well.

In addition to avoiding dry burning in our use, we also need to think about other aspects. The power of the electric hot pot is generally large, and the sockets and power cords used should match the power consumed to avoid accidents. The electric hot pot uses a single three-core textile flexible wire as the power lead, and when connecting, the plug at one end of the power lead with a jack should be inserted into the electric heating socket of the pot body, and then the switch of the thermostat device should be placed in the middle or appropriate position.

Usually put it on the high temperature at the beginning, and after the water is boiled, it can be placed in the heat preservation mode. Be careful to have a good grounding.

3. Maintenance of electric hot pot.

No matter how good the electric hot pot is, it also needs us to maintain, non-constant temperature electric hot pot, do not dry burn the electric heating elements and pot body. When you need to remove the water from the pot, you should first turn off the power and cool it down slightly before releasing the soup in the pot, so as to prevent the residual heat of the porcelain plate at the bottom of the pot from burning the bottom of the pot. To keep the electric hot pot clean and hygienic often, after each use, the electric hot pot should be cleaned after cutting off the power supply, pay attention not to let water penetrate into the pot body when cleaning, and wipe the electric socket and other places with grease and sundries with a dry cloth.

=.= Anti-dry boiling is that there is a temperature switch inside When the water is boiled dry, the temperature will rise in a straight line. When it reaches a certain temperature, it will touch the switch, and then the electric pot will be powered off, so the electric hot pot with the function of preventing dry burning cannot be heated without adding water, you are only a pig.

It is a temperature switch protection to prevent fire caused by excessive temperature.

No! Dry burning is dangerous.

If the electric cooker is burned dry, it will cause serious damage to the electric cooker and may lead to safety issues, so it is generally not recommended to continue using the boiled electric cooker. Here are some of the things that can happen:

1.Burning: When the food or water has completely evaporated and dried out, there will be visible scorch marks on the bottom of the pan, which may even lead to burning.

2.Burned-out heating element: In the case of burn-out, the heating element of an electric cooker, such as a heating plate or heating rod, may exceed its designed operating temperature range, resulting in damage or burnout of the heating element.

3.Damage to other parts: The inner pot and other parts may also be damaged when it is dried, such as deformation of the inner pot or cracking of the glass lid.

If your electric cooker is burned dry, it is recommended to stop using it immediately and clean the inside and outside thoroughly after cooling the electric cooker. If any damage or abnormality is found, a professional repairer should be consulted for inspection and repair.

In order to avoid the electric cooker from drying out, you need to always pay attention to the cooking process, make sure that you add enough liquid or ingredients, and control the heating time and temperature reasonably.

Summary. Kiss If the water in the electric pot is boiled dry, it will not burn other electrical <><

Will the electric pot burn other electrical appliances when the water is boiled dry?

Kiss If the water in the electric pot is boiled dry, it will not burn other electrical <><

<>When the water of the rice cooker is boiled dry, due to the high temperature, Yan Min will burn out the thermistor of the electric rice cooker and other electronic components.

What to pay attention to when using a rice cooker 1, pay attention to cleaning the rice cooker inside the rice cooker and other food are to be served out, but also need to clean it in time, if you don't want to stay in the rice transporter rice or food May Day will be attached to the inner pot, it will become hard after a long time, at this time it is more difficult to clean, when cleaning, you can not use a brush or steel wool ball to scratch the inner pot, it will damage the coating on the scratch, and the cleaning of the inner pot must be dried before it can be put back into the rice cooker, At the same time, the surface moisture should also be paid attention to, and it should be wiped off. 2. Avoid entering the shell of the rice cooker If there is water, it is also necessary to wipe it clean in time to prevent it from seeping into the inside, and water can not appear on the electric heating plate.

3. Pay attention to the ingredients when cooking the ingredients in the rice cooker, in order to prevent the addition of more salty and sour cherry blossoms from ruining the state products, because the aluminum inner Yusong pot will also be eroded because it is too sour and salty, and it is easy to be damaged in the subsequent use.