What is the reason why the kettle is not heated when the kettle is energized

Since many people use the health pot for the first time, they are not very clear about its specific use method, so what is the matter with the health pot light fully lit but not heated? PChouse will take you to find out. 1. The indicator light of the health pot is on, indicating that the power supply line is normal.

The reason for not heating may be that the heating plate is burned out, the wiring is damaged, or the heating element is disconnected. 2. Look at whether the switch of the health pot has heating adjustment, if there is no heating adjustment, this situation is that the switch is broken. When the switch is broken, the indicator light is still on, because the indicator light is on only to know that there is a power supply that does not drive the heating pipe and the switch needs to be turned on the heating pipe, so you can't see the obvious reason for not heating.

It is recommended to send it to the maintenance office for repair, if it has been used for a long time, it is recommended to replace it with a new one, which is more cost-effective.

Reasons why the kettle does not heat up when it is energized:

1. Most of them are the problem of temperature control, because temperature control is the heart of the entire electric kettle, and its main function has been to control the water to turn on the water to automatically disconnect from the power supply, or turn on the power supply, and accept the corrosion of steam for a long time, resulting in the deformation and rust of the temperature control spring steel sheet so that the power failure or power on cannot be normal.

2. If the electric kettle is powered on, it heats up.

The dish is not heated, and this kind of failure should consider what material the electric kettle is. If it is a plastic kettle, it is generally enough to replace the heating plate directly; However, if it is a stainless steel kettle, it is estimated that the entire steel kettle body of the electric kettle will be scrapped, because the heating plate of the stainless steel body is welded and there is no way to replace it.

How to buy an electric kettle:

1. The electric kettle is an electrical appliance with water, and special attention should be paid to its electrical performance when purchasing to ensure that there is no leakage.

2. The interface between the heater and the body of the pot should be installed firmly, sealed well, and there should be no water leakage. When purchasing, you can use your hand to gently toggle the heater to check whether the assembly is firm and should not be loose.

3. The connection between the power lead connector and the body of the pot should be reliable, the tightness should be appropriate, and the assembly and disassembly should be flexible.

The solution to the kettle powering up and not boiling water is as follows:

1. If the power switch is normal, the fault mostly occurs in the insulation switch. First of all, see whether the reed of the bimetal sheet is pressed against the switch contact rod, if it is pressed too tightly, you can use tweezers to bend it upwards until the distance between the two. If the distance between the bimetal sheet and the switch lever is normal, the switch box should be disassembled, and the contacts and reeds of the insulation switch should be cleaned and repaired.

2. The indicator light is on, indicating that the power supply has been added to the indicator circuit, and the fault is in the electric heating pipe or its connecting part, and the common electric heating pipe is damaged and the contact is poor. Remove the electric heating pipe and measure its resistance value. If the electric heating pipe is damaged, it can only be replaced.

The poor contact is mainly due to the serious corrosion or deformation of the contact reed in the power plug assembly, which can be disassembled and repaired by the switch box, and it is best to replace it with a new one if the damage is serious.

3. The common reason is that the temperature sensor is seriously deformed or the action of the switch connecting rod is blocked. For the former, the convex angle of the small tongue of the thermostat can be rebent to make it push the switch connecting rod normally. For the latter, it is necessary to find the obstructed part or foreign body, which can generally be restored to normal by removing the foreign body and correcting the position.

Precautions for using a kettle.

1. The water injected into the kettle should not exceed the highest water line, nor too little, because overflow or empty boiling will easily cause kettle failure.

2. Fill the water into the pot, connect the power cord with the pot body first, and then plug the other end into the power socket to heat. For electric kettles with switches or automatic ones, unplug the switches to turn on the kettle.

3. The electric kettle is a high-power electrical appliance, read the manual carefully before use, and choose the appropriate power socket for digging fiber, and the socket needs to be used independently, and should not be used with other high-power electrical appliances.

4. The power plug should be kept dry and clean, never showered with water, and should not be placed close to the fire source, so as not to leak or burn out.

Possible reasons are:

1. The heating disc is damaged.

2. The thermostat or temperature fuse is damaged, resulting in the heating plate not being energized. The thermostat or insurance must be replaced directly.

3. The possibility of leakage is wide, it may be a line, it may be an electrical appliance, and the power consumption during this period will be small, and the voltage of the power grid will increase, and some bad lines or electrical appliances will leak due to the increase in voltage.

4. The internal circuit is damaged, resulting in the heating plate not being energized. It is also a direct replacement line.