How to set up a second wireless router from router to router

The principle of the edge connection of these two routers is in series, well, for the convenience of introduction, the router in the living room is called A, and the router in the bedroom is called B. Newly bought routers generally have the address.

It's both the user and the password.

It's admin

Router A doesn't need to be set, because it's in front of B, and all parameters are default, so I won't say how to dial. Just say B, connect B to the computer and network cable, enter it in the browser, this address is the default of B, enter admin to enter B's settings page. Select "Network Parameters" on the left - WAN port setting "- Ethernet access type" and select dynamic IP, so that you don't need to dial up.

Then select "Network Parameters" - LAN port setting "- IP address".

The address of B is displayed.

Here we're going to change this address to:

DHCP Service is enabled below. Nothing else. Click Save, and then the settings of the reboot are completed, and if you want to enter the router settings again, you will have to enter it in the browser.

It's set, you can put B in **, and talk about how A and B are connected in series. Use one network cable to connect one end to the outlet port of A (any port is fine), and the other end to the inlet port of B (that is, to the WAN). After the cable is connected, you can turn on the computer and surf the Internet.

Then set your wireless parameters and you're ready to go.

Wireless router to wireless router, the second router setup, there are two ways (provided that the first router has been set up and can surf the Internet normally):

The first method: dynamic IP mode (the first route is the primary route, and the second route is the slave route).

1. Plug in the router and do not connect the LAN port of the main router first, and reset the slave router (restore the factory);

2. Connect the computer from any LAN port of the router to enter the settings page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the LAN port of the main router to the WAN port from the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router first, and change the IP address of the slave router. For example, most router addresses are, we just need to change from router IP address to that;

2. Turn off the DHCP function from the router in the settings;

3. Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

As long as the login IP of the second route is changed to not be in the same network segment as the login IP of the main route, for example, the main route is, then the second route should be changed, if your two IPs are just different, then you don't need to set up, directly from the first route teleportation network cable to the WAN port of the second route, plug in the network cable to go online, the only thing to set is the wireless password, change the LAN port setting is to modify it in the LAN port setting of the route.

The connection and setup of the two routers are as follows:

1. First, look at a global map, and b is the second route.

2. Connect router B to the computer separately to set it, don't connect the WAN port of B first, and only use LAN to connect to the computer.

3. Open the management interface of router B in the browser and change the IP address of the LAN port of route B.

4. Turn off the DHCP function of route B.

5. The connection method of the AB router, after B is set, the WAN port of B is idle (or not).

6. If B is a wireless router, set it as usual, and finally the LAN port of B is successfully connected to the LAN port of A.

Note: 1. The IP addresses of the two routes cannot be the same.

2. DHCP cannot be turned on for the second route

3. The third and fourth steps cannot be reversed.

4. If you add a router, the setting method is the same as that of the second router.

As long as the login IP of the second route is changed to not be in the same network segment as the login IP of the main route, for example, the main route is, then the second route should be changed, if your two IPs are just different, then you don't need to set up, directly from the first route teleportation network cable to the WAN port of the second route, plug in the network cable to go online, the only thing to set is the wireless password, change the LAN port setting is to modify it in the LAN port setting of the route.

The 2nd router must be set up.

Wired cascades should be set as follows.

1: First determine whether the two routers set the same address, the same to modify one of them, generally the secondary assumption A is the primary router B is the secondary router, the address is not connected between the network cables.

Any LAN port on computer wiring B, log in to the B router.

In the browser address bar, type Enter.

Network settings--- LAN port settings*****=Modify to Save, and restart the router.

This should be remembered and used in the future landing b.

2: There are two ways to wiring, according to the selected wiring mode, debug any LAN port of A: A and connect the WAN port of B with a network cable Network --- WAN port setting--- select "dynamic IP" for connection mode", click Save System Tools --- Restart the router --- OK.

After success, any LAN port of B:A can be connected to any LAN port of B.

Network settings --- DHCP service --- turned off.

System Tools --- restart the router --- OK. Once you've succeeded, you're done.

1. A global map, b is the second route, we don't need to change any settings to achieve the first route, we only need to change the second route b

2. Connect router B to the computer separately to set it, don't connect the BWAN port first, and only use LAN to connect to the computer.

3. Open the management interface of the router in the browser, change the IP address of the LAN port of route B, and turn off the DHCP function of route B.

5. Connection method, after B is set, the WAN port of B is idle (it can also not be idle, but the setting is different from this, and I personally feel that this method is the best).

6. If B is a wireless router, set it as usual, and finally connect the LAN port of B to the LAN port of A Successfully Note:

1. The IP addresses of the two routes cannot be the same.

2. DHCP cannot be turned on for the second route

3. The third and fourth steps cannot be reversed.