Two routers are connected, how to set up the second wireless router

Two routers connected to the second router to set a wireless password method:

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser - enter the general router address is this or check the login information on the back of the router) into the route - enter the user name, password, (the default is generally admin).

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

The following describes how to set up a wireless router to connect a wireless router to another wireless router

1. How to set up the main router:

1. Plug the network cable (bus) into the WAN port of the wireless router, plug one end of the network cable into any LAN port of the wireless router and connect the computer network card at the other end, and turn on the power supply of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access and password.

5. Save and continue to set the wireless key, (it is recommended to use a combination of numbers and English for the password, and it is best to use the @ symbol in the middle, so as to prevent others from rubbing the net).

6. After saving, you can surf the Internet normally.

7. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

Second, the setting method of the secondary router:

1. Do not connect the secondary router to the main router first.

2. One end of the network cable is connected to any LAN port of the secondary router, and the other end is connected to the computer.

3. Change the LAN port IP of the login interface through the computer browser to avoid conflicts with the IP segment of the main router;

4. WAN port Internet access mode selection: dynamic IP connection, enable DHCP server.

5. Wireless settings and keys, save and exit.

6. Connect a network cable from any LAN port of the main router to the WAN port of the secondary wireless router, and the computer can access the Internet at this time.

Here's how to set up a second router:

1. First of all, you need to prepare 2 network cables, one network cable is connected to the LAN interface of the first router (i.e., 1 2 3 4), the other end of the network cable is connected to the WAN interface of the second router, and the other network cable is used to connect the LAN interface between the computer and the second router.

2. There is a management page address behind the router.

3. Then open the 360 browser, enter the management address of the second router, and enter the management page.

4. Next, enter the administrator password and log in.

5. After logging in successfully, click "Route Settings".

6. Then click "Wireless Settings".

7. After modifying, click "Save".

8. Then find the "Internet Settings" option of the second router and set up dynamic IP Internet access (automatically get IP address to go online).

You can just use the Internet mode or network mode, and choose the dynamic IP.

How to set up the second one for a router to a router.

You need to prepare two network cables, one end of which is connected to the LAN interface of the first router (i.e., 1, 2, 3, 4), and the other end of the network cable is connected to the WAN port of the second router.

Let's say that the router used to connect to the external network is the first router, and we use this router as the primary router. If your router is newly bought and more restored to factory defaults, then its IP should be.

2.Connect to the network with a network cable or wirelessly, it is recommended to use a wired connection;

Open a web browser, enter the router login address in the address bar, and press enter to confirm. Enter the username admin and password admin in the pop-up login box, as shown in the figure

4.First, set the router to connect to the Internet. Click "Network Parameters" on the left, and then select "WAN Port Settings".

5.Select "PPPoe" in the "WAN port connection type", enter the correct password, click "Save" at the bottom, and then click "Connect" after saving about 10 minutes, as shown in the figure above;

6.Second, the DHCP service needs to be enabled on the first router. On the left, select DHCP Server, and then select DHCP Service

There are usually two ways to connect a wired router to a wireless router, but the premise is that the computer with a line can access the Internet normally, then we only need to set the parameters of the wireless router and it's OK. The following takes TP-Link TL-WR340G as an example, and other wireless routers are similar.

First, any LAN port of the wired router or switch is connected to the wireless routing WAN port, in this method, the computer connected under the wireless router will be assigned IP by the DCHP of the wireless router.

1. LAN port setting.

Go to the wireless router and set the LAN port parameters, if we have a wired router IP is (ADSL cat occupancy.

Then the LAN port IP of the wireless router must not be set to the same network segment as the wired router.

2. WAN port setting.

If we select dynamic IP and DHCP is enabled on the wired router, usually the WAN port can automatically obtain the IP address from the DHCP of the wired router, so there is no need to set anything, as shown in Figure 1.

But if the wireless router can't be assigned a WAN address from the wired router, we need to do the following settings. (I've tried both static and dynamic, and I can surf the Internet normally).

Here we select the static IP and we want to set the necessary parameters. As shown in Figure 2 below, the IP set here should be consistent with the machine that can access the Internet normally from the wired router, which can be regarded as a computer connected to the wired router, of course, this IP can not be occupied by other computers with the wire.

The gateway of the WAN port should fill in the IP address of the wired router, otherwise it cannot access the Internet.

DNS It is recommended to fill in the DNS IP provided by the local ISP, I have tried to fill in the IP of the wired router, that is, although you can access the Internet, but occasionally the Internet speed will be affected.

Key points: The wireless routing WAN IP address must be on the same network segment as the LAN IP of the existing line. The gateway should be filled in with the LAN IP of the wired router

3. Turn on the DHCP service, and the wireless router will automatically assign the IP

The address pool network segment should be the same network segment as the wireless router, in this case the wireless router IP is , then we will set the address pool to.

3. Computer settings.

The computers connected to the wireless router are set to automatically obtain, if you want to manually assign IP to the computer for the convenience of management, you can also set it according to Figure 4, the settings at this time have nothing to do with the wired router, so the IP segment set should be the same IP segment as the wireless router, and the wireless router IP is We can fill in the gateway to fill in the IP of the wireless router, and finally.

Make sure that all the settings are successful and saved, then restart the wireless router to access the Internet wirelessly, of course, it is best to add a password to the wireless to prevent people from accessing the Internet.

The network management of the first router defaults to the second router can not be on the same network segment Connect the computer to the second router Enter the router's settings IP (for example, tp-link is Find the menu of network parameters Open the submenu There is a LAN port setting in it Go in and change the IP of the LAN port to point save Restart the router Hou You don't understand how to add me 349941324 I'm happy to solve the problem for you.

From your description, you want to use 2 wireless routers to network, the first one is the main router and the second is the extension router.

This should be done to allow networking.

1.Set the first router as the primary router, set dial-up, enable the DHCP service function, and connect the WLAN port to the external network line or the network cable from the ADSL modem.

2.The second router is set up as an extension router, which is the function of the wireless hub. Therefore, the DHCP function of the second router should be disabled, and the router address should be different from the first one, such as the first one, then the second one should be or something else.

Second, the cable coming out of the first router should be connected to the LAN port of the second router instead of the WLAN port.

Try the method above.

Don't change the settings of the first router (referred to as route A), and don't set the second router (referred to as route B) (restore it to factory settings).

Don't connect to Route A first, set Route B first: use a computer to connect to the No. 1 port of Route B, enter the default IP of the route in the computer browser: factory default) to enter the Route B settings, turn off the DHCP service, and then, open the LAN port setting of network parameters, change the IP address of the LAN port, for example, as long as it does not conflict with other IP addresses that have been used.

After the setting is complete, save and restart, and then the IP address that enters the B route will become. Then the 1234 port of route A (choose one) is connected to the 1234 of route B (any one), and then the 1234 of route B (any one) is used to connect to the computer! I'm tired to death ...

It is recommended that you follow these steps:

1。Disconnect the router from the telecom cats first, 2. Unplug the end of the computer that was originally connected to the cat and plug it into the LAN port of the router (the light with a number will turn on).

3。The wireless router ensures that the factory settings are protected from the effects of previous settings. Log in to the router, 19216811 or 19216801, enter it correctly in IE and log in to the router according to the manual.

4。Go to the router settings page to skip the wizard and go directly to the LAN port settings, change the LAN port address of the router to save and restart the router. Note that you can use it when you log in to the router in the future, instead of using 19216811

5。After restarting, connect the network cable out of the cat to the WAN port of the router, use it into the router settings page, and then skip the wizard directly to the WAN port settings, select dynamic IP for the connection type, save it and see if the WAN port obtains the IP address after saving the router running status (generally wait for 5 minutes), and then try whether the computer can open the web page, if the connection is normal, then enter the router to set up the wireless part of the function, and the rest can be operated according to the manual.

6.Turn on DHCP, note that its network segment should be the last to remember to save every step and finally restart the router in the router settings.

Plug a wired broadband network cable into the wireless router WAN port, and then use a network cable to connect directly to your laptop (or desktop) from the LAN port. Then open the browser, enter generally, or, (see your manual) enter the management and password, generally admin, enter the setup wizard, fill in step by step, according to your broadband** to make a choice, if it is adsl, you need to fill in the username and password, if it is a fixed IP address or not a fixed IP address of broadband, you have to fill in the necessary information, fill in all the way, very simple. For the security of data and wireless network, you go to the special wireless column to start the key, generally choose the wep method, fill in the key you want to set, pay attention to the number of key bits, see your page prompt, and then select the route in the route to restart, not manual power off, and then it's OK, search for the routing signal, enter your preset password everything OK!

It's very simple, the second router access mode selects the IP mode, and then changes the network segment to not be in the same network segment as the superior route, for example, the first one is the second can be on it, and then the route broadcast is turned on after encryption.

The secondary routing is simple, enter the login IP after the pop-up window and then enter the password of the route, there is a write at the bottom, and then there is a setup wizard on the left after entering, and then select the dynamic IP, and then fill in the wifi password you want, and then save and restart it.

Just change the address of the second router.

Just modify the IP address of the second router so that it doesn't conflict with the first.

Just set it up like you would your first router.

Plug in the LAN port of the second router and don't have to do anything.

Are you talking about wireless bridging?

Two routers: one is a router and one is a wireless router, assuming the wireless router is the primary router.

To connect two routers, you need to set them up separately.

The main router is set up as follows:

1. One end of the network cable is connected to the LAN port of the router, and the other end is connected to the network port of the computer.

2. Open the browser and enter it on the router box or in the manual).

Enter your router username and password.

3. Point setting wizard.

Internet access: PPPoE

Internet ID and Internet Password: Enter the broadband account and password.

Click Next.

4. Wireless status: on.

SSID: Enter the name of the wireless device.

Channel: Select 9 (if connected to an Apple mobile device or Mac: select 11 or 13).

PSK Password: Enter the wireless password.

Other defaults are sufficient.

5. After the setting is completed, one end of the network cable is connected to the LAN port of the modem, and the other end is connected to the WAN port of the wireless router.

The secondary router is set up as follows:

1. One end of the network cable is connected to the LAN port of the router, and the other end is connected to the network port of the computer.

2. Open the browser and enter it on the router box or in the manual).

Enter your router username and password.

3. Select [DHCP Service] under [DHCP Server] in the left sidebar, click [Disable], click [Save].

4. Select [Network Parameters] - LAN Port Settings] - enter in the [IP Address] item, and click [Save].

5. After the setting is completed, one end of the network cable is connected to the LAN port of the main router, and the other end is connected to the LAN port of the secondary router.

Note: The WAN port of the secondary router is idle.