How to measure the size of the ring, and the size of the ring is compared to the table of the circle

Paper strip fine line measurement method: wrap the paper strip around the base of the finger and mark the intersection with a marker; After marking, take a thin line of paper, measure the length of the mark with a ruler, and then compare it with the ring number table.

Inner diameter measurement: If you have been wearing a ring, remove the ring on your hand, measure the inner diameter of the ring with a ruler, and then compare it with the ring number table.

Ring Size Stick Measurement: Wear the rings one by one to find the one that is most comfortable to wear...

1. Paper strip (string) measurement method 1. Prepare materials.

A4 paper, pen, scale.

2. Measurement steps.

First of all, the A4 paper extension cut out a long strip of paper with a width of less than 1cm, and then wrap the paper strip around the fingers, remember to make a circle at the maximum finger joint, the elasticity is mainly based on the comfort level, mark the overlapping position with a pen, and finally spread the paper strip flat, and measure the distance between the two points with a scale ruler, that is, the finger circumference. If you use a thin rope, it is the same as a paper strip, but it should be noted that the rope should be as non-elastic as possible.

3. Precautions.

Because the flesh of the fingers is elastic, it is best to tighten the paper or string around it slightly to avoid being too loose.

If you want to use string, choose an inelastic one, such an error will be relatively small.

There will be a certain error in this measurement method, so it is recommended to measure several times and take the middle value of the scale to reduce the error.

2. Professional tool measurement method.

There is a ring size stick specially used to measure the size of the hand, this tool has a string of rings of different sizes, put a suitable ring on a certain finger that needs to be measured, and then remove the ring and put it on the ring stick, and check the value. This ring size stick is more common in jewelry stores.

3. Ring inner diameter measurement method.

If you have worn a ring before, you can draw the inner diameter of the previous ring on the paper, measure it with a scale and compare it with the size chart. It should be noted that the pen should be perpendicular to the paper, and try to choose a pen without edges and corners, otherwise it is easy to make errors.

These three measurement methods are suitable for buying rings online, but if possible, it is best to try them on in person.

Note: In the process of measuring the size of the ring, try to keep the temperature balanced, not too hot or too cold, because the finger will expand and contract due to the temperature, resulting in inaccurate measurement; If it's winter, it's recommended that the size be a little looser on the basis of comfort, and if it's summer, focus on comfort, or be a little tighter.

The size of the ring is divided into Hong Kong version, American version, mainland version, European version, etc., remember to check the size comparison table of the corresponding version after measurement.

Whether as a token of love or as a decoration, the ring plays a very important role. However, everyone's finger thickness is different, and the requirements for ring size are also different. To buy the right ring, you first need to be the right size.

For ordinary consumers, how to do the amount of rings better? The following is a very convenient way to measure the size of the shank.

How to measure the shank.

How to measure the shank.

Prepare a thin strip of paper, a pen, and a ruler, wrap the paper around the base of the finger and tighten it, mark the intersection of the paper strips, and then use it to measure the distance between the two marking points, and then you can get the finger circumference. By comparing the finger circumference with the "Ring Size Comparison Table", you can get the hand size of the finger, that is, how many size of the ring to wear. It is advisable to measure several times, whichever appears the most.

This is a very simple and achievable way for anyone to measure the shank, although it is also possible to measure with a non-elastic string instead of a paper strip. In addition, you can also go to a jewelry store to measure the ring number, for example, a man's DR diamond ring that can only be ordered in a lifetime supports size measurement.

Ring size comparison chart.

How many rings do you wear?

Different versions of rings are in different sizes, here is an example of a ring size comparison table for DR diamond rings. Usually women's rings are size 10-14, men's rings size is size 18-22, which can be compared to the following table:

Ring No. 8, circumference 46 mm; Ring No. 9, circumference 47 mm;

ring number 10, circumference 48 mm; Ring number 11, circumference mm;

ring number 12, circumference 51 mm; Ring No. 13, circumference 52 mm;

ring number 14, circumference 53 mm; ring number 15, circumference 54 mm;

ring number 16, circumference 55 mm; ring number 17, circumference 56 mm;

ring number 18, circumference 57 mm; ring number 19, circumference 58 mm;

ring number 20, circumference 59 mm; Ring number 21, circumference mm;

Ring No. 22, circumference 62 mm; ring number 23, circumference 63 mm;

ring number 24, circumference 64 mm; ring number 25, circumference 65 mm;

ring number 26, circumference 66 mm; ring number 27, circumference 67 mm;

DR Diamond Ring A man can only customize one in his lifetime.

For example, the diameter is r, the radius is r 2, and the circumference is r, you take a cotton thread around your finger and measure how many centimeters it is, according to the formula, that is, calculate the r, this is the diameter of the ring you need to buy, it will not be too bad.

The content of the ring size comparison table is as follows:

Most girls wear rings with rings numbered 10-15, with more rings from 12 to 13, and most boys wear rings with rings numbered 17-22, with more rings from 18 to 20.

The corresponding table of ring size and ring number varies from country to country. The smallest size of the European ring ring is No. 44, which corresponds to the number of 4 numbers in China, and the largest is No. 67, which corresponds to the number of 27 numbers in China. There are a total of 28 numbers in the ring size corresponding to the US size, the minimum is from size 3, the circumference is 44 mm, the ring diameter is mm, the maximum is 13, the corresponding ring circumference is 71 mm, and the diameter is mm.

Note Hypocrisy:

Rings are everyday jewelry, and it is inevitable that they will be exposed to more or less germs on a daily basis, but the edges, crevices, and inside of the ring are often hiding places for germs. If you touch cooked food with your ring hand, it will pollute things and be very unhygienic.

Many people are also afraid that the ring will slip between their fingers and be lost, so they will choose a smaller ring when choosing a ring. In fact, this practice is not suitable for ring wearing.

Before understanding the comparison table of ring ring numbers, we need to pay attention to the fact that there are many countries with different ring size and ring number corresponding tables, and the three versions that are more commonly used in the market are the American version, the Hong Kong version, and the mainland version.

For example, a ring with the same ring number in China and the United States is completely different in size, and the American version will be slightly larger. Most of our domestic use is Hong Kong code, China's children's ring size is generally 1-5, most of the women's ring size is 12-13, and the men's ring size is between 18-19.

If you really don't know how to measure your finger size, you can click on How to Measure and teach you how to measure in a relatively simple way. According to the circumference of the root of the finger, the ring number comparison table can quickly know the ring number corresponding to the finger. Although there is an international standard reference for ring size, due to the number of ring brands on the market, there will also be cases where the ring size is not standardized.

The methods have these:

1. Wear the ring directly: borrow someone else's ring or your own ring, find the most suitable ring for yourself, measure the diameter of the inner ring, or the circumference of the inner ring, and compare the ring size comparison table to confirm the hand size.

2. Use the ring measuring ring to measure: The ring measuring ring is a professional tool for measuring hand size, which can be determined by try-on experience.

3. Use cotton thread or paper strips, wrap your fingers, determine the length, and then compare the ring size table to determine.

The first two are the most scientific and accurate methods of measuring hand size, and there are often errors in the measurement with soft tools such as cotton thread.

There is also a need to wear rings.

This kind of attention is not recorded in writing, but is a convention. The people believe that the left is up, the right is down, the left symbolizes dignity and strength, and the right symbolizes gentleness and thoughtfulness. Therefore, people wear rings with "men on the left and women on the right".

In addition, men wear it on their index finger to indicate courtship, those worn on the middle finger indicate that they are in love, and those worn on the ring finger indicate that they are married.

Women generally do not wear it on their index fingers, while others are similar to men. If a person wears a man on his little finger on the left and a woman on the right, he or she is clearly celibate. In contemporary folklore, when men and women interact emotionally, they must pay attention to the position of the rings worn by each other, respect this conventional custom, and get along appropriately.

The methods of ring ring mouth measurement are: fine line measurement method, inner diameter measurement method.

1. Thin line measurement method: take a thin line with a wide width of 1 cm, the thin line is inelastic, which can avoid measurement error. Wrap the thin wire around the root of the finger, mark the intersection of the thin line with a marker, mark it after the mark is completed, measure the length of the mark with a ruler, and then check the ring number table against the ring number table to find the ring ring number corresponding to the circumference of the finger.

2. Inner diameter measurement method: If you have always had the habit of wearing rings and selling fingers, then you can take off the ring worn on your hand, measure the inner diameter of the ring with a ruler, and then compare the ring number table to find the number of rings that are suitable for good luck. Or take a piece of white paper, put the ring on the paper, use a pen to circle the inner ring of the ring, use a ruler to measure the circumference of the circle on the paper, and then compare the ring number table.

Precautions for measuring the ring rim:

Some rings are group-set with broken diamonds, and it is troublesome to change the circle in the later stage, or even cannot be changed at all, so the size of the ring must be accurately measured. For example, measure it several times and tease the average value quietly. Generally, there is a slight difference in the size of the left and right hands, and which finger you are ready to wear will be measured.

If you are elderly or have large finger joints, you can add 1mm or 2mm to the measurement.

The circle slogan is not necessarily an integer, it can have half a circle, for example, the circle mouth has5 and so on. If the belt is small with No. 10 and large with No. 11, then the ring mouth can be customized.

For some rings with wide arms, such as men's rings, or wide couple rings, the hoop is slightly larger than half a circle. If the tool is measured, it is half a circle larger than the circle mouth of the measurement.

The ring ring can be measured in several ways:

Fine-line measurement method: take a thin, inelastic line to avoid measurement errors. After wrapping the thin thread around the base of the finger for a week, mark the intersection with a marker, complete the marking line, measure the length with a ruler, and then check the ring number chart.

Inner diameter measurement method: If you have already taken the middle finger of the ring, you can use a ruler to directly measure the inner diameter of the ring, or put the ring on paper, use a pen to draw a circle around the inner circle, use a ruler to measure the length of the circle, and then check the ring number table to find the appropriate number.

Size stick measurement method: buy a special tool for measuring the size of the finger, called the ring size stick, which consists of a graduated size stick and a ring of different sizes, wear the rings one by one, and read out the number of engravings.

Direct measurement: If you purchase a "joint ring", you can directly measure the part of your finger that needs to be worn.

Measuring with String, Blank Paper, or Tape Measure: These methods are similar to fine line measurements, except that the tool is replaced with a rope, white paper, or tape measure. Wrap the string around your finger and make a mark, just measure the distance between the rope marks; Using white paper is also to put the ring on the paper, use a pen to draw a circle around the inner circle, and use a ruler to measure the circumference of the circle; Wrap the base of your finger with a tape measure and record the circumference of your finger as measured by the tape measure.

It should be noted that there may be differences in ring size standards in different countries and regions, usually based on the ring size standards of the Hong Kong version, and it is best to refer to the specific ring size comparison table to obtain the ring ring number after the results measured by the above methods.

The ring ring mouth measurement methods are: ring size stick, rope, ring inner diameter.

1. Ring size stick: You can use a ring size stick to measure the size of the ring, and the ring size stick is a tool specially used to measure the size of the hand. When wearing the right ring on your hand, remove the ring and put it on top of the ring size stick, and then check the value on the size stick.

2. Rope: To measure the size of the ring, you can wrap the string around the largest part of the finger joint, and then mark the part where the two lines cross. After removing the rope, use a ruler to measure the distance between the two markers, which is the size of the ring.

3. The inner diameter of the ring: If you have a ring of the right size, you can also put the ring flat on the white paper. After that, draw a circle along the inner ring of the ring with a pen, then use the diameter of the two inner rings of the ruler, and finally compare the ring size chart to get the size of the ring.

Ring Meaning:

Commitment: If you give a ring to the opposite sex, it is an act of confession that you want to be with you. If it is given to a lover, it is a hope to tie the other party, to express a kind of commitment, implying belonging and hope, and to want to grow old with the other party.

Marriage: Wearing a ring on the left index finger represents a desire for marriage. Wearing a ring on the middle finger of the left hand indicates that you are engaged. Wearing a ring on the ring finger of the left hand means that you are married. The little thumb of the left hand wears a ring, which means that Qi Chan is an unmarried family.

Friendship: Friends can also give each other rings, implying that the friendship between each other lasts forever. When the ring is given to the younger generation, it means hope and sustenance, the ring represents the family, and the ring is given to the younger generation to express the hope that the other party can always remain happy and successful.