What should I do if the gas valve of an electric pressure cooker falls off?

You can install it back, but it is not as big as the gas pressure cooker, but the electric pressure cooker will also bubble like the ordinary pressure cooker, if it will leak, you turn the valve to different angles may not leak, there is no trick at all. 1. The main function of the float valve is to float up and lock the push rod plate when there is pressure in the pressure state, and limit the role of opening and closing the cover. Therefore, the design of the float valve is not superfluous.

Second, the pressure limiting valve function of the pressure cooker, the pressure limiting valve as a safety protection, it is not fastened to the top. Because it must be active, when there is overpressure in the pot, it can push the pressure limiter to shift and vent the steam. 3. Note that the float valve floats up when the temperature in the pot is higher than 100 degrees and the pressure is higher than the atmospheric pressure.

You can also see it during the process of cooking rice or boiling water. In addition, during normal operation, the pressure limiter valve is not vented, because the pressure cooker pressure setting will not activate the pressure limiting valve unless there is a fault. The float valve is actually one of the multiple protection devices of the electric pressure cooker.

1. The aging of the sealing rubber ring causes air leakage due to incomplete sealing, and the sealing rubber ring needs to be replaced. 2. If the middle layer of the pressure cooker is lowered due to long-term use, you can use a gasket to raise the middle layer. 3. The heating plate of the pressure cooker is lowered and the heating plate is raised.

4. The lid is deformed and needs to be replaced.

There are several reasons why the pressure cooker safety valve does not fall back, first, there is still pressure in the pot, and second, the valve column is blocked by food debris around it, so that the valve column cannot fall freely without pressure.

The third, and most prone to failure, is that the cover cleat under the safety column is not adjusted to the correct position, and it takes a certain amount of experience to adjust the position of the cleatrix. The cleats are on the side of the lid of the pressure cooker, while the contact point is on the inside of the lid.

The electric high pressure cooker method can't go down, which means that there is still gas in it. The gas must be deflated before the valve can go down.

Summary. Hello dear, happy to answer your <>

If the air release valve on the electric pressure cooker falls out while in use, it is recommended that you take the following two methods:1Try reinstalling the bleed valve.

Usually the air release valve of the electric pressure cooker can be removed and installed, you can carefully read the manual or search for the relevant ** to learn the correct installation method when installing. 2.Contact your electric pressure cooker manufacturer or after-sales service center to purchase a new bleed valve or have them help you replace it.

Generally speaking, manufacturers or after-sales service centers will provide corresponding accessories or repair services<>

What should I do if the air release valve on the electric pressure cooker falls off when I am in use.

Hello, dear, I am glad to answer the <> of [fresh hail flowers] for you

If the air release valve on the electric pressure cooker falls out while in use, it is recommended that you take the following two methods:1Try reinstalling the bleed valve.

Usually the air release valve of the electric pressure cooker can be removed and installed in a car position, you can carefully read the manual or search for the relevant ** to learn the correct installation method when installing. 2.Contact your electric pressure cooker manufacturer or after-sales service center to purchase a new bleed valve or have them help you replace it.

Generally speaking, the manufacturer or after-sales service center will provide corresponding parts or repair <>services

Here are some <> related extensions that we hope you will find helpful

It should be noted that the electric pressure cooker is a kind of more complex Peichun kitchenware in the spine, and it must be operated in accordance with the operation steps on the manual to ensure safety. If you are not familiar with how to use it, it is recommended that you ask someone you know to help you use it first. <>

1. Long-term use causes food residue around the valve, so that the valve cannot be lifted freely. The solution is to clean the land file carefully, and if necessary, rinse it with a strong stream of water. 2. The air valve and the pot lid are not original, and the weight is too large, resulting in the temperature cannot be lifted smoothly.

You can go to a small appliance repair shop to change the valve with a small mass. 3. The pot body should be fully bent and heated to produce steam, and the air valve should be pressurized naturally in the morning. Maybe you are too anxious when using it, and you should wait until the gas in the pot reaches a certain amount, and the gas valve will naturally be up.

Dear users, hello! We're happy to answer for you! 1. The lid is not covered is definitely the most common reason, in general, it is the first time to use the electric pressure cooker or the electric pressure cooker is not familiar, resulting in the lid is not covered, when you turn on the electricity, there will be exhaust phenomenon, of course, it will not appear after boiling for a while, and it will not appear when the power is turned on at the beginning.

Solution: This is relatively simple, as long as the lid is covered, the normal electric non-slip pressure cooker is to put the lid on the inner tank, and then rotate clockwise when the finger on the lid is aimed at the corresponding place of the inner tank. 2. The sealing ring is a common cause of air leakage in the electric pressure cooker in many cases, such as the aging of the sealing ring, the sealing will become very poor, and it will be easy to leak air, and the sealing installation is not right, sometimes the sealing ring is taken down and cleaned, and then the installation is not right, and the macro ruler will leak air, and there are a lot of sundries on the sealing ring, which will cause the sealing ring function to be damaged, which will also lead to the leakage of the pressure cooker.

Solution: Whether the sealing ring is aging and broken, or there are foreign objects or the installation is wrong, it can be solved according to the specific situation, and the problem of the sealing ring is the most common cause of leakage and high gas. 3. The exhaust valve is in an exhaust state, and some owners may turn the exhaust valve to another side in order to quickly vent things after the pressure cooker is ready, so that they can quickly deflate the gas, which can discharge the steam in the pressure cooker earlier, and then take out the food inside.

However, some owners may forget to return the exhaust valve after using the pressure cooker, and they will not adjust it next time they use it, and the exhaust valve has been in the exhaust state, so the pressure cooker will definitely be exhausted after a while. Solution: Close the exhaust valve, don't vent, when you are using the pressure cooker, remember to close the exhaust valve, when you have finished the meal, and then open the exhaust valve when you need to vent.

The solution to the electric pressure cooker exhaust valve keeps leaking is to replace the exhaust valve.

If you check the exhaust valve closely, you don't find much of a problem. However, if there is still an air leak, it means that the exhaust valve needs to be replaced. As we all know, the exhaust valve is a very important part of the electric pressure cooker, once there is a problem with the exhaust valve, it will not only affect the tightness of the pot body, but also affect the stability of the pressure in the pot.

If the user wants to replace the exhaust valve, the user needs to remove the lid of the electric pressure cooker first, and after removing the exhaust valve, the user also needs to purchase the exhaust valve of the same specification for replacement. In the process of replacing the exhaust valve, the user needs to take special care to avoid damage or omission of other parts. When the electric pressure cooker is not used for a long time, the exhaust valve parts are more likely to rust, resulting in air leakage.

Precautions for choosing an electric pressure cooker

Generally speaking, if it is used to cook white tatami rice at home, it is recommended to use an electric pressure cooker with a capacity of 3L to 4L, which can cook rice for 3 to 4 people, which is enough for the family. If you often cook noodles, soup or a large amount of meat, it is recommended to choose an electric pressure cooker of more than 4L, which can meet the needs of more people or maintain the taste of food. If the family is smaller, choosing an electric pressure cooker up to 2L will be a good choice.

There are many brands of electric pressure cookers on the market now, and there are great differences in quality, quality and service. When choosing a brand, we should not only consider the popularity and credibility of the brand, but also see whether the brand has perfect after-sales service. Before buying an electric pressure cooker, you can learn about the evaluation, use experience and after-sales service of some brands.

1. Cause of failure: The valve gear is set incorrectly. If the gear is set on the exhaust gear, there will be a phenomenon that the pot will be exhausted all the time after it is boiled.

Solution: In this case, just change the gear setting back.

2. Cause of failure: The pressure cooker is not covered tightly. If the pressure cooker is not tightly covered, there will also be an electric pressure cooker leakage, which is not only a first-time user, even if it is a frequent user, but also because of a period of sloppiness, resulting in the pressure cooker is not tightly covered.

Solution: Re-cover the pressure cooker.

3. Cause of failure: There is a foreign body in the sealing ring of the pressure cooker. If there is a foreign object on the sealing ring of the pressure cooker, the pressure cooker is not well sealed, and there will also be air leakage.

Solution: Clean the foreign matter on the sealing ring.