Is it normal for the rice cooker to have a seam in the lid? How to stick the seams on the side of th

It depends on what kind of rice cooker you are talking about, if it is an old-fashioned rice cooker, it is normal for it to have a gap after closing the lid, because it needs a space to breathe, so that it will not cause excessive air pressure. However, if it is a new rice cooker, it is not very normal to have a seam, because the new rice cooker itself has an air outlet hole that can be vented.

The answer depends on what kind of rice cooker you're talking about? Because now it is the kind of smart rice cooker, there should be no gap, because it has its own exhaust hole, then the old-fashioned rice cooker is different, it is the lid and the body of the rice cooker are separate, this kind of case, then there is a little gap, and the problem should not be very big, that is, the steamed rice is steamed out and there must be no good taste without air leakage.

There is only a gap in the position of the lid of the pot, and the rice cooker can still be covered, so there will be no danger, but it is recommended to check other positions, especially the part connected to the socket, so as not to cause leakage due to other reasons. The consequence of the gap in the rice cooker may be that there will be overflow when the rice is cooking. It is recommended to contact the after-sales staff to test the rice cooker, and if necessary, take the method of repair.

The lid of the rice cooker is not tight, because the rubber band inside is not placed.

There is a gap where the lid of the rice cooker is not tightly covered, and that is because of the sealing ring on the lid of the rice cooker.

If it is not tight, it is recommended that you replace it with a new sealing ring, and the lid can be covered tightly, and there will be no gaps. The lid with the replacement seal is the same as new, it is particularly easy to use, and the cover is particularly tight, thank you for your question.

It is normal for the rice cooker to have a gap in the appearance of the lid, but generally there is a seal ring on the detachable lid after the lid is opened, and it is no problem to have this sealing and insulation. Of course, if you don't feel at ease, you can change the rice cooker.

It's normal to have a little gap.

In my house, you can clean the lid regularly, and sometimes the water and rice that comes up from cooking will get stuck in the gap between the lid. Words like this. It takes a lot longer to cook rice, and the cooked rice is not as delicious as when I first bought it, so keep the rice cooker clean at all times. Personal experience.

It is normal for the lid of the rice cooker to have a seam, and it does not matter if there is a slight gap when it is closed, and it does not affect the normal use.

Summary. How to stick the rice cooker button when it is turned onAnswer: The rice cooker is glued with double-sided tape or fish bead universal glue when the rice cooker button is turned on, and the rice cooker is cooked at the bottom of the aluminum pot by using a heating plate.

The heating plate has a built-in electricity**, which is controlled by an automatic switch. There is a round hole in the heating plate, and there is a warm and soft magnetism in the hole, which is pressed against the bottom of the pot by the spring. This is a pure ferrite.

How to stick the rice cooker button when it is turned onAnswer: The rice cooker button is turned on and the rice cooker is glued with double-sided tape or fish bead universal glue, which is a heating plate for cooking rice at the bottom of the aluminum pot. The heating plate has a built-in electricity**, which is controlled by an automatic switch.

There is a round hole in the heating plate, and there is a warm and soft magnetism in the hole, which is rotten and it is pressed against the bottom of the pot by the spring. This is a pure ferrite.

I'm still a little confused, can you be more detailed?

How to stick the rubber on the rice cooker button: 1. Use the kind of double-sided tape from the electronics factory, it is best to use a hot air blower to heat the panel when sticking, and let it cool and loosen it while it is under hot pressure, and the effect is very good. 2. You can choose to use AB glue for bonding, but you can't use the mold after bonding, and you can use it only after the bonding point is dry.