What should I do if the pressure valve of the high pressure rice cooker is gone?

High Voltage Rice Cooker No Pressure Reason:

The aging of the sealing rubber ring causes air leakage, and the pressure in the pot cannot be maintained;

2. Poor sealing of the rubber gasket of the exhaust nozzle causes air leakage, which indirectly leads to no pressure in the pot.

3. There is no pressure caused by air leakage of the float valve.

4. The pressure switch is damaged, and it is pressurized without normal heating.

Solutions to the above problems:

Replace the rubber sealing ring to ensure that it is well sealed;

Replace the sealant underneath the exhaust nozzle to make sure it is well sealed;

Replace the float valve so that it is well sealed;

Replace the pressure switch so that the pot can be pressurized normally and the pressure is maintained.

If it is caused by wear and tear of the exhaust pipe, you need to replace the exhaust pipe, and then tighten the screws of the exhaust pipe. If the electric pressure cooker has no pressure, if it is caused by the aging and leakage of the sealing ring, you need to replace the sealing ring again, and then close the pressure cooker lid. However, deformation of the lid and pot body will also lead to air leakage, and the lid and pot body need to be repaired or replaced; If the inner pot is deformed, the inner pot needs to be replaced.

If the pressure valve is gone, you can't pressurize, give the after-sales ** to explain the situation, listen to what the after-sales say, if you can't match it, you can only buy a new one.

You can go to this rice cooker manufacturer to buy a pressure valve at an after-sales service point near your home. Generally, the materials of after-sales maintenance points are all factory, as small as a small sealing ring and gong wire. You have to buy them all.

The pressure valve of the electric pressure cooker is gone, and this problem is not difficult to solve. It is recommended that you follow the model of the pressure cooker and go to the Internet to buy pressure valve accessories.

If you don't have a pressure valve, you can't use it, you can go to the place where you buy electricity and ask them to buy you a new pressure valve. Basically, so the pressure valves of electric pressure cookers are universal.

The pressure valve of the high-pressure rice cooker does not have it, and it is best to buy one and install it, because this is very important, it plays a role in the protection of excessive pressure.

The pressure valve of the high-pressure rice cooker is gone, so it is recommended to use one with the same model. Because it involves high-pressure issues, it is still prudent to find professional people to match. After all, high pressure is dangerous.

The pressure valve of the high-pressure rice cooker is gone, and you must change the pressure valve, otherwise it will not work.

If the pressure valve is gone, it can only be rematched. An electric pressure cooker does not have a pressure valve and will leak all the time.

Buy a replacement with the same model, report the rice cooker brand, and the model, and the store will know.

You can go to a repair shop for repairs.

Hello, for the sake of safety, let's go fix it, and if it can't be repaired, replace it with a new one.

Go to the repair shop and buy a new one.

Accessories are generally not retailed, unless you know the manufacturer, you really can't buy it as an ordinary pot.

You can buy it online, and there are all kinds of models and styles!

Safety valves may be clogged, focus on cleaning. In the cooking process, when the pressure in the pot reaches the working pressure, the pressure limiting valve exhausts through the exhaust hole to keep the pressure in the pot within a certain range to achieve the purpose of cooking. The function of the safety valve:

During the cooking process, the pressure in the pot is too high due to the blockage of the exhaust pipe of the pressure limiting valve, so the air is discharged through the safety valve to ensure the safety of the pressure cooker.

Precautions for cooking rice in a pressure cooker:1. The water level should not exceed three-quarters of the total height of the pressure cooker.

2. Determine whether the leather ring and the compressor valve are clean, and the compressor valve must not be blocked.

3. Turn down the heat after bubbling.

4. Pay attention to turn off the heat after cooking, otherwise the pressure cooker is easy to use.

The reason why the safety valve of the high-pressure rice cooker does not gas up:

1. The pressure limiting valve and valve seat are loose;

2. The sealing gasket of the pressure limiting valve, safety valve and safety plug is damaged;

3. The pressure spring of the safety valve loses its elasticity, and there is a gap between the valve pin and the valve body;

4. The safety plug fused piece is damaged;

5. The sealing ring in the pot is used for too long and loses its sealing effect.

It is enough to solve the problem according to the above situation.

The safety valve does not puff, which indicates 2 problems:

1. The pressure in the pot does not reach the pressure of the safety valve;

2. The safety valve of the pot fails;

If it is the first case, it means that the heat of your pot is not enough and the temperature is not high, you should check whether it is in a state of heat preservation or something, or check whether the heating wire is partially broken;

If it is the second case, it is very dangerous, you need to remove the safety valve to check whether there are rice grains blocking the pipe of the safety valve, and pay attention to cleaning up the residue in time.

If the safety valve is not inflated, there will be the following problems:

1. If the pressure in the pot does not reach the starting pressure of the safety valve, the heat of your pot may not be enough and the temperature is not high enough, you should check whether it is in a state of heat preservation, or check whether the heating wire at the bottom is partially broken;

2. The safety valve of the pot is ineffective, if it is the second case, it is very dangerous, you have to remove the safety valve to check whether there are rice grains blocking the pipeline of the safety valve, pay attention to clean up the residue in time.

Summary. What to do if the gas outlet valve can't be lifted when the electric pressure cooker cooks rice, hello, I'm glad to answer for you, there may be a variety of situations: 1. Long-term use, resulting in food residue around the air valve, so that the air valve can not be lifted freely.

The solution is to wash it carefully and rinse it with a strong stream of water if necessary. 2. The air valve and the pot lid are not original, and the weight is too large, resulting in the temperature cannot be lifted smoothly. You can go to a small appliance repair shop to change the valve with a small mass.

3. The pot should be fully heated to produce steam, and the air valve should be naturally pressurized inside. Maybe you are too anxious when using it, and you should wait until the gas in the pot reaches a certain amount, and the gas valve will naturally be up.

What to do if the gas outlet valve can't be lifted when the electric pressure cooker cooks rice, hello, I'm glad to answer for you, there may be a variety of situations: 1. Long-term use, resulting in food residues around the air valve, so that the air valve can not be lifted freely. The solution is to wash it carefully and rinse it with a strong stream of water if necessary.

2. The air valve and the lid are not original, and the weight is too large, resulting in the failure of the hall to jack up smoothly after reaching the temperature. You can go to a small appliance repair shop to change the valve with a small mass. 3. The pot should be fully heated to produce steam, and the air valve should be naturally pressurized inside.

Maybe you are too anxious when you use it, and you should wait until the gas in the pot reaches a certain amount, and the gas valve will naturally be up.

Precautions for using a pressure cooker1The inner pot should not be boiled empty or placed on other heat sources to boil in the early hall. 2.

Before putting the inner pot into the outer pot, wipe the inner pot and the heating plate clean, and rotate the inner pot left and right after putting it in, so as to keep the inner pot in full contact with the heating plate. 3.The sealing ring cannot be damaged, and it cannot be replaced by other rubber rings.

4.When the electric pressure cooker starts working, the pressure limiting valve must be dialed to the sealed position. 5.

The anti-blocking cover and sealing ring should be cleaned frequently, and the smile should be kept clean, and at the same time, in order to ensure that the sealing of the pot float valve does not fall, the lid cannot be forcibly opened. 7.No heavy objects should be added to the pressure limiter or replaced by other items.

8.If you are cooking porridge in the pot, you should not immediately remove the pressure limiting valve, otherwise the soup will spray out of the exhaust pipe. 9.

When turning the pressure limiter to deflate, do not put your hands and face close to the exhaust pipe of the pressure limiting valve to avoid being burned by the vented steam.

What should I do if the rice cooker pressure cooker has all the gas, but the safety valve does not fall and the lid cannot be opened.

<> dear, I've been waiting for a long time, the following is the answer to your question, I hope it can help you!

Dear, if the gas is exhausted and the safety valve does not fall, you can press the valve with chopsticks, it should be deflated when the top is up, and the card cannot be stopped, you can press it gently. The possible reasons why the rice cooker cannot be opened after the pressure cooker is deflated are: First, the pressure is not completely relieved, and you can wait patiently for the pressure to be completely depressed.

The second is that it has been a long time, although the pressure has dropped to normal atmospheric pressure, but the safety valve can not naturally drop to the position that can make the lid open normally due to the increase in resistance between the safety valve and the lid (oil, food residues and oxides), if this is the reason, you can poke the safety valve with the tip of chopsticks, but pay attention to clean up the debris between the safety valve and the lid in time after use, so as not to repeat the old trick next time. <>

Dear, if my answer is helpful to you, please give a thumbs up (comment in the lower left corner), look forward to your like, your efforts are very important to me, and your support is also the driving force for my progress. If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

The failure of the electric pressure cooker to fail to gas may be: 1. The pressure limiting valve, air inlet hole and exhaust hole have different rocks, resulting in blockage. 2. Rust or accumulation of oxides at the valve seat and valve pin.

3. The lid is deformed. 4. The sealing ring is deformed. 5. There are foreign bodies at the bottom of the inner tank or on the heating plate.

The electric pressure cooker is an upgraded product of the traditional pressure cooker and rice cooker, which combines the advantages of pressure cooker and rice cooker, saving time and electricity.

The operation mode of electric pressure cooker can be divided into two types: mechanical operation and microcomputer operation, of which mechanical operation is the traditional electric pressure cooker operation mode.

When using a pressure cooker for the first time, you must read the instructions for using the pressure cooker and do it according to the requirements of the manual.

Operating environment

Brand model: general

System version: General