How to make a flower watering artifact? How to make an automatic flower waterer

Nowadays, there are many people who raise flowers, but many people raise flowers but always die because they forget to water the flowers or are too late to take care of them on a business trip, which is a pity. Personally, I like to water flowers, and I have made some watering artifacts, so let's share them below.

One: First of all, the simplest is that this method is suitable for patients with advanced hand disabilities. Ingredients: A large thick bottle with a lid and an appropriate length of absorbent cloth strips.

Start by cutting a few holes in the upper part of the bottle with scissors, about one square centimeter or so. Then cut the strip of cloth so that it hangs down to the bottom of the bottle and has 40 cm long, bury one end in the pot and soak the other end in water, so that when the pot is dry, you can "water" the flower.

2: Sufficient tools for hot melt adhesive, hot melt glue gun, fine needle, suitable thickness of cylindrical object (about three fingers thick).

First, apply a layer of hot melt adhesive around the cylinder to make a shape, leaving the top and the bottom blocked. Then apply more reinforcement with hot melt adhesive, wait for the hot melt adhesive to dry and harden, and take it off the mold. Next, use a thin needle to make a small hole at the bottom of the thing you just made, the needle should be thin enough, otherwise the hole will be too large, which will cause the water in the artifact to leak too quickly, and you will not be able to water the flowers when you leave.

Bury the finished cylindrical object in a pot about three centimeters deep. Fill the cylinder with water and you can slowly "water" the flowers.

Three: It is almost the same as the second method, but it is to make a cylinder the size of a flower pot with dense fine holes at the bottom, put the flower pot into the finished cylinder, and then put it into the pot with water.

Although these methods are very convenient, after all, they are always adding water, and novices are not fine, which will always lead to overwatering and waterlogging the flowers. Therefore, it can only be used as a helpless act when the flowers cannot be watered temporarily.

Teach you how to make your own automatic flower watering artifact.

Automatic flower waterer production method: cut off the top of the plastic bottle of more than two liters, directly flip the top over, stuff two cotton threads, invert and embed the plastic bottle at the bottom, fill the container at the bottom with water, and introduce the dry water in the container into the soil by the cotton thread.

Herbaceous plants have shallow root systems and need more watering, while woody plants have a wide root system and do not need to be watered too frequently. Sandy soil has poor water retention and needs to be watered frequently, and clay soil has good water retention, so watering should not be too frequent. Plants with large leaves can be watered more, water-loving plants can be watered more, and drought-loving plants can be watered less.

You can water more when the hot water evaporates quickly, and you need to water more during the peak growth period of plants, and you need to control water when the plants are dormant.

Precautions for watering

Watering is to directly water the potting soil or flower beds to water thoroughly, mostly for fast-growing flowers or over-dry soil, generally do not drench plants and leaves, if the leaves are wet, plants may be sunburned. In summer, when the weather is hot, you can increase the frequency of watering, and pay attention to the best time to water in the morning or evening. Plant transpiration is strong at noon, watering at this time will affect plant growth, it is best to water at noon in winter, watering in the morning and evening will cause the plant root failure system to be frostbitten.

When watering plants in summer and winter, it is best to keep the water temperature consistent with room temperature, otherwise it will affect the root growth of the plant. When watering plants, it is best to use rainwater, river water, etc., tap water contains a large number of impurities that plants cannot absorb, and it needs to be precipitated for 2 to 3 days before it can be used.

1.I made a homemade flower waterer according to the one on the Internet.

Works well, a thread, water in a dripping way.

When I did it for the first time, I chose a green yarn, which floats on the surface of the water all the time and has a poor water absorption effect.

Tried for a long time without success.

If you change it to this, you will find someone out all of a sudden.

The choice of material is critical.

2.Preparing to make an inverted type, that is, there is a hole in the upper and lower parts of the bottle. ** Presented is a cloth strip plugged in the hole below, and it is also said that the size of the hole above determines the flow rate.

I used wool instead of strips of cloth, and the strange thing was that I hadn't punched holes in it yet, and the water was already dripping down the wool.

Through my own experiments, I found that the magnitude of the water flow velocity is related to the inclination of the bottle, and the vertical inverted flow rate is the fastest. The flow rate is also related to the thickness of the line, the thicker the line, the faster the flow rate.

That's why I made my own waterer.

Two threads, you can pour two pots at the same time.

If you want to pour more than one person at the same time, get a few threads.

Why don't you make a hole and you can get out of the water? I haven't figured it out yet, but it's so much fun!

Flower watering generally requires a watering tool, but for non-professional flower people, there is no need to buy a flower waterer, you can also make a good watering artifact by using mineral water bottles, mineral water bottles are really not difficult at all, and the following florist uncle teaches you DIY homemade waterers.

Look at! Homemade watering pure flower artifact is as simple as that:

Pictured: Materials and tools to be prepared outside the mineral water bottle.

1. After preparing the material tools, open two small holes near the bottom of the mineral water bottle, pay attention to the size of the hole as long as the straw can be inserted, not too big, it is best to arrange it up and down, and the opening position is not too far away from the bottom of the mineral water bottle.

2. Use clay or adhesive tape (AB glue is mixed 1:1) to block the gap between the straw and the small hole, fix them together, and do a good job of sealing, so as to avoid water from flowing out of the gap.

Pictured: Mineral water bottle waterer.

3. Bend the straw sticking out of the bottle downward, trim it into one long and one short, with a difference of 2-3 cm, and the straw below should be shorter than the straw above, so that the entire automatic watering device is completed.

4. After the above steps are completed, you only need to wait for the clay or glue to dry and fill it with water, and then close the bottle tightly to water your love flowers. How, isn't it simple? Ha ha!

Figure: How the flower watering artifact works.

Tips] The installation principle of the homemade waterer: when the water surface in the sink is lower than the height of the short straw, the air will enter the bottle from the short straw, squeeze out the same amount of water, and then flow into the sink from the long straw, so as to complete the "hydration" process of the plant.

Teach you how to make your own automatic flower watering artifact.

Prepare materials: AB glue (if not, you can replace it with other waterproof glue), large bottle (to ensure the amount of water), 2 straws, scotch tape.

Handmade DIY materials with a drink bottle auto flower waterer.

Step 2: Insert two straws and tape the long portion of the straw together.

Step 3: Trim the lower end of the straw into one long and one short, with a difference of 2 3 cm.

Step 4: Mix AB glue 1:1 and apply it to the pipette and the wall of the bottle to seal it.

Step 5: When the glue is dry, fill it with water, close the bottle tightly, and you can water your love flowers!

When the water surface in the sink is lower than the height of the short straw, the air will enter the bottle from the short straw, squeeze out the same amount of water, and then flow into the sink from the long straw, so as to complete the "hydration" process of the plant.

Find an empty pulsating bottle and a thin straw.

Make a small opening diagonally upwards in the bottle, about the same size as the diameter of the straw, and fix the straw on this small hole. Then prick the cap with a red-hot paper clip and make small holes, so that your flower waterer is ready.

A Coke bottle is drilled with a nail and then piped to the tap water.