What should I do if there is a watermark after washing the glass washing machine?

The watermark after the glass washer is washed is mainly due to the final rinsing problem, so changing the water for a few more rinses can reduce the appearance of watermarks.

First determine whether it is a watermark or a dirty;

1. Dirty. Look at whether the cleaning agent is suitable, or whether the cleaning agent has no cleaning power;

Take a look at the ultrasonic equipment (cleaning machine) working normally;

2. Watermark. See if the rinse water is clean and needs to be replaced; Rinse the number of times is enough; What kind of water is used, is it appropriate?

Take a look at the ultrasonic equipment (cleaning machine) working normally; Whether the oven is clean or not.

Hope it helps.

The reason why there is a water stain watermark on the glass after the glass washing machine is cleaned: the brush of the glass washing machine is already very dirty.

The sponge roller of the glass cleaning machine has been hardened.

The air knife of the glass washing machine is blowing at the wrong angle.

The wind in the glass washer heats up too high.

The glass already had mold marks before the Qing ruler was washed.

After edging, it was stored in a relatively high temperature environment for too long and not cleaned.

Of course, not all glass washing machines have sponge roller table and air heating, so check them one by one for your own cleaning machine.

If there are water stains on the glass washing machine, you need to wipe it on the glass with a damp rag to keep it moist enough, then apply laundry detergent to the glass water stains, then use a wet paper towel to wipe the water stain area, and finally use a dry rag to dry the glass, you can find that the water stains are gone. You can use old newspapers or wet towels to remove stains. If you have a stain on the glass that is difficult to clean, you can use beer or vinegar to wipe it off to dissolve the stain.

In addition, you can also use a special detergent to clean up stains, and the effect is also very good. Then in the process of cleaning, you need to use a toothbrush to scrub and brush off the stains stuck in the pattern, which can prevent the frosted glass from hiding dirt. At the same time, kerosene and gypsum powder can also be used to clean the glass, which can quickly disintegrate the stain and ensure that the glass is cleaner.

If the glass cleaning machine sticks to the oil stains, it is more troublesome, and it is necessary to use detergent to clean the glass in time to avoid the oil stains from solidifying, which will bring greater difficulties to the cleaning work. In addition, you can also put a protective film on the location of the oil stain, wait until 20 minutes, tear off the plastic wrap, and you can effectively clean up the oil stain.

Abstract: The glass that is processed and cleaned is offset, which means that the force at both ends of the pressure roller is not uniform enough. The solution is to adjust the balance of the roller in time.

There is a watermark on the reverse side of the glass washed out by the washing machine.

1.The angle of the air knife is not right2Air knife auxiliary heating is broken 3The aging of the sponge pressure roller (cementation) replenishes the water absorption, and it is checked from these three aspects.

It's not a watermark, maybe the imprint is brought by the **roller table.

Generally, the reason for this situation is that the chain is loose, or the bearing is damaged; Bearings can be replaced and chains can be tensioned.

Pure water or glass.

The glass that is processed and cleaned is offset, which means that the force at both ends of the pressure roller is not uniform enough; The solution is to adjust the balance of the roller in time.

Summary. 1. Towel wiping: the glass is blurred after wiping, which may be due to improper cleaning, at this time, the glass should be re-sprayed with cleaning agent, and then wiped from the edge of the glass with a clean rag, after wiping the edge clean, change the clean side of the rag to wipe the inside until the glass is completely clean.

2. Spraying alcohol: After the glass is wiped off, it is blurry and can be sprayed with alcohol. Spray the alcohol evenly on the glass and wipe it clean with a rag, or soak a towel in the alcohol solution, take it out and wring it out after wetting, and then wipe the blurry glass to dry it.

3. Newspaper wiping: The newspaper contains ink, which can wipe the glass clean, so after the blurred imprint appears on the glass, prepare one or two discarded newspapers, fold them, and wipe them from the edge of the glass until they are all wiped clean.

1. Towel wiping: the glass is blurred after wiping, which may be due to improper cleaning, at this time, the cleaning agent should be sprayed on the glass again, and then wiped with a clean rag from the edge of the glass Xiaoxun, after wiping the edge clean, change the clean side of the rag to wipe the inside until the glass is completely clean. 2. Spray alcohol:

After the glass is blurred after wiping, you can spray alcohol to treat it with caution or. Spray the alcohol evenly on the glass and wipe it clean with a rag, or soak a towel in the alcohol solution, take it out and wring it out after wetting, and then wipe the blurry glass to dry it. 3. Newspaper wiping:

Newspapers contain ink that can wipe the glass clean, so after a blurry mark appears on the glass, prepare one or two discarded newspapers, fold them, and wipe them from the edge of the glass until they are all wiped clean.

Plexiglass is blurry, and the most convenient thing to do is to apply a little toothpaste, rub it vigorously with a clean cloth, and it can become very bright. In the past, the surface of the hand became hairy and there were scratches, and this is how it was treated. When wiping, pay attention not to use too much force, wipe the direction consistently, clean and replace with new paste in time.

Secondly, you can also use a towel to stick hail and call for alcohol to wipe. There are generally two ways to blur the machine glass: 1. Sandblasting on the glass, first scrape the powder on the surface of the colored glass, and then wipe it dry with a clean cloth.

2. Sandblast and polish it with a steel brush, then rinse with water until it is smooth and transparent. 3. After sandblasting and grinding, rinse with water, then rinse with water, and finally rinse with water.