The home needs to be redecorated, and the location of the socket and closed circuit should be change

Since I don't know the structure of your house and the distribution of your lines, I can only give you some data, and you can calculate it yourself.

If the signal strength in your place is sufficient, you can use an amplifier, and a good amplifier is about 200 yuan. All indoor uses -5 cables,Professional high-quality lines are about every meter,Look at how far your home is from the incoming line to your TV socket、How many sockets to install you calculate。 Branches and distributors are about five grams, TV sockets are about three grams, and plugs and connectors are about one yuan.

The materials mentioned above are all professional and high-quality**. If you don't know much, it's best to ask a professional to design and install it for you.

The above does not calculate the other materials used by labor, these are local, and can only be estimated by yourself.

Good luck!

The first one, a major change, re-punch a hole in the wall, open a dark line groove, and then decorate the wall, so the advantage is that there are no traces, more beautiful, the disadvantage is that it is time-consuming and laborious, and the cost is a little higher. But since it's a renovation, it doesn't matter.

The second, walk obviously, with a plastic trunking staring directly at the wall. The advantage is that it is simple, fast and cheap, and the disadvantage is that it is not very beautiful.

This ** depends on the distance you move, now the salary of plumbers is very high, and the wage level is not the same in various places, it is estimated that it will be at least two or three hundred.

Before operation, cut off the power supply at home, need an electric drill, a new socket, test pen 1, first find the distribution route of the dark line, determine the position and then punch the hole positioning 2, use the test pen to detect whether there is current, no current and then pull out the wire about 5cm, put it into the socket base.

3. Remove the insulation layer on the outside of the wire, connect the socket and install it together with the base.

When decorating, there will be no re-slotting, only the nearest lead can be used, so that the cost is the lowest.

And there is no need to replace the whole house with 4 square or even 6 square wires, air conditioning, and kitchen can be replaced with 4 square wires, as for 6 square wires, general household appliances, such as water heaters, ** air conditioners can not be used, 4 square meters is enough.

Several problems in hydropower transformation:

Is it right or wrong for the designer to suggest that the bathroom be changed to three separations in order to increase the amount of construction and make money? ”

Is it right or wrong that designers recommend reserving sockets and faucets for garbage disposers, water purifiers, and water softeners? ”

The water supply pipe must be replaced with stainless steel, and the last time it must be a green PPR pipe, so that it is safe? ”

Are these questions right or wrong? Some of them can really improve our living comfort, some of them are just to make money for decoration companies, and there are more decoration traps, which we have sorted out into a small test, which does not take much time, but can effectively avoid falling into pits.

First of all, the layout of the wires is not for the pursuit of neatness, these wires are to be buried in the ground and the wall in the later stage, these are not visible in the later stage, even if they are neatly arranged, the more dangerous it is to be buried in the ground in the later stage, it is the place where the bend, and the dense lines below.

Secondly, if you groove on the load-bearing wall, it will also affect the stress point of the wall itself, causing damage to the structure of the house, and this is directly related to the change of the entire floor, so it is not a trivial matter, you must not do this when decorating, <>

If you encounter a place where you have to turn, don't use a right angle, it's best to use an obtuse angle, so that if you adjust the cable, it won't be so difficult. It won't break the wires. After listening to the master's words, it suddenly dawned on me, fortunately, the wires have just been repaired, and the wall has not been repaired, so if you don't need to re-groove, you need to invest more

This is fine, but if there is a place where the switch and socket have been installed before is not installed, then you have to repaint it after the renovation to look good, and it is no problem not to paint. Change the previous wires that should be replaced, and change the wires that should be changed.

Do you think the treatment of the wall can be simple What to do if it cracks after decoration The problem of wires depends on your main electrical box in** need to be changed** I think these things are not a simple way But pay attention to the quality and safety in the future.

Make a groove along the baseboard, and finish sticking the skirting.

If you don't want to make the project bigger, it is recommended that the wires be set to open wires. Topwires refer to parallel and mutually insulated overhead bare wires. Compared with cables, it has the advantage of low transmission loss.

However, it is susceptible to climate and weather influences and is sensitive to external noise interference. At present, it has been gradually replaced by cables.

If you want to make the wire a dark line, and you don't want to change the tile, the simple way is to groove along the tile joints as much as possible, and add white cement or porcelain white glass glue after laying the wire.

In this case, it is better to change the surface-mounted switch box. Of course, if the tool or technology is convenient, the switch box can also be dug and concealed, but the wire can only be open, unless you have the intention of replacing it with a new tile.

If the wire also wants to go dark and does not want to change the tile, the simple way is to groove along the tile joints as much as possible, and add white cement or porcelain white glass glue after laying the line.

If you don't want the biggest modification, then make a section of surface-mounted wiring duct to move it, and if you don't have high-power electrical appliances, you can directly buy a longer wiring board socket and fix the extension cord.

Decoration, I don't want to reprocess the wall, but I need to change a few wires, add a few sockets, and move the original switch position, is there a simple way?

Hello dear! We will be happy to answer your questions; After the installation of water and electricity is completed, it is found that the switch position is wrong, so how to change the switch position without destroying the wall, let pchouse explain it to you today. 1. Use PVC pipe and bracket to lay down from the wall, and the line on the top can be laid on the top with a pipe, if you want to consider the decorative effect, then it is recommended that the decorative lines are best laid along the wall, and now the role of the decorative lines is not bad.

2. Add a control line to the tube of the original switch into the lamp head, and replace the single switch panel with a double switch. It's simple, if you don't know how to install, you can find an electrician to install it for you. 3. Remove the socket panel cover, pull the socket wire out, then find a hard object to fix the junction box inside, then restore the socket, find plaster to fill the gap, and then use putty to find it.