What to do if the water goes into the socket, what to do if the water enters the socket

The socket is a necessity of our life, although we usually pay attention to the safety of the use of the socket, but also can not avoid negligence, such as accidentally making the socket water, the socket will make the electrical appliances unusable after the water is in, and the situation is serious and even will cause danger, so what should we do once the socket enters the water? Don't worry, there is! Let's teach you how to deal with water sockets.

Method steps.

1 7 step by step reading.

The first step after discovering water ingress must be to place the electrical outlet.

All closed, with a screwdriver.

Disassemble the socket shell, pay attention to the screws when disassembling, and do not roll away.

Use a hair dryer for hot air.

Check your nearest repair location. Ad.

If the situation is serious, after disassembling the panel, take a cotton swab to absorb water, and after the water is saturated, take the cotton and wrap it again and blot it dry and reinstall.

After drying, turn on the electric switch.

Insert the plug completely for the stable operation of the appliance on the one hand, and to prevent electric shock accidents on the other hand.

If the liquid you are dripped in is laundry detergent or dish soap.

and other corrosive liquids, or use cotton swabs to deal with first, but the cotton swabs should be dipped in water first, and then dried after processing.

After the repair, in order to avoid secondary damage, a layer of plastic baffle can be placed around the socket to prevent further moisture from penetrating.

1. The solution to the water ingress of the socket is handed over to you in detail, but in order to avoid this safety hazard.

Or pay more attention when using, try not to use it in a humid environment, if you can't avoid it, then take certain isolation measures for the socket, otherwise once you encounter water, it is either a short circuit or an open circuit, and when installing the bathroom bath bomb switch, you should also remember to leave a few more centimeters of position, because this switch is generally larger than the switch of the lamp, so as to avoid the size is not enough to install it, it will be troublesome.

2. At the same time, pay attention to check the inside of the socket before use, such as the socket inside the water, stained with dirt, dust, at this time it is best to clean it up before use, do not touch the socket when your hands are wet, you can set up some sockets with switches, so that you can cut off the power supply without pulling the plug, to a large extent, to avoid direct contact with the power supply, and will not unplug the wire hanging to affect the appearance. Sockets.

The best way to enter the water is: if it can be disassembled, it will be disassembled, wiped and dried, and if it cannot be disassembled, it can be naturally air-dried.

A socket strip is a strip.

Scientific name power strip. A socket strip is a type of socket, which is nothing more than a multi-hole socket formed by putting multiple sockets together. Such a combination has many benefits, it can be used for multiple purposes, saves both space and lines, and is a very simple and practical invention.

Usually a socket refers to a multi-hole socket with a power cord and plug that can be moved, while a socket usually refers to a fixed and mostly five-hole socket. Socket strips, also known as strip strips, commonly known as drag strips, are necessities of life. Now there are many businesses that produce power strips, such as TOWE, Siemens, etc.

If the water is not serious, take it out directly to dry, if the water is serious, first pour out all the water inside, then wipe it dry with a rag, and then use a hair dryer to dry all the water inside, and then put it back in its original state.

If the water enters the socket, then unplug the socket and put it in the sun, and dry all the water in the socket, so that it can be used normally, otherwise there will be a short circuit, which is very dangerous.

In this case, there should be an immediate power outage.

Then turn on the outlet.

Clean up open water. Then dry it with a hair dryer.

Install it again and you're good to go.

If there is a plug at the other end of the socket, the plug should be unplugged immediately, if not, the main switch in the house should be disconnected, and the socket should be disassembled and dried for a few days to allow the water to evaporate completely before use.

Plug and drain inlet water treatment method:

1. When the plug and drain enter the water, it must be repaired in time, if it is not repaired in time, it may lead to a short circuit in the plug and drain, which will cause a fire. If the problem of water ingress into the socket is very serious, the panel of the socket must be disassembled in time for treatment, and no moisture remains inside the socket strip.

2. When the plug and drain enter the water, the power of the plug should be turned off in time. Then use a screwdriver to unscrew the screws on the socket housing, and then remove the socket housing. When dismantling, you must be careful not to let the spring inside the socket jump away, if the spring jumps away, it is generally very difficult to find.

In addition, take care of the screws that have been removed, as they will need to be reinstalled later.

3. Next, you should use the hot air gear of the hair dryer to blow dry the water inside the socket from top to bottom, stop every 2 minutes, and continue to dry after the socket cools. At the same time, a cotton swab is used to absorb the water inside the socket to prevent some of the water in the corners from being blown dry.

5. The socket should not be used in a humid environment, otherwise it is easy to cause safety accidents. If it must be used, then it is necessary to take certain isolation measures for the socket row, so as to effectively avoid the socket from contacting water, if the socket is accidentally in contact with water, it is easy to short-circuit, or open circuit.

1. The most important step after getting water from the hole of the socket board is to turn off the power! Power off! Power off!

Important things are said three times). Disassemble the socket shell with a screwdriver, check the water ingress inside the socket, and pay attention to the screws when disassembling to avoid loss. 2. If the water ingress in the socket is not serious, use a hair dryer to blow from top to bottom, and stop blowing for 2-3 minutes to avoid burning parts due to the high temperature of the socket, and wait until the socket is cooled down and blow repeatedly until it is completely dry and can be used.

3. If the water ingress is serious, after disassembling the socket panel, take a cotton swab to absorb water inside the socket, the cotton swab can absorb most of the water, and can also absorb the water that is difficult to handle in the gap, and then repeat step 2 to dry the socket after absorbing the water.

4. If the socket is dripping with other liquids, such as laundry detergent, dish soap and other corrosive liquids, dip the cotton swab in water, first dispose of the liquid and then blow dry, if the cotton swab is found to have rust when wiping, it is recommended to replace the socket, and do not use it again if it is dangerous.

5. After the socket is thoroughly dried, open the electric switch and insert the plug, and plug in the electrical appliances at the same time to test whether the socket can work normally and stably.

6. After the socket is repaired, in order to prevent the socket from being damaged twice, add a layer of plastic baffle to the socket to prevent further moisture from penetrating.

The jack of the socket board cannot be used when there is water, because if it is used casually in the presence of water, then the possibility of touching the electricity is very large, so for the sake of safety, it is necessary to clean and dry the water in the socket before it can be used, so, how to clean and dry? If you are a person who understands the socket and understands the circuit, you can turn it on, wipe it clean with a dry towel or paper, etc., and then close it again and tighten the gong wire, if you don't have tools for the time being, and don't want to bother, then, you can carry the plug board and shake it a few times, and then use a hair dryer to blow it at the jack, and wait for it to dry before you can use it.

If you get water from the hole in the plugboard, you can only shake the water from the plugboard and dry it with a blow-air.

If you put it next to the heating in the north for a few days, you can continue to use it if the water is evaporated. Of course, for safety, you can also consider buying a new one.

If the hole of the socket board gets water, it should be removed and opened to dry before use.

Because it is a socket, it is most afraid of a short circuit and easy to catch fire, so you should quickly cut off the power supply of the socket, if there is no separate switch, then you can only cut off the power switch of the whole room. Then take the socket apart, air dry it with a hair dryer, or wipe it dry and reinstall it.

Use a hair dryer to blow or leave in the sun.

First of all, cut off the power supply, remove the socket, and then remove the fixing screws behind the socket, some sockets are purchased without fixing screws, which are fixed by plastic buckles, you can pry it down with a flat screwdriver, and then shake it hard, you can throw out the moisture inside, and then use a hair dryer to further dry it to install and reset.

The answer is to cut off the power supply immediately under the condition of ensuring the safety of electricity to avoid burning the power strip. 2.After cutting off the power supply, open the plug-in board and use a hair dryer to dry the water in the plug-in board, air dry to see if some of the electrical components inside are burned out, if there is obvious burn-out phenomenon, it is estimated that the plug-in board will have to be replaced, if there is no damage, the components are well protected, then close the plug-in board.

3.Close the power strip and turn on the power supply to see if the plug-in board can be used normally, whether the circuit can be smooth, and use the equipment to try to see if it can supply power to the electrical equipment in good condition. 4.

If it is used normally, then fix the power strip in a place that can avoid the water source to avoid the hidden danger of water ingress next time.

Question: Is it OK to blow directly with a hair dryer?

Here's how to get a little water into the socket if you accidentally get it:

Unplug the power supply from the socket and use a screwdriver to disassemble the socket housing; Use a hair dryer hot air setting to dry the socket; If the situation is serious, after disassembling the panel, take a cotton swab to absorb the water and then use a hair dryer to dry it and reinstall it; After drying, open the switch and plug the plug fully into the power source; After the repair is completed, in order to prevent secondary damage, a layer of plastic baffle is placed around the four sides of the socket to prevent moisture from penetrating.

It is best not to use it, it needs to be dried before use. Generally, this socket is dried by a hair dryer, and then tested for safety after being exposed to the sun for a few days before using it.

Turn off the power of the socket in time, and then use a screwdriver to unscrew the screws on the socket housing and remove the socket shell. Next, use the hot air shield of the hair dryer to dry the water inside the socket from top to bottom, stop every 2 minutes, wait for the socket to cool down and then continue to dry, and then install the socket shell back, and then install the screws back on.

The socket refers to a socket with one or more circuit wiring that can be inserted, through which various wiring can be inserted to facilitate communication with other circuits. The power socket is an electrical device that provides a power interface for household appliances, and it is also an electrical accessory that is widely used in residential electrical design, and it has a close relationship with people's lives.

First, turn off the power to the outlet. Turn off the power of the socket, disassemble the socket, be careful that the spring jumps away and cannot be found, use a hair dryer hot windshield to dry the socket and reinstall it to use. Then disassemble the socket and dry it with a hair dryer hot air shield.

The socket with water should be repaired in time, otherwise it may evolve into a short circuit and cause a fire. If the water ingress is severe, the panel needs to be opened for cleaning, in short, there can be no moisture residue. Re-purchase the socket to install.

The solution to water ingress into the socket is as follows:

Turn off the power of the socket and use a screwdriver to disassemble the socket housing; Use a hair dryer to dry the socket; If the situation is serious, after disassembling the panel, take a cotton swab to absorb the water and reinstall it; After drying, open the electric switch and fully insert the plug to prevent the occurrence of electric shock accidents; After the repair is completed, in order to prevent secondary damage, a layer of plastic baffle is placed around the four sides of the socket to prevent moisture from penetrating.

First of all, you talk about electrical sockets, is it a mobile power socket, or a wall socket? If it is water ingress on the wall of Figure 1, first look at the severity of the water ingress, spray water first disconnect the total power supply of the name of the seat power supply and then disassemble the socket to see the degree of water ingress, use a hair dryer to dry, use paper to try the water can cover the cover plate, close the power supply, if it is the mobile power supply in Figure 2, also unplug the power plug to open the socket, get rid of the water, the hair dryer can be used to dry, if there is water not dry, it will conduct electricity and cause the live wire and the neutral line to spark slowly, and the leakage will increase your electricity bill. If it is serious, it will burn the socket and short-circuit the power supply will cause a disaster.

After the socket enters the water, it should be dried or blown dry in time before it can be used, otherwise a short circuit will occur and the electrical appliances will be burned out, because the water is conductive.

Don't even use this plug-in until you find a way to dry the water. Wipe it with a paper towel, try drying it with a hair dryer, or let it sit for a while.

Hello, you can take out the hair dryer immediately to dry the socket, or use it again after a while.

You can use a hair dryer to dry, if you can move it to dry, you can also use it, and it will dry naturally in a few days.

First, unplug the outlet and let it air dry naturally or with a hair dryer.

A little water into the socket can be dried outside with a household hair dryer.

Let it air dry naturally or blow it dry with a hair dryer.

The socket should not be used until it has been flooded for at least one day. It is recommended to disconnect the power supply immediately and remove the outlet. Because the socket is prone to short circuit after water ingress, it will cause hidden dangers in electricity.

The socket can be connected to various wirings for easy connection with other circuits, so it will be used in every new home decoration.

Wall sockets are optional

1. When buying a wall socket, look at the internal structure, try not to choose the thumb type, but the panel type. Because the thumb type is easy to get stuck when it is reused, the panel type will not have this problem, and it will be more convenient to use.

2. In addition, when choosing, you should also check the electric shock of the socket. Generally speaking, the conductive parts are selected for greater electric shock. In addition, it is better to pay attention to the type of material for electric shock, if possible, it is better to choose silver-nickel alloy electric shock.

The contacts of this hybrid material have good electrical conductivity and are not prone to oxidation reactions.

In addition, the contacts of silver-cadmium alloy and sterling silver have poor conductivity and are prone to oxidation reactions, so it is not recommended to choose.