How much power does it generally need to leave for flashing, and how much power does it need to be b

The safety points are all full of brushes, and generally 50 should also work.

It's best to be fully charged, at least 50.

The more you need, the better!

Just fill it up.

1. It is best to ensure that the power is more than 70% of the power of the flashing machine.

Second, take card swiping as an example: use memory cards (SD, TF, etc.) to flash the machine, card swiping process:

3. Shut down, remove the SIM card, install the memory card, and it is recommended that the important things in the memory card should be backed up.

4. When shutting down, press the power button and the volume plus button at the same time, about ten seconds, and then let go.

5. Enter the recovery mode, i.e. REC mode.

6. Select Wipe Cache Partition to clear the cache.

7. After clearing the cache, select Wipe Data Factory and restore the factory settings.

8. Select "Install Zip from SDCARD", the power button is OK, then select Apply SDCARD:update, and the power button is OK, that is, select the flash package from the memory card to flash the machine, and wait patiently for it to be completed.

The tutorials all say that you want 60% or higher power, and sometimes it is only between 30 and 40%, and you don't want to charge, so you are used to using the electricity until the prompt, and then recharge. So I often flash 30 to 40%.

What about everyone? In fact, it doesn't take much electricity to brush the machine, there are 30 40%, and it is very unlikely that the power will be lost halfway, right? Unless there is a problem with the battery itself.

As long as your battery is fine, 10 percent is OK.

If you need to flash your vivo phone, it is recommended that the battery level be kept at more than 30% to avoid interruption when the battery is too low.

70% is the best, and if it's fast, 20% can also be brushed well.

The minimum is 70%, the more the better, mainly because you are afraid that you will run out of points on the way to the flash, causing hardware damage.

At least 40% Anyway, at least ensure that the power is not cut off during the flashing process.

Each machine is different, but the minimum is not less than 70%, if the power is cut off in the middle of flashing, then your mobile phone will become bricked or broken......

Generally, it takes about 10 minutes to flash a smart Android phone, and it may take half an hour and 40 minutes for other systems or non-smart phones.

This is mainly determined by the following aspects of the phone:

1. The brand, model, configuration, system, etc. of the mobile phone.

2. Flashing tools, different brushing tools have different flashing processes.

3. The size of the flashing package directly affects the flashing time.

Half an hour or so. If you don't back up **, the software. There will be less time.

It takes about half an hour to flash the machine, so the mobile phone needs to have at least about 30% of the battery, if the power is too low, it may lead to a failure in the middle of the flash, abnormality, resulting in flashing failure, can not turn on, etc., flashing is risky, choose carefully.

Hello. The normal flashing time is between 20 minutes and 40 minutes. The length of time depends on your proficiency.

Therefore, the battery of the mobile phone must be at least 50% above before it can be flashed. Otherwise. After a long time of flashing, the phone is out of battery, resulting in the failure of flashing.

Samsung's official website does not provide flashing software. Due to the risks associated with flashing, such as mobile phone problems caused by self-flashing, it may also affect the repair, so we do not recommend that you flash your phone by yourself.

Hello does not recommend using a third-party flash, using a third-party flashing software to flash the flashing package may lead to the phone, bricking, freezing, repeated restarts, missing functions, etc.

The minimum power is 70%, the more the better, mainly because you are afraid that you will run out of power during the flashing process, causing hardware damage.

More than 50% of the power can ensure that the flashing machine is completed, and if the power runs out, the machine will become a brick.

There are more things that the mobile phone flashes to run, and it consumes more electricity.,If the brushing process runs out of power, it's not good.。。。

In order not to run out of power when flashing, usually the tutorial requires half of the battery to be retained, for the following reasons:

Flashing is a continuous read/write flash memory, and the CPU is running at full capacity, which consumes a lot of power.

The charger does not work when the line is brushed, and only transmits data but not charging current.

It is not recommended to plug in the charger when swiping, although it can be charged, it will affect the power calibration when the flashing is completed.

If there is no power during flashing, file reading and writing will stop abruptly, which will have a great impact on the life of the flash memory. And it will cause file damage and need to be reflashed. If the destruction is the connotation module, it will not be able to charge and turn into a brick machine.

Therefore, most tutorials recommend reserving enough power for two brushes, about half of the total capacity.

Prevent you from running out of power during the flashing process.

If you run out of power, it fails, it's very clear.

Insurance, more than 50% of the flash, but I also have about 30% left when brushing, brushing only a few minutes, as long as the power is guaranteed for these minutes.

It doesn't take much power to flash the machine.

30% have been brushed.

Generally, more than 50% of the brush is more than insurance.