Can wall tiles be used to pave bathroom floors? Can wall tiles be paved on the bathroom floor

Generally use different, because of the floor tiles of the bathroom.

If you need to be non-slip, it is recommended to use all-over bricks.

Glazed bricks, matte bricks.

ceramic tiles and so on; Wall tiles should be made of waterproof materials, and glazed tiles are recommended. Floor tiles and wall tiles are matched to ensure that the decorative effect is consistent in the same environment. Why can't you use the same one? Let's take a closer look:

1. The water absorption rate of floor tiles and wall tiles is different.

Strictly speaking, wall tiles belong to pottery, while floor tiles belong to porcelain products, their essence and physical properties are different, whether it is from the selection of clay ingredients or to the firing process are very different. Generally, the water absorption rate of wall tiles is about 10%, which is several times higher than that of floor tiles with a water absorption rate of only 1%.

2. The place of use is different.

Generally, floor tiles are laid on the floor of bathrooms and kitchens, because of its low water absorption, so that bathrooms and kitchens will not be affected by water vapor and are less likely to absorb stains. And the wall tiles are made of glazed pottery, moisture content.

high, so its back is usually rough, so it is conducive to using adhesive to stick the wall tiles on the wall, and the floor tiles are not firmly pasted on the wall, and the wall tiles used on the ground will become difficult to clean because of the absorption of more water, so the two can not be mixed.

3. Pay attention to the laying sequence.

The floor tiles are pasted from the inside out, so if the ground has a slope or a floor drain.

If so, you should pay attention to arranging the water direction to find the slope; The wall tiles are paved from the bottom up, and for aesthetic reasons, the bottom bricks should be pasted last.

Generally, it can not be paved on the ground, first of all, the material itself is different, one absorbs water and one does not absorb water, and the hardness of the floor tiles with different toughness is very good, so it is recommended not to use.

Yes, under normal circumstances, the bathroom floor is to be tiled, but because there is more water in the bathroom, it is best to choose some non-slip tiles when choosing tiles, and it is best to use non-slip mats, which will be safer.

The wall tiles cannot be paved in the bathroom, and the bricks in the bathroom should be non-slip, and the wall tiles are not slippery and the size is not the same.

Wall tiles (porcelain tiles) should generally not be laid on the ground.

The reasons: 1. The porcelain piece is ceramic, with low mechanical strength, and it is easy to be damaged by pressure when laid on the ground;

2. The bathroom floor is wet for a long time, and the porcelain tiles are easy to expand and crack due to moisture;

3. The glazed surface of the porcelain tile is not non-slip.

It is best not to use it, the main reason is that it is not slippery, the wall tiles are relatively smooth, and it will be very slippery when exposed to water, which is easy to cause slip accidents.

Yes, it is generally paved with matching floor tiles.

Hello, dear, in the living room, dining room and other areas with a relatively dry environment, wall tiles can be laid on the ground. If it is a humid environment such as kitchen and bathroom, it is not recommended to lay the wall tiles on the ground, most of the wall tiles themselves are relatively smooth, and they are deficient in slip resistance, waterproofness and wear resistance, which will bring unchanged to the use and are prone to fall or breakage. On the contrary, if you want to lay the tiles on the wall, it is not recommended to do so, because the floor tiles are heavier than the wall tiles, and the paste will not be firm.

Therefore, when we lay tiles indoors, we must choose the right tiles and do not mix them up.

What kind of tiles are good for bathroom floors? The first thing to do is to choose tiles according to the size of the bathroom. If the area of the bathroom is 4-8 square meters, it is best to choose a tile with a relatively small size, such as 300mm and 300mm.

It is better not to choose large tiles, because when laying tiles, small tiles can well grasp the slope and make the floor drain drain smooth. Secondly, the bathroom floor tiles, it is best to choose glazed tiles with textures, this kind of bricks are easy to care, the appearance is similar to natural stone, not only non-slip, but also the style is relatively novel. Also, when choosing mosaic floor tiles, wall tiles should also choose mosaics, do not choose tiles of different styles, and maintain the integration of appearance.

The selection of tiles should be based on the area of the wall and the regularity of the wall, not too much, and it can be decorated. In addition, there are now some new foreign bathroom mats or toilet anti-slip mats are also good, the main function is hydrophobic anti-slip and beautification.

Is it good to have a bathroom with marble tiles throughout.

It is best to lay large non-slip floor tiles.

The difference between wall tiles and floor tiles is that wall tiles are mostly used for the decoration of indoor walls, while floor tiles are mostly used for the paving of indoor floors. Although the wall tile Fengchang and the ground touch orange brick are very similar in material, there are differences in the smoothness, wear resistance and anti-slip of the surface.

If you choose wall tiles as the paving material for the bathroom floor, then there may be the following problems:

1.Poor abrasion resistance. Wall tiles usually do not have good anti-wear performance, and are prone to wear and scratches after long-term use and cleaning.

2.Easy to slip. The surface of wall tiles has a high degree of smoothness, which makes it easy to slip even in dry conditions, while the bathroom is a relatively humid place and is more likely to cause slipping.

To sum up, although wall tiles can be used for wall paving in bathrooms, it is not recommended to use them as paving materials for bathroom floor tiles. It is advisable to choose floor tiles or non-slip tiles that are specially used for floor paving.

<> "Can all-porcelain wall tiles pave the bathroom floor?

No, there are the following reasons:

1. The firing process and physical properties of all-ceramic wall tiles and floor tiles are different, the wall tiles belong to ceramic products, and the floor tiles belong to porcelain products.

2. The water absorption rate of the two is different, the water absorption rate of wall tiles is about 10%, and the water absorption rate of floor tiles is about 1%, so that the floor tiles will not be affected by water vapor and will not absorb stains when cleaning.

3. The hardness, wear resistance and anti-slip performance of all-ceramic wall tiles are not as good as those of floor tiles, so all-ceramic wall tiles cannot be paved on the ground, otherwise Suilu is prone to problems.

Precautions for pasting all-ceramic wall tiles:

1. Wall tiles do not need to be soaked in water, it is different from ordinary bricks, and it cannot be brushed after soaking in water, so there is no need to soak in water during construction.

2. During construction, the adhesive should be evenly applied on the back of the tile, and then placed for a period of time to allow the adhesive to fully penetrate into the tile, so as to better adhesion.

3. Leave a gap of about 2-3 mm during construction, because the whole tile is easy to expand after heat, if there is no gap, it will cause the tile to appear hollow, falling off and other problems. In addition, the firing time of the whole tile is relatively long, and the surface is more or less deformed, and the seam can make up for this problem.

4. During construction, the wall should be cleaned up, if there are unevenness, it needs to be smoothed with cement mortar first, and then paved.

5. After the construction is completed, the tiles should not be collided immediately, otherwise the tiles are easy to loosen and cannot be better pasted with the wall. In addition, it is necessary to do a good job of maintenance, and only after the maintenance work is completed can people walk.

Kitchen and bathroom tile selection tips:

1. First of all, the surface color of the tile is uniform, and the surface finish and flatness should be good, otherwise it will be uneven after paving, which is not beautiful and has potential safety hazards. When choosing, if you set a certain specification of tiles of a certain brand, you should also randomly check to see if there is any breakage, but the boss will pay for the damage caused by the general transportation process.

2. The selection of kitchen and bathroom tiles can also be gently knocked on the tiles with hard objects, the crisper the sound, the higher the degree of porcelain ring, the better the quality, if the sound is dull and turbid, it is the next grade. Of course, this method is not easy to define the infiltration ridge, so it is not recommended.

3. Choose kitchen and bathroom tiles, and if conditions permit, you can also drop water on the back of the tiles to see how fast the water disperses and infiltrates after opening. Generally speaking, the slower the water absorption, the greater the density of the tile, the better the quality, on the contrary, the faster the water absorption, the worse the quality of the tile.

Precautions: kitchen and bathroom tiles should pay attention to the size when choosing, the size that is currently used more on the market is generally 300cmx600cm or 300cmx450cm, of course, some friends feel that they do not like to choose this size, want to design their own size, then they usually choose to paste the living room and other large bricks, and go to the processing plant to process and make the desired size. <>

Summary. Can I use floor tiles to stick to the bathroom wall?

FYI.