What happens when Whirlpool automatic washing machines don t work?

1. The drainage pipe is placed too low.

The drainage of the automatic washing machine is realized by the drainage pump, which is a drainage method. If the drain pipe is placed on the ground or placed too low, when the washing machine enters the water, the water flowing into the inner cylinder will automatically flow out of the machine along the drain pipe, and there is no water stored in the machine, the water level does not reach the specified height, the water level switch does not work, and the washing machine will always enter the water. As long as the drain pipe is hung up according to the requirements of the manual, it will work normally.

2. There is dirt blockage in the communicator.

When the water in the bucket reaches the water level, the water level pressure in the bucket cannot be controlled by the communicator, resulting in the water level switch action of the washing machine. At this time, the transparent plastic pipe connected to the water level switch should be unplugged, and then blow air to the water bucket to discharge the dirt to the water bucket, and discharge it out of the machine when draining. If the problem is still not solved after this treatment, you need to remove all the water level pipes and connectors, clean them with water and reinstall them.

3. The connector interface between the water level switch and the water bucket falls off.

Due to the vibration of long-distance transportation or the vibration during the use of the washing machine, the transparent plastic pipe between the water level switch and the water cylinder falls off at the water level switch port, so that the pressure in the water cylinder can not control the water level switch action through the communicator, and the water and electricity circuit is disconnected, so the washing machine does not stop flooding. Just reinstall the transparent plastic pipe installed on the right rear of the washing machine case and the water level switch interface. Drain the detergent from the bucket and restart the washing machine to return to normal.

There are many situations when the washing machine does not work, you can take a look at what instructions are on the washing machine, there will generally be prompts on it, there may be a power supply and pressure problem, and there may be an internal fault of the washing machine itself. It's best to get a professional to overhaul it.

There are many reasons why the fully automatic washing machine is not working. It may be that your faucet is not turned on, so the washing machine will not alarm when it runs out of water, or the motor is damaged.

The fully automatic washing machine is not working, first check whether the water inlet is empty, or if it is blocked, and then check if the power supply is connected.

If there is no movement at all, the power supply part should be considered.

I will never buy Whirlpool brand appliances, all the appliances in my house have been replaced, including induction cookers and rice cookers, for a few years, there is nothing wrong with the water heater, refrigerator, TV and air conditioner, except for the Whirlpool washing machine, F1 often appears, if you don't pay attention to where to wash it again.

Whirlpool Quanzhu Town washing machine is not working, this should be out of order, you can find a maintenance master to take a look.

First, the Whirlpool washing machine is blocked from **E920**, which generally means that it does not drain water, or no longer enters the water after the dehydration is completed.

Second, so zhi

Disorders can be caused by the following scenarios:

1. The lid of the washing machine is not closed, which causes the program safety self-test to fail to pass, and generates an automatic alarm and stops running. Please close the lid of the washing machine.

2. There are sundries in the drain pipe, which leads to the wrong closure and the washing machine is out of operation. The backsplash of the washing machine needs to be disassembled, the drain pipe removed, and the foreign object can be removed with a tool.

3. If the high-current lock fails, the computer version needs to be replaced. This situation cannot be repaired by self-inspection, and you can find professional maintenance personnel for maintenance.

Mine too, more than you.

It is recommended to replace the electric control board, and it is recommended to change the water level switch and water level sensor.

The version is unable to restore the right to direct on its own. Are your electronic control board and water level sensor original? Resulting in a change in the frequency of perception after **.

Is it a water level switch or a water level sensor Landlord?? 1. It is recommended to replace the original parts 4: Is E1 a drain alarm.

If it is not the original + inductive = there is a problem with the matching. The electronic control board is faulty. Can't match the originally set frequency?

2: What are you doing when you pull the tube off? , i.e., whether it is mechanical or inductive, the above description recommends checking each item one by one.

3.It could be the deterioration of the rubber of the water level switch or the water level sensor.

It must be the system.

If you have a problem, you still have to find customer service.

Summary. Hello, dear. Here's how to use Whirlpool automatic washing machines. 1. Before using the Whirlpool automatic washing machine, check whether there are hairpins, coins and other items in the clothes that need to be washed, and if so, you need to take them out.

2. Turn on the power of Whirlpool automatic washing machine, connect the drain pipe, and put the clothes in the washing machine.

3. Add laundry detergent or laundry detergent after the clothes are put in, and the amount of laundry detergent is determined according to the amount of clothes and the degree of dirt. Add laundry detergent and pour it directly into the washing machine, or pour it into the washing machine's own laundry detergent box, then turn on the faucet and close the lid.

How to use Whirlpool automatic washing machine.

Hello, dear. Here's how to use Whirlpool automatic washing machines. 1. Before using the Whirlpool automatic washing machine, check whether there are hairpins, coins and other items in the clothes that need to be washed, and if so, you need to take them out.

2. Turn on the power of Whirlpool automatic washing machine, connect the drain pipe, and put the clothes in the washing machine. 3. Add laundry detergent or laundry detergent after the clothes are put in, and the amount of laundry detergent is determined according to the amount of clothes and the degree of dirt. Add laundry detergent and pour it directly into the washing machine, or pour it into the washing machine's own laundry detergent box, then turn on the faucet and close the lid.

No response after pressing start.

Hello, dear. The solution to Whirlpool automatic washing machine does not work with water is as follows. You look at the kiss.

1. Do not enter the water treatment method a, turn on the power supply, the ears are close to the water inlet valve whether there is a "buzzing" sound, if there is, check whether the tap water is cut off, close the faucet, screw out the inlet pipe joint to check whether the filter screen of the inlet valve is blocked by foreign objects, if there is a pull out of the filter screen for cleaning, if the problem has not been solved, the water inlet valve should be replaced, the valve core of the inlet valve may be stuck and cannot be opened; b. If the inlet valve does not have a "buzzing" sound, you should try to replace the computer board at this time, and the problem may be on the computer board.

Can the water in the washing machine be discharged?

Yes, kiss.

How to put which button to press.

You take a picture of your pro. I'll tell you about it.

1. Press the power button first; 2. Find the "Program" column, click and select "Dehydration"; 3. Then press the start pause button, and the washing machine will start draining; 4. When the water in the washing machine is drained, the washing machine will pause for about five seconds, and then press the start pause button, the washing machine will stop working, and the drainage will be completed. Finally, press the power button and turn off the power.

Hello, dear. Just follow this method.

Hello, dear. You can do this by following this step. 1. Press the power button first; 2. Find the "Program" column, click and select "Dehydration"; 3. Then press the start pause button, and the washing machine will start draining; 4. When the water in the washing machine is drained, the washing machine will pause for about five seconds, and then press the start pause button, the washing machine will stop working, and the drainage will be completed.

Finally, press the power button and turn off the power.

Ask about custom messages].

Based on the operation panel provided, the method is summarized as follows:

Preparation: Before using the automatic washing machine, check whether there are hairpins, coins and other items in the clothes that need to be washed, if there are, you need to take them all out, put the clothes in the washing machine, and then add laundry detergent or laundry detergent after the clothes are put in, the amount of laundry detergent is determined according to the amount of clothes and the degree of dirt, and the laundry detergent can be poured directly into the washing machine;

Start operation: 1. Press the power switch of Whirlpool automatic washing machine;

2. Choose the washing method of the washing machine, the washing method of different washing machines is slightly different, and the mode can be switched with a single press;

3. Select the water level according to the amount of clothing, and similarly, press to select the water level;

4. After selecting the program, press the "Start and Pause" button of the Whirlpool automatic washing machine, and the washing machine will start working.

Notes:

1. After the laundry program is completed, the Whirlpool automatic washing machine will beep to indicate that the laundry work is completed.

2. After the Whirlpool automatic washing machine is finished, turn off the power of the washing machine, pull out the power plug of the washing machine, close the faucet, open the cover, take out the washing clothes, clean the barrel of the washing machine, and wipe the washing machine dry.

After the automatic washing machine is correctly installed, the specific operation and use method is as follows:

1) Plug in the power plug, put down or connect the drain, turn on the tap water, put the laundry, laundry detergent and additives (softener, bleach, etc.) into the washing machine, and close the cover;

2) Press the power switch, select the water level according to the amount of laundry to be washed, and select the program according to the specific conditions such as the dirty stroke and material of the laundry;

3) Press the "Start Pause" button and the washing machine will start working;

4) After the work of the selected program is finished, the buzzer will beep;

5) After the work, turn off the power switch, pull the power plug out of the socket, close the tap head, then open the cover, take out the laundry, clean the wire scraps filter bag, and wipe the washing machine dry.

Hello what is the reason for the ticking sound of the washing machine, and the bucket does not turn.

1。When the power is turned on, the indicator light does not light up, and the whole machine does not respond to the causes of the failure: (1) Power outage:

fuse blowing; Air switch tripping; The electrical outlet is damaged. Check each of the above items one by one, and if everything is normal, then check the washing machine. It is worth mentioning that when checking whether the power socket has electricity, everyone is accustomed to using a test pen to detect, and the neon lamp shines to think that the power supply of the city grid is normal.

When the AC voltage block of the multimeter is used to detect that there is no voltage display at the 220V input terminal of the computer control board, go to measure the power socket, and the result is that the no voltage indicator is absolutely displayed. So I disassembled the power socket and found that the copper sheet was seriously deformed and oxidized by the flashover, and the screws of the neutral wire connector were loosened and the flashover turned black, resulting in poor contact. Just replace it with a new electrical outlet, and the washing machine doesn't need to be repaired.

2) The power cord is not connected due to false soldering of the plug blade or broken wire (mostly at the root of the three-pin plug). Use a multimeter to measure and detect, and replace the three-pin plug or power cord after determining the open circuit. (3) The DC power supply circuit is faulty.

Disassemble the cover plate of the washing machine, remove the brain plate of the electric stool, detect the power transformer of the DC power supply, rectifier diode, filter capacitor, three-stage voltage regulator, etc., if any damaged components are found, they can be replaced with new parts of the same specification and model. 2。If the motor, water inlet valve, and drain valve are not working, it means that several bidirectional thyristors that control the load parts are not working.

The possibility of several trigger circuits being damaged at the same time is small, and the cause of the fault should be in the common part of the trigger circuit, such as the +5V public power circuit of the circuit, and the damaged parts can be found and replaced.

If the washing machine is plugged in and does not respond, it may be that your program is not set up properly, you can find the manual to reset the program.

Summary. Hello, it is a pleasure to answer your questions Whirlpool washing machine can't wash clothes, can't use what situation The answer to your question is: 1

Indicates that the dehydration imbalance cannot be handled automatically. Please put your clothes away and cover them manually. If the cover plate is not properly covered, please close the cover.

The washing machine will run automatically. 2.Indicates that the drain time is more than 5 minutes.

It may be that the drain pipe is not down, clogged or frozen, please put down or unclog the drain, open and close the cover once before the washing machine can continue to work. If no one intervenes, the washing machine will automatically turn off after about an hour.

Whirlpool washing machine can't wash clothes, can't use anything.

Hello, it is a pleasure to answer your questions Whirlpool washing machine can't wash clothes, can't use what situation The answer to your question is: 1It shows that the dehydration imbalance can be automatically dealt with.

Please put your clothes away and cover them manually. If the cover plate is not properly covered, please close the cover. The washing machine will automatically turn around.

2.Indicates that the drain time is more than 5 minutes. It may be that the drain pipe is not down, clogged or frozen, please put down or unclog the drain pipe, open and close the cover once before the washing machine can continue to work.

If no one intervenes, the washing machine will automatically turn off after about an hour.

3.It means that the set water level has not been reached after 30 minutes of water ingress. According to the instructions of the joke code "cleaning does not work hall wisdom" inspection, after the fault is eliminated, the cover can be opened and closed to restore the water dress up and answer. If no one intervenes, the washing machine will automatically turn off and after about 1 hour.

4.The water level pre-compression amount of the water level control beam spring controlled by the water pressure switch becomes smaller, and the pre-compression amount of the water level control spring can be solved as long as the screw is increased. When the elasticity of the water level control spring decreases or loses its elasticity, the water level control spring should be replaced with a more laughing and destroying operation.