What to do if the toilet leaks in the wall? What to do if the toilet leaks?

1.Poor raw materials of the water tank or old internal parts of the water tank will cause the toilet tank to leak. The toilet produced by low-quality materials usually does not show its quality on the outside, but there may be some small parts inside that are not used, and they are simply damaged.

Maintenance method: Separate the toilet tank, check one by one to see if the parts in the toilet tank are defective, if some parts are broken, can be repaired, it is best to replace the one that can not be repaired, if the pump tank is too defective, rotten more, replace the entire water tank, to avoid more serious consequences. 2.

Drain valve problem leads to toilet tank leakage The drain valve of the toilet bowl is mainly to control the water of the toilet tank, generally many may make the toilet drain valve problem, it may be the installation hole cracking and deformation, or the installation surface uneven and uneven and a series of reasons formed by the installation of carelessness. Maintenance method: Since many professional tools need to be used for testing, it is recommended to ask the toilet repair workers to carry out professional repairs as much as possible.

3.The leakage of the toilet tank caused by the failure of the sewer pipe may also be due to the problem of the sewer pipe below, the sewer pipe is a pipe connected to the toilet tank to transport water, and the possibility of leaking the toilet tank is also very high. Maintenance method:

Carefully check the interface between the toilet and the sewer pipe, whether it is loose, or whether the pipe is rotten, if the pipe is rotten, you need to replace the pipe from the beginning, if it is not connected, you can use some wire or the like or buy some fixing materials, and fix it. 4.The failure of the water scoop causes the toilet tank to leak to see what level the water scoop inside is at when the water tank is full, if the water inside is full, and the water tank is still entering the water, then it must be leaking.

Then pull the card position of the water scoop up and down with your hand, the sensitivity of the water scoop, if it is not smooth, or it is difficult to move, it is a problem with the water scoop. Maintenance method: can remove the equipment of the water scoop, clean it, if you don't understand the disassembly, just put dry water in the water tank, use dish soap, laundry detergent to clean it once, you can continue to use, can not be replaced.

To sum up, there are still a lot of reasons for toilet tank leakage, some are also because of their own reasons, either replace, or check the internal parts, for some other failures, you may not have the experience to deal with it well, at this time you can directly find the master, more safe. If you want to know more home information, please continue to pay attention to home after-sales service.

Toilet leak solution in the wall

If you want to fix it yourself, first use a knife to cut the glass glue at the joint between the toilet bowl and the floor tile, and then unscrew the bolts that hold the toilet open.

Lift the toilet a little, don't pull or push the toilet in place, it will be more troublesome if the sewer pipe is broken. Then check whether the sewer pipe is cracked, and then connect a section of the same thick PVC pipe, stick it to death with PVC glue, put the toilet on it and try it, the length may not be suitable, use a saw blade to see until the toilet can be placed stable, and the floor tile is close to the principle.

Finally, test the water, no leakage, glue the base to the floor tile with glass glue, and tighten the screws to fix the toilet. Take over the toilet bowl within three days, don't shake it back and forth, and wait for the glass glue to dry and you'll be fine.

It is recommended that you still don't get it, you are not a professional plumber who has never been in contact with these things, even if you repair the toilet, you may leak from the pipe if you don't connect the flange of the water pipe and the water tank.

If there is a water leak in the water tank, take out the parts inside through the panel mounting port, and replace the damaged ones in time. Or the water level is set too high, causing overflow, and adjusting the water level can solve the problem.

Hello friends, this is not a big problem, the leakage should be repaired, first find the cause and location of the leakage, and then repair, if it cannot be repaired, the toilet can be replaced.

Hope it helps.

Resolution. 1. The basin is easier to solve, use PVC50 pipes, connect with the original sewer pipes with elbows, and the ground should be slotted to reduce the height.

2. The toilet drain treatment of the wall row is more troublesome, considering the height of the ground, the sewer outlet on the original ground is generally discarded, and the 110mm vertical pipe in the corner of the wall is connected to the tee, and the back drain pipe of the toilet is connected with an elbow or directly, and the exposed thick pipe is either installed in this way, or a section of false wall is built to wrap it.

3. There must be a section of horizontal pipe for wall drainage, and the water is definitely not as smooth as straight down, so this section of horizontal pipe should be tilted as much as possible.

Toilet closure problem There is a problem with the closure of the toilet, it is likely that the rubber ball valve is broken or because the rubber gasket is aging, if the rubber ball valve in the toilet is broken, the rubber ball can be replaced after verification, the gasket is aging, and the new rubber gasket is replaced.

Can only open the wall, the toilet is broken? If it can be repaired, try to repair it, if it is not repaired, it is necessary to change the toilet, and replace the toilet hose under the toilet, which can be seen if it is a problem with the toilet, and if it is a pipe problem, it is to remove the pipe in the wall, so it is necessary to hit the wall.

If the toilet leaks in the wall, you can have diarrhea to block it, or call a plumber to fix it.

The toilet in the wall is leaking, so you have to turn off the main valve and then find a decorator. Dig it up and mend it all over again.

What you mean is that the pipe leading to the toilet is buried in the wall, and the water seeps out of the wall, so there is no other good way, you have to throw away the wall, find the leak, and then replace the water pipe and fitting, and that's it.

There's no such thing as a good solution. Only find a master to repair. Smash the wall open so you can find the leak. can be repaired, so this is the only way to do it.

The leakage of the toilet in the wall is a very troublesome thing, and the maintenance project is relatively large, but there is no good way to find the reason.

1. The leakage of the toilet tank may be caused by the broken inlet valve, and the connection between the float and the switch of the inlet valve is loose, resulting in the continuous inflow of water into the inlet valve, resulting in the leakage of the toilet tank. If the inlet valve itself is faulty, you can replace it with a new one.

2. The drainage valve gasket is aging, resulting in the drainage hole can not be well sealed, so there will also be leakage of the toilet tank. We can drain the water in the toilet tank, remove the drain valve, and replace the aging sealant pad.

3. If the inlet hose is not tightened, or the sealant at the hose is aging, or the inlet hose is damaged, it will also cause the water tank to leak. If the inlet hose is not tightened, we can tighten the hose, if it is caused by aging of the rubber pad or broken hose, we can replace it with a new product.

4. Damaged toilet tank will also cause water leakage. If it is an integrated toilet and the water tank is broken and leaking, we can replace it with a new toilet. If it is a squatting toilet, the squatting toilet and the water tank are separated, and you can directly replace the broken water tank.

1. Water tank leakage investigation method:

1. The rubber ball valve is broken, and a rubber ball valve with a matching model needs to be replaced.

2. The rubber gasket of the drain port is aging, and after long-term use, the rubber gasket will become thinner and thinner, and finally completely aged. Once the rubber gasket is aging and the tank will become less sealed, replace it with a new rubber gasket.

3. The link between the floating ball and the water inlet switch is loose, open the toilet tank, you can see a small ball floating on the water surface, and the small ball is connected to the water inlet with a water pipe. Check that the connection between the two is tight, and if it is loose, the connection needs to be tightened.

Second, the edge of the base leakage investigation method:

Scrape off the glass glue of the base first, then lift the toilet to check whether the sealing ring at the sewage outlet is damaged, replace the new sealing ring if it is damaged, and then apply glass glue at the junction of the toilet and the ground.

Align the toilet drain and sewer pipe, and finally seal the toilet base with glass glue.

Leaky toilets can lead to wasted water resources and environmental pollution, so timely measures need to be taken to fix them. Here are some possible workarounds:

Check the inside of the tank for loose or worn parts: If the parts inside the tank are loose or worn, it can cause the toilet to leak. The lid of the tank can be opened to check if the parts inside the tank are tight or need to be replaced.

Replace the gasket: There is usually a gasket at the bottom of the toilet bowl that is used to prevent leakage of sewage. If the gasket is old or broken, it can also cause the toilet to leak. The toilet can be removed and the gasket replaced.

Adjust the water level: Some toilets have an improper water level setting that can cause water leaks. You can check the toilet manual, adjust the water level to ensure proper use.

Ask a professional to repair: If the above methods cannot solve the problem, it is recommended to ask a professional to repair it. They can pinpoint the source of the problem by inspecting parts of the toilet, such as the drain system, tank, and plumbing, and provide a solution.

Please note that before any repairs are made, it is important to turn off the water source and turn off the power on the high gear to ensure safety. If you are unsure how to proceed with the repair, seek professional advice.

Here's how to fix it:1. If the bottom edge of the toilet is leaking, first scrape off the glass glue that is sealing at the original bottom.

2. Tanzhou then lifts one side to check whether the toilet sewage seal is tight or damaged.

3. If it is damaged, replace the sealing ring of the drain of the new toilet and install the sedan chair on the drain.

4. After the installation is completed, the connection should be coated with glass glue for sealing.