How to install the side toilet, how to install the side row of the toilet

1. The drain is required to be handled by the installer, and the bottom outlet of the toilet should be equipped with a special flange for the toilet or smeared with glass glue.

It is evenly matched with the sewer, glued at the bottom and around the toilet, and the gap between the toilet and the wall is even, placed properly and steadily.

2. After the toilet is in place, it is required that there is no leakage in the water intake, the water level is correct, the flushing is smooth, the switch is flexible, and the cover is stable.

3. Nowadays, the installation of the toilet is generally not equipped with anchor screws, but the reserved hole on the toilet should be blocked with glass glue to prevent it.

Stop flavouring. 4. If you need to install anchor screws, first use the special sealant installed in the toilet, and place it on the periphery of the drain port of the toilet base 2cm

The drain of the toilet should be directly opposite the first position of the drainage pipe, draw the position of the expansion bolt on the left and right sides of the toilet, take the toilet, punch the hole, bury the expansion bolt, pay attention to the newly punched expansion bolt embedded hole, it is possible to break the waterproof layer, it is recommended to pre-embed the expansion bolt at the same time, fill the sealant around the hole, and then bury the expansion bolt, first screw the expansion bolt, let the expansion bolt completely let go, strengthen its tension, and then unscrew the upper screw, put the toilet, and then directly screw the screw, cap, Maintain the overall appearance of the place.

5. At the intersection of the toilet and the periphery of the ground surface, because the toilet and the surface are not one, it can be transparent with grout.

The sealant is stirred to seal the outer opening of the toilet so that it remains integral to the floor surface, and it can also block the local toilet water on the periphery of the toilet.

6. After the toilet is installed, it should wait until the glass glue (putty) or cement mortar is solidified before it can be used with water, and the curing time is generally 24

Hour. 7. Install or debug the water tank accessories. Check the water pipe first, drain the water for 3-5 minutes to flush the pipe to ensure the cleanliness of the water pipe, then install the angle valve and the connecting hose, and then connect the hose with the installed water tank accessories water inlet valve and press the water source, check whether the water inlet and sealing of the water inlet valve are normal, check whether the installation position of the drain valve is flexible, whether there is jamming and leakage, and check whether there is any leakage and install the water inlet valve filter device.

The side toilet and the lower toilet are installed in a similar way. The choice of toilet is determined by the location of the sewer pipe reserved by the builder, and the lower row should be used if it is left on the ground, and the side row should be used if it is left on the wall.

The side toilet is a toilet with the outlet on the side, because the drain can be seen from the appearance, so many people don't like this style of toilet, but for people with small households, the side toilet is still a good choice. So how to install a side toilet?

1. The drain port needs to be placed flat by the installer. The bottom outlet of the toilet bowl should be equipped with a special flange for the toilet bowl or coated with glass glue, which should be evenly aligned with the drain. The bottom of the toilet and the surrounding area should be glued, and the gap between the toilet and the wall should be evenly placed. Straight and steady.

2. After the toilet is in place, there is no water leakage, the water level is correct, the flushing is smooth, the switch is flexible, and the cover plate is stable;

3. The toilet is generally not equipped with anchor screws. If you need to install anchor screws, first apply the film evenly with toilet sealant, draw the position of the expansion bolts on the left and right sides of the toilet, and drill holes to bury the expansion bolts. Be careful not to damage them. Waterproofing layer.

4. Install or debug the water tank fittings, first check the water pipe, drain the water for 3-5 minutes to flush the pipe, then install the angle valve and connect the hose, then connect the hose to the water tank fittings to connect the water valve and connect the water source, and check the water inlet valve. Check whether the water inlet and sealing are normal, and check whether the installation position of the drain valve is flexible.

1. When installing the side toilet, the distance from the center of the sewage outlet to the ground should be measured first, that is, the pit distance of the wall row. Be sure to consider the thickness of the tiles when measuring.

2. Before buying this kind of wall-row toilet, you must know whether the drainage method of your residential area is side-row, if not, you can't install this kind of toilet.

3. Because the water tank of the wall-type toilet is hidden in the wall, the material of the water tank, the water parts inside the water tank and the process of the water tank are relatively high. If it's poor, a series of problems will arise. Toilets are more troublesome in terms of maintenance.

1. Low noise: Since the water tank of the wall-mounted toilet is installed in the wall and has a wall barrier, the sound is naturally much smaller when flushing.

2. The toilet is easy to move: the wall toilet is much more convenient than the ordinary toilet, and it does not affect the spatial layout of the bathroom.

3. Small footprint: The wall-hung wall-hung toilet adopts the wall-mounted installation method, which occupies a small area and has a more open space.

4. Easy to clean: The wall-hung toilet is easy to clean, and there is no sanitary dead end, which is very in line with your cleaning personality.

Treat the ground drain as high as the ground, and then press the center of the outlet to draw a cross extension.

Draw a crosshair along the toilet outlet to the position where the edge of the toilet can be seen, 3 put the horse to the drain, and the crosshairs overlap.

Draw a line along the outside of the toilet bowl and remove the toilet.

Place the toilet sealing flange on the drain on the floor and make a circle of glass glue along the inside of the overall circle line of the toilet bowl.

Place the toilet on top of the crosshair, press the bottom edge of the toilet on the glass glue, connect the water hose, and install a corner valve at the water outlet on the wall to turn off the water for maintenance.

Do not use and keep the ground dry for 24 hours.

Detailed drawing of the toilet bowl

Tools: toilets, angle valves, hoses, rulers, rags, pencils, glass glue.

1. Open the packaging of the toilet, take it out, and then connect the hose to the back end of the toilet (the installation accessories of the toilet are mainly angle valves and hoses, which can be purchased by yourself or negotiated with the merchant).

2. Take a ruler to measure the distance between the wall and the ground outlet. After measurement, the distance between the bathroom wall and the sewage outlet is 400mm, which is exactly the 400 hole spacing of the toilet. If the distance is 300mm after measurement, you can choose to use the 300 holes on the toilet bowl to accompany the training distance.

In special cases, a shifter is also required.

3. Take a rag and wipe the ground around the sewage outlet clean to facilitate the installation of the toilet.

4. Install angle valves. After that, place the toilet bowl on top of the drain outlet, and after comparison, use a pencil to draw a line along the edge of the toilet bowl to facilitate installation. Then, place the toilet on the side of the sock.

5. Along the pencil line, put the glass glue, put the toilet on the glass glue, and compare it with the ground sewage outlet. After attaching it, the overflowing glass glue from the toilet bowl is tightly packed and kept beautiful.

Summary. 1. Check the levelness of the sewage pipe and the ground. Check whether there is any sediment, waste paper and other debris in the sewage pipe.

Also check that the restroom is installed in the front and back of the floor. If it's not flat, it's going to be leveled. 2. Determine the center line of the drainage pipe and determine the center of the drainage pipe.

The method is simple. Flip the toilet bowl over and draw a cross center line in the center of the toilet drain. Note that the lower cross center line should extend to the bottom of the toilet bowl and around the feet.

3. When fixing the bathroom, first align the toilet with the cross line of the floor drain to ensure that the bathroom is installed horizontally, and then press the sealing ring tightly. The next step is to secure the toilet bowl with foundation screws and a decorative cap. 4. After sealing the bottom and fixing the toilet, it is necessary to install a special sealing ring at the sewage outlet, or coat a circle of glass glue (putty) or cement mortar around it, and it is recommended that the ratio of cement and sand is to install the water tank accessories, and put the water to flush the pipe for 3-5 minutes.

In order to ensure that the tap water is clean, install the angle valve and the connecting hose, and then connect the hose and the installed tank accessories to the water valve. 6. The last step of commissioning and inspection is to check the bathroom, check whether the installation position of the drain valve is flexible, whether the water inlet valve and seals are normal, whether there is blockage and leakage, pay attention to check whether the water inlet valve is installed with a filter device, if not, it is recommended to use the installation. Notes:

1. After the toilet is installed, confirm whether there is a water leak. 2. Pay attention to the safety of installers during the installation process.

1. Check the levelness of the sewage pipe and the ground. Check whether there is any sediment, waste paper and other debris in the sewage pipe. Also check that the restroom is installed in the front and back of the floor.

If the shed is uneven, it must be leveled. 2. Determine the center line of the drainage pipe and determine the center of the drainage pipe. The method is simple.

Turn the toilet bowl and draw a cross center line in the center of the toilet drain. Note that the lower cross center line should extend to the bottom of the toilet bowl and around the feet. 3. When fixing the bathroom, first align the toilet with the cross line of the floor drain to ensure that the bathroom is installed horizontally, and then press the sealing ring tightly.

The next step is to secure the toilet bowl with foundation screws and a decorative cap. 4. After sealing the bottom and fixing the toilet, it is necessary to install a special sealing ring at the sewage outlet, or coat a circle of glass glue (putty) or cement mortar around it, and it is recommended that the ratio of cement and sand is to install the water tank accessories, and put the water to flush the pipe for 3-5 minutes. In order to ensure that the tap water is clean, install the angle valve and the connecting hose, and then connect the hose and the installed tank accessories to the water valve.

6. The last step of commissioning and inspection is to check the bathroom, check whether the installation position of the drain valve is flexible, whether the water inlet valve and seals are normal, whether there is blockage and leakage, pay attention to check whether the water inlet valve is installed with a filter device, if not, it is recommended to use the installation. Precautions: 1. After the toilet is installed, confirm whether there is water leakage.

2. During the installation process, it is necessary to pay attention to the safety grinding rules of the installer.

Installation steps: 1. Adjust the height of the water tank; 2. fixing screws; 3. Water supply pipe connection; 4. Drainage pipe installation; 5. Installation of protection devices; 6. Installation of sound insulation pads.

1. Adjust the height of the water tank. Side-press water tank: according to the thickness of the decorative layer xcm, the horizontal line from the upper part of the white box diagram to the bottom of the bracket adjustable foot is 2500px+xcm.

Top press water tank: according to the thickness of the decorative layer xcm, the adjustable foot from the top of the bracket to the bottom of the bracket is 2050px+xcm. The bracket adjustment leg is only allowed to be adjusted up to 500px without being particularly lengthened.

2. fixing screws; The installation of the water tank bracket is mainly fixed by 4 screws, two on the upper part of the bracket and two on the support feet; At the same time, all screws on the tank bracket must be tightened. When installing, it is necessary to ensure that the surface of the water tank bracket is horizontal and the façade is vertical.

3. Water supply pipe connection; The water inlet of the water tank should be connected with the water supply pipe (hard pipe) of the water tank and the water inlet angle valve. It is strictly forbidden to install the angle valve in the water tank outside the box, so as not to cause the water tank to be unable to open and close the angle valve during cleaning and maintenance.

Strict tenants do not allow hoses to connect water supply pipes to tank angle valves, pipe pressure and hose quality may cause leakage, in case of leakage, false walls need to be destroyed to repair.

4. Drainage pipe installation; If the concealed water tank is installed in the original pit, the short pipe connecting the potato tank and the drainage pipe must be larger than 90 to prevent blockage.

5. Installation of protection devices; All protective devices should be installed before the false wall is made and the decorative layer is installed.

6. Installation of sound insulation pads. The fake wall is decorated and tiled. Then attach the soundproof mat to the decorative wall. Cut off any excess acoustic pads after installation.