How to dredge the sewer when it is frozen? How to thaw sewer ice quickly?

Here's the answer:Dissolution method of sewer freeze:

1. Sprinkle industrial salt or edible salt into the sewer.

2. Heat the sewer with a heater or other things that can generate heat.

3. Slowly melt with boiling water, and blanch the pipe with hot water. If you can't reach the pipe, remove the water meter, insert a thin plastic pipe into the water pipe, plug the water and heat the water from the thin plastic pipe, and if it is not deep, it can be melted.

Sewer pipe blockage is a very common problem in daily life, and sewer dredging is generally divided into several types:

1. If the pipeline is accidentally dropped into a foreign object or caused by installation error during the new installation of the pipeline, the pipeline dredging machine is generally used to directly dredge or replace the pipeline;

2. Some pipelines will be scaled after a period of use, which will make the inner diameter of the pipeline thinner and affect the normal sewer discharge. Sewer dredging is widely used in restaurants, hotels, homes, etc.

Salt can be used to unclog.

The best thing to use is industrial salt or edible salt, scatter a little into the blocked sewer, take it slowly, don't sprinkle too much at once, and then wait patiently.

Use heaters or other things that can heat up the sewer, but it should be noted that these must be used according to the situation of the sewer, some sewers may be plastic pipes, so you should observe them in real time when you use them.

1. Use hot water.

Cover the faucet and water pipe with a towel or damp cloth and unscrew the switch. Then start from the faucet, water it with warm water a few times, then take a pot of hot boiling water, and pour it evenly back and forth on the water pipe.

2. Use a hair dryer.

If the tap water pipe at home is ppr material and slightly frozen, you can use a hair dryer to blow your hair, be careful not to blow in one place, but up and down, so that you can thaw the tap water pipe.

3. Use a blowtorch.

The blowtorch method is suitable for cast iron water pipes.

4. Heating in the tube.

For thicker pipes, you can use the pipe heating method, that is, after unloading the pipe interface, inject warm salt water into the pipe, and the water pipe will thaw quickly. However, this method is cumbersome and should be considered with caution.

1. Industrial salt.

When the sewer is frozen, you can sprinkle industrial salt or edible salt into the sewer pipe, and then put a small steel wire into the water pipe and stir it slowly, and the ice in the pipe will melt quickly. You can also pour boiling water into the sewer pipe and put a wire into the pipe at the same time, and then poke the wire into it while pouring the water.

2. Thermoelectric hair dryer.

When the sewer pipe at home is not frozen for a long time, or the freezing situation is not serious, you can also blow the thermoelectric hair dryer against the pipe all the time, which can make part of the ice in the sewer pipe thaw quickly.

3. Wrap a hot towel in warm water.

You can wrap it in a hot towel and pour warm water slowly over the pipes, but do not bake them over fire or with boiling water, as this will burst the pipes and meters. This method is suitable for both water pipes and sewer pipes that are frozen.

4. Plug the mouth of the ditch with a quilt.

The pipes of many residential buildings are underground, and the underground pipes are frozen, mostly because some ditches do not have cold protection measures. Residents can find some old quilts to plug the gutter mouth and use it to keep warm.

5. Turn on the faucet.

Turn on the faucet and try to use the current to slowly melt the ice inside the tube. Reminder, if the faucet is also frozen, don't force it, be sure to thaw it first; Secondly, it should be noted that if the same water pipe is connected to both hot and cold water faucets, remember to open them to reduce the pressure in the pipe.

The method of rapid thawing of the sewer is as follows: 1. Pour hot water on the water pipe repeatedly, and the ice in the water pipe may melt after pouring it several times. 2. If there is a plug near the water pipe, you can directly use a hair dryer to blow the water pipe, and pay attention to the plug not to enter the water, otherwise it will be short-circuited and electrocuted.

3. Cover the pipe with a wet towel, and then turn on the water pipe switch, and the water pipe may come out normally after a while. 4. Pour hot salt water into the water pipe, the salt water has the effect of dilution, and the ice may melt after pouring it a few more times. 5. Wrap the thermal insulation foam on the water pipe in advance, as long as the water pipe is effectively wound with the thermal insulation foam, it is not easy to freeze in the later stage.

When the temperature is very low, the sewer pipe is easy to be frozen, resulting in its inability to drain normally, so how to dredge the sewer pipe when it is frozen? 1. How to dredge the sewer pipe when it freezes 1. The sewer pipe is blocked, we can pour some edible salt into the sewer pipe mouth, and the salt can make the ice melt faster. 2. I have learned that you can insert a water pipe at the mouth of the sewer pipe, slowly pour the water from the hot stove into the sewer pipe, and then insert the wire into the pipe to dredge it, and you can dredge the frozen sewer pipe.

3. You can also wrap the frozen sewer pipe with a wet cloth, and then pour hot water on its surface, and pour it several times to dredge the frozen pipeline. When pouring hot water on the sewer pipe, do not use boiling water, otherwise the water pipe is prone to cracking. 4. If the underground sewer pipe is blocked, it is best to ask a professional to thaw and dredge.

2. How to avoid the pipeline being frozen 1. The temperature is low in winter, so you can use heating equipment to maintain the room temperature to avoid the temperature being too low and the sewer pipe is frozen. For example, in winter, it is best to turn on the heating at home for heating, if we do not need to use the heating when we go out, then we can turn on the anti-freezing function of the wall-hung stove, which can also avoid the pipes from being frozen. When the temperature is lower, we can wrap the exposed pipes with a layer of insulation cotton to keep them warm.

2. As long as the water in the water pipe is kept flowing, it can also avoid the pipe from being frozen. Consider turning on the faucet in your home so that the water in the pipes keeps flowing. When turning on the faucet, it should be noted that the faucet can only be opened a little bit, and the basin can be used to fill water under the faucet to avoid wasting water resources.

Sunbathe. If the water pipe is frozen outside, you can dry it in the sun and let it thaw naturally. The premise is that the temperature must be above zero, so that there is a possibility of natural thawing, if it is still below zero, there is little hope of thawing yourself.

2 4 hot water. Pour hot water evenly back and forth on the water pipe, being careful not to burn yourself. If the freeze is more severe, you can try pouring it a few more times.

However, it is important to remember that boiling water should not be used to scald the bridge to avoid the bursting of the pipe. 3 4 Saw off the frozen water-sensitive high round pipe. If the length of the water pipe where the fruit is frozen is less than 50 cm, it can be sawed off and replaced with a new one.

4 4 pour salt water. Pour some warm salt water into the drain to speed up the melting of the ice.