The faucet in the kitchen is blocked, is there any way to unclog it?

It is believed that everyone will install a faucet in their home, whether it is in the bathroom or kitchen. However, the faucet will be clogged after being used for a long time, and the water will not be so smooth at this time, and many people often don't know what to do. In fact, the faucet in the kitchen or bathroom is blocked, most of which is due to the hard water quality, and it will be blocked by scale after a long time, and it is easy to solve it, which is common vinegar in our daily life.

Tomato sauce and the like can all be used to unclog faucets.

First of all, most of the faucets will have a joint, which is the filter screen and foaming net of the faucet, which can be unscrewed off, and can be unscrewed counterclockwise by hand. If it is not easy to screw, it is because the screw mouth is blocked by limescale, and you can spray vinegar or citric acid.

Or soak in ketchup for a while to loosen the dirt. No matter how bad it is, you can wrap it with a rag and use a wrench.

It should be noted that it must be wrapped in a cloth, otherwise the tool will leave marks on the faucet.

After unscrewing, we will find that the filter screen and foaming screen like the one above, there will be a lot of impurities on the filter screen, and the mesh may be blocked by limescale, at this time, it needs to be rinsed, or soaked in vinegar for half an hour before cleaning. Note that there will be a rubber pad inside, don't get rid of it, if it does, the faucet will not be tightly sealed. The rubber mat is also very dirty and can be cleaned thoroughly with a brush.

Wash it and put it back on, and you can restore a smooth water discharge.

In addition to the inside, the outside of the kitchen faucet is often stained over time, in fact, this is also the result of the accumulation of limescale over a long time, and there is a very clever way to use toothpaste to wipe it off. This is because the toothpaste contains abrasives such as silicon, and the fine abrasive particles can easily erase the water stains on the surface of the chrome plating, leaving it as clean as new in the blink of an eye.

Of course, these are post-remedial measures, if you are in a place where the water quality is hard, you can also install a filtration device or a water softening device at the inlet end of the tap water, which can isolate all kinds of calcium in the tap water, which will effectively reduce the blockage of the faucet.

Limescale blockage: Remove the faucet, pour some hydrochloric acid into it, and rinse. If there is no hydrochloric acid, you can soak it in white vinegar to remove limescale. Faucet quality problem: close the main valve and change the faucet.

Please ask professional maintenance personnel to provide door-to-door service and prescribe the right medicine.

Remove the faucet by yourself, see if there is any foreign object blocking the water port, wipe it, etc.

Just go to the hardware store and buy a new faucet and replace it.

It may be that there is too much crumbs and debris flowing into the kitchen during daily use, and it is blocked at the turn of the water pipe, so you can try to remove it and clean it up.

It's getting colder, and the kitchen drain is clogged again. Today I will teach you a simple treatment method to quickly unclog the sewer.

1. You can take a chemical method to prepare baking soda and white vinegar, mix it with hot water, and pour it directly into the sewer pipe, because whether it is white vinegar or baking soda, it can dissolve stains.

2. You can take a physical method to prepare a round wooden stick, which is slightly smaller than the diameter of the sewer pipe, and can be stretched in. Poke it back and forth a few more times to dredge some of the oil in the pipeline.

3. If it is useless by chemical or physical methods, unscrew the joint of the water pipe, remove the hose, and clean up the blockage in the sewer pipe.

Hello dear. I'm the answerer, Xiao Xiao, and I'll answer your questions.

The way to dredge after the faucet is blocked is to pour vinegar into the cup prepared in advance, put a cotton ball in the cup, soak it all, keep it for 5 minutes, take out the cotton ball, and then stuff it into the outlet of the faucet to be cleaned, and wipe the edge of the faucet with a rag. 2 The faucet is the popular name of the water valve, which is used to control the size of the water flow, and has the effect of saving water. The replacement speed of faucets is very fast, from the old-fashioned cast iron process to the electroplating knob type, and then to the stainless steel single-temperature single-control faucet, stainless steel dual-temperature double-control faucet, kitchen semi-automatic faucet.

Question: I can't pour vinegar into this.

<>You're all broken.

Dear, it is recommended to change to a new one. This head is broken.

1. Rational use of vinegar cleaning. Pour the vinegar into the prepared cup, not too much, then put a cotton ball in the cup, soak it all and hold for 5 minutes. Take out the cotton ball in the cup, and then stuff it into the outlet of the faucet to be cleaned, remember to reserve a little cotton ball, otherwise it is not easy to take out, and you can take it out in about fifteen minutes.

Remove the cotton ball, you can clearly see the dirt and debris on the cotton ball, soak it in vinegar with a clean rag for 2 to 3 minutes, and then wipe the edge of the faucet with a rag, which can well remove the dirt on the edge of the faucet. Turn on the faucet, at this time you can see if the faucet is running normally, if not, use the above method to clean again.

2. Clean the filter screen. Generally speaking, the newly installed faucet will have a layer of filter, the use of the filter screen is to prevent the water from splashing during the use of the faucet, but the filter screen can not only prevent the splash, but also adsorb a lot of dirt, resulting in the faucet blockage, then the filter needs to be cleaned.

1. Unscrew the filter of the faucet counterclockwise (if it can't be twisted, pad a piece of cloth and twist it with wire pliers). 2. The filter mouth is downward, and the plastic filter element is pushed up with your thumb forcefully. 3. Place the plastic filter element under the faucet, gently brush it with a toothbrush, and wash off the fine scale layer on it.

4. Assemble the cleaned filter and re-screw it onto the faucet. <

1. Unscrew the filter of the faucet counterclockwise (if it can't be twisted, pad a piece of cloth and twist it with wire pliers).

2. The filter mouth is downward, and the plastic filter element is pushed up with your thumb forcefully.

3. Place the plastic filter element under the faucet, gently brush it with a toothbrush, and wash off the fine scale layer on it.

4. Assemble the cleaned filter and re-screw it onto the faucet.

The solution to the inside of the faucet that is blocked:

1. There is a joint that can be screwed on at the place where the water comes out of the faucet, and you only need to gently unscrew this joint in the counterclockwise direction.

2. Further split the unscrewed faucet interface. There are generally a small number of parts inside the interface of the faucet, and these small parts are the important reasons for the blockage of the kitchen faucet.

3. Take away the 2-layer iron sand net inside the faucet, you will find that there are many tiny sand particles on the iron sand net, and these tiny sand particles block the sand net, which also reduces the speed of water flow and the water output of the faucet. Generally, vinegar is used to soak the iron sand mesh in vinegar, and then a needle is used to pick out the larger sand particles after about an hour, and then the surface of the iron sand mesh is washed with flowing water to ensure that the smaller sand particles inside can be washed away.

4. After ensuring that the water outlet hole can be unimpeded, first put the green rubber pad below, screw the green rubber part, and then put the 2 layers of iron sand mesh into it in turn, and the interface of the faucet is completely spliced.

5. After splicing the interface of the faucet, reinstall it on the faucet, and then turn on the switch of the kitchen faucet to find that the water flow of the faucet has become larger, and the faucet will no longer have the problem of blockage.