The toilet is not clogged, but what happens if the flush is not strong?

It can be repaired in the following ways:

Look at whether there is a trap in the pipe, because the toilet itself has a trap, and there is air between the two traps, and the air pressure cannot be pressed, so it is impossible to get into the water. Solution: Open the vent at the back of the toilet.

Or you can place a plastic bottle full of water in the toilet tank to make the water level in the toilet tank higher; You can also adjust the inlet valve inside the toilet tank, as long as the screw on the inlet room is rotated in a clockwise direction, you can also make the water level in the toilet tank higher.

1. The toilet lever is loose

At present, most of the toilets are pressed flushing, there is a press button on the toilet tank cover, the back of the button is the pressure rod, the length of the pressure rod can be adjusted, the length of the adjustment is large, the water output is larger when pressing, and the water output is smaller when pressing shorter. And this pressure rod is threaded, may be in the process of long-term use, the slip wire loosens, resulting in a smaller length, then in this case, when we press this flush button, due to the valve opening is relatively small, the water flow is relatively slow, there will be, the toilet is not blocked, but the flush is weak.

2. Siphon toilet, the flange of the sewage outlet is not tightly sealed

Siphon toilet, its main working principle is an S bend drainage pipeline inside it, and has a long vertical downward pipeline, when the toilet flushes, the water enters the drainage pipeline, which will produce a siphon phenomenon and suck the dirt away. This is mainly due to the tightness of the suction pipeline, which uses the gravity and atmospheric pressure of water to produce a siphon phenomenon. And if this suction line is breathable, then its suction power will be reduced.

In the siphon toilet, the most likely problem is that the flange of the sewage outlet is not tightly sealed, and there is ventilation, which will lead to weak toilet drainage.

3. There is dirt on the inner wall of the toilet drainage pipeline or the sewage pipeline under the toilet is blocked

Although the drainage pipeline is not completely blocked, the rough inner wall of the pipeline will inevitably increase the resistance to the water, resulting in a relatively slow water flow, at least much worse than the inner wall of the smooth pipeline. This can also lead to a weak drain in the toilet.

The solution to the toilet flushing weakness:

1. Check and adjust the length of the toilet flush key pressure lever.

When the toilet flush is weak, we can first check the length of the toilet flush button lever. Lift the lid of the toilet bowl and turn it upside down, adjusting the two levers separately. Generally, clockwise twisting is shorter, and the amount of water will be smaller, and counterclockwise twisting is longer, so that the water output of the toilet will be larger.

Adjust to the appropriate position and tighten the nut to fix the pressure rod. This solves the problem of weak toilet flushing.

2. Check the toilet sealing flange.

For the siphon toilet flushing power, it is necessary to check the sealing flange at the sewage outlet, it is generally a rubber flexible sealing ring, the toilet can be seen only when it is removed, if it is aging or the installation is not in place, then directly replace a new one, and install the toilet well, no air leakage, you can solve the situation of weak drainage.

3. Clean the toilet drain thoroughly.

Although the toilet can still drain, it does not mean that it is not blocked, nor does it mean that the pipe is not blocked, it may just not be completely blocked. Then this requires a thorough cleaning of the drain line. You can use a special detergent, rinse many times, or use a special tool to clean, in short, the inner wall of the toilet drain pipe should be smooth, there is no scale and dirt attached, and the pipeline is unblocked, so that the water flow will be very smooth, and there will be no weak flushing.

1. If the toilet is not blocked, but the flushing is still weak, it may be caused by insufficient water pressure. In this case, we need to adjust the water level of the tank appropriately. The simple way is to raise the water level by filling a bottle full of water directly in the tank.

2. Or you can also adjust the screw of the inlet valve to increase the water level, but pay attention to a certain distance from the overflow pipe of the drain valve, such as leaving a space of 10 mm.

If you still can't solve the problem, it may be that the toilet is not good, and the flush volume itself is insufficient. In fact, if you choose a toilet with better quality, correspondingly, the momentum and sewage discharge capacity will be very strong.

What to do if the toilet flushes weakly turns out to be a problem here, and you can easily solve it at home.

1. If it is a toilet that has just been installed, it may be caused by improper installation of the toilet, and you need to find an installer to check the cause and deal with it. 2. It may be that the spring of the flush button is aged, there is no elasticity, and it cannot be pressed to the end, so it is not energetic when flushing.

How to deal with the toilet flushing power:

1. If the water level of the inlet valve is too low and the water outlet is weak, the corresponding water inlet valve should be removed, the buckle should be removed and rotated counterclockwise, and a height of it should be adjusted appropriately, and then the inlet valve body should be rotated clockwise to connect the filter and the water inlet pipe, so that it can be.

2. If the toilet is clogged and the flushing is weak, you can use a dredge to dredge it, or find a longer plastic water pipe, connect the tap water at one end, and plug it into the toilet mouth at the other end, block the toilet mouth with something like rags, open the tap water, and use the water pressure to dredge the pipe.

3. If there is too much dirt in the toilet bowl and the flushing is weak due to not being cleaned up in time, it is recommended to use some baking soda.

or white vinegar for cleaning. It is not recommended to use steel wool balls and detergents, etc., which will cause damage to the glaze of the ceramic.

The toilet is not clogged, but the weak flushing is caused by insufficient water pressure.

The water pressure is insufficient, and the water level of the water tank needs to be adjusted appropriately, and the water level can be increased by filling the tank with a bottle full of water. You can also adjust the screw of the inlet valve to raise the water level, but be careful to keep a certain distance from the overflow pipe of the drain valve, such as leaving a space of about 10 mm.

Ways to prevent clogged toilets

1. Do not pour leftovers into the toilet. Usually when we use it, we should install its operation method to use. Don't pour leftovers, bones, hard objects, hair, etc. directly into the toilet bowl just because you are greedy for convenience.

These practices are all wrong, and they will all cause the blockage of the toilet drain to a certain extent, which will affect our daily use. And if the oil stain in the leftover garbage is stained on the toilet wall, it is not easy to clean, and the long-term accumulation of dirt can easily lead to poor toilet flushing or block the water channel, which will also affect the aesthetics and service life of the toilet.

2. Place a paper basket next to the toilet. When the toilet is installed, it is recommended that you should add a paper basket to it as soon as possible, such as paper, sanitary napkins and other sanitary garbage, if it falls into the toilet, it is easy to cause blockage, so it is necessary to place a paper basket next to the toilet, which can effectively prevent the toilet from being blocked. Since the bathroom environment is humid and easy to breed bacteria, it is recommended that the garbage in the paper basket should be cleaned once a day, so that the environment of the bathroom can become cleaner.