What is the fault of the washing machine with E2

It refers to the overtime of draining (if the water is drained for more than 6 minutes, the alarm can be lifted by opening and closing the door cover once).

Under normal circumstances, if the washing machine is drained for more than six minutes, this fault alarm will appear. For such malfunctions, the alarm can be lifted by opening and closing the lid of the washing machine only once. But it still can't be solved, so check if the drain pipe is down or deformed, and if so, put it down or replace it.

Possible Causes:

The drain pipe is not lowered, resulting in the water not being drained;

The drain pipe is deformed or twisted, resulting in excessive drainage time;

The drain valve is clogged and the water cannot be discharged;

There is a problem with the circuit, etc.

Troubleshooting of washing machines that cannot be dehydrated.

The laundry is in an unbalanced state during the washing process. Elimination: Before washing, you can put less clothes, don't stuff too much at once, so as not to cause an imbalance in washing. But the dehydration effect is not good.

The safety switch on the top cover of the washing machine is damaged. During the dehydration process, try not to open the top cover, so as not to damage the top linkage switch.

Clogged laundry drainage. Method: Remove the drain filter for cleaning, flush the drain with water to remove debris in the drain valve.

The water level switch cannot be reset. Solution: Contact the after-sales point.

The washing machine could not be dehydrated due to a faulty motor. Method: Try opening the back cover of the washing machine and moving the pulley by hand if it doesn't get stuck.

When the power is turned on and the motor hums, but does not rotate, it means that the motor is short-circuited or damaged, or the motor circuit is not connected to the capacitor. At this point, cut off the power supply, remove the motor belt, and restart. If the motor still does not rotate or the speed is low, it is a motor failure and the motor should be repaired or replaced.

E2 After 6 minutes of drainage, the water level sensor still cannot be reset Open and close the door cover, check the drainage pipe, etc.

Hello. Failure** Cause Resolution.

E1 Overtime for water inlet or replenishment Open and close the door cover, check the water inlet valve, etc.

E2 After 6 minutes of drainage, the water level sensor still cannot be reset Open and close the door cover, check the drainage pipe, etc.

E3 Dewatering Front Door Closed Close the door cover.

E4 In the same process, the third collision occurs with the barrel closing the door lid and distributing the laundry evenly in the bucket at the same time.

E5 Low Voltage Protection Automatically resumes operation when the grid voltage rises.

e6 Insufficient appointment time Press the appointment button to increase the appointment time.

E7 Non-empty bucket state during weighing correction Restore empty bucket status.

E8 Water Level Sensor Damaged or Poor Contact Check that the water level sensor and its circuit are properly connected.

E9 Automatic weighing failure Check the signal transmission line system assembly If there is no abnormality, replace the computer board.

e10 does not set the present tense Set the present time before you can set the appointment time.

e11 The interval between the present time and the appointment time is too short: Set the interval between the present time and the appointment time to exceed the laundry time.

F0 Power Switch Failure cannot be lifted, replace the power switch.

F2 EPROM self-test error cannot be canceled, replace the computer board.

F4 Zero-crossing detection line failure cannot be lifted, replace the computer board.

F8 Water level sensor is damaged or in poor contact It cannot be lifted, check the water level sensor.

L5 LU Low Voltage Protection Automatically resumes operation when the grid voltage rises.

Hu High Voltage Protection Cut off the power supply immediately, check the power supply voltage.

ff Unknown Fault Unplug the power plug for fault check and repair.

Have a great day

The e2 washing machine should be caused by the upper cover not being covered properly, and the e2 washing machine is not dehydrated within four minutes.

The automatic washing machine displays E2: refers to the draining timeout (if the water is drained for more than 6 minutes, the alarm can be lifted by opening and closing the door cover once). Troubleshooting:

1. Check to make sure that the drain pipe has been lowered.

2. Check whether the drainage pipe is deformed or twisted.

3. Check whether the drain pipe is unblocked and whether there are any foreign objects blocking the drain pipe.

4. The above three points are common reasons for the washing machine not draining or draining slowly, if the washing machine does not drain due to these faults, it can be easily eliminated.

Tips for choosing a washing machine:

1. Select according to the cleanliness degree and wear rate.

The drum washing machine simulates hand rubbing, with uniform cleanliness, low wear rate, and clothes that are not easy to wrap; The cleanliness of the washing machine is 10% higher than that of the drum washing machine, and naturally its wear rate is also 10% higher than that of the drum washing machine.

In terms of cleanliness, the washing ratio of the washing machine and the drum washing machine is greater, the wear rate of the wave wheel washing machine is less than that, and the drum washing machine is less than that.

2. Select according to power consumption and water consumption.

The washing power of the drum washing machine is generally about 200 watts, and if the water temperature is increased to 60 degrees Celsius, it will generally take more than l00 minutes to wash clothes once, and the power consumption is about one degree. In comparison, the power of a washing machine is generally around 400 watts, and it only takes up to 40 minutes to wash clothes once. In terms of water consumption, front-loading washing machines are about 40% to 50% of those of wave wheel washing machines.

An E2 failure in the washing machine refers to a drain timeout, and in general, it will be dehydrated for more than six minutes after E2** and an alarm signal will appear. If there is an E2 fault, the alarm can be lifted by opening and closing the door cover once.

My washing machine is Midea, the fault of E2 is the drainage timeout, E3 is the door cover is not closed tightly, E4 is the dehydration correction, E1 is the water inlet timeout.

With the continuous development of science and technology, many families have now added washing machines, and there may be E2 failures in the process of using washing machines, so what is E2 failure? Let's take a look.

Washing machine E2 malfunction

E2 failure in the washing machine** refers to the state lead drain timeout, generally speaking, the lead drain for more than six minutes will cause an e2** failure and an alarm signal will appear. If there is an E2 alarm, the alarm can be lifted by opening and closing the door cover once.

Causes of E2 failures

There are many reasons for E2 failure, such as: 1. The drainage pipe is not put down, resulting in water that cannot be removed; 2. The drainage pipe is deformed or twisted, resulting in too long drainage time; 3. The drain valve is blocked, resulting in the water being unable to be discharged; 4. There is a problem with the circuit, etc.

In general, an E2 failure in a washing machine** refers to a drain timeout, and in general, an E2** will occur and an alarm signal will appear after draining water for more than six minutes. Do you understand?

The automatic washing machine displays E2: refers to the draining timeout (if the water is drained for more than 6 minutes, the alarm can be lifted by opening and closing the door cover once). Hall laughs blind).

Washing machine empty E2 troubleshooting method:

1. Check to make sure that the drain pipe has been lowered.

2. Check whether the drainage pipe is deformed or twisted.

3. Check whether the drain pipe is unblocked and whether there are any foreign objects blocking the drain pipe.

Washing machine can not be dehydrated troubleshooting:

1.The laundry is in an unbalanced state when washing. Elimination method: You can put a small amount of clothes before washing clothes, and don't stuff too much at once, so as not to cause imbalance during washing. And the effect of dehydration is not good.

2.The safety switch on the top cover of the washing machine is damaged. Try not to open the top cover during the dehydration process to avoid damage to the top linkage switch.

3.The washing machine drain system is clogged. Elimination method: Remove the drain filter to clean the stream, flush the drain with water and remove the debris in the drain valve.

4.The water level switch cannot be reset. Solution: Contact the after-sales point.

5.Due to a faulty motor, the washing machine cannot be dehydrated. Exclusion Method:

You can try opening the back cover of the washing machine and moving the pulley by hand if there is no jamming. After the power is turned on, the motor does not rotate with a humming sound, which means that the motor is short-circuited or damaged between turns, or the capacitor is not connected to the motor circuit. At this time, the power supply should be cut off, and the motor belt should be removed and restarted.

If the motor still does not rotate or the speed is low, it is a motor failure and the motor should be repaired or replaced.

The reason for the failure of the washing machine to show the E2: the cover on the washing machine is not closed during operation or the reed switch in the control panel holder is broken.

Solution: 1. Open the lid when the washing machine is running, and the machine will report E2 to prompt the user to close the lid.

2. If the E2 alarm still appears after closing the lid and restarting, check that there is a small magnet on the right side of the transparent cover to control the reed switch in the tray base to see if the small magnet has fallen off or the reed switch is broken.

3. If the above inspection cannot be solved, you can consult professional after-sales personnel.

Answer 1: The safety switch of the top cover of the washing machine is damaged, and the washing machine is a high-speed mechanical movement in the process of dehydration. Try not to open the top cover during the dehydration process to avoid damage to the top linkage switch, if the top cover linkage switch of the washing machine is damaged, the washing machine can not be dehydrated.

2. The washing is in an unbalanced state when washing, and the washing cannot be adjusted to balance when there are too many clothes, then the washing machine will automatically adjust to a low speed to cause poor dehydration effect.

3. The water level switch cannot be reset, and the dehydration procedure of the washing machine starts under the condition that the water level switch is reset after the washing liquid is discharged. If the drain level switch is damaged, dewatering is a procedure that needs to be carried out after draining, and if the water level switch is damaged, you will not be able to enter the dewatering program!

4. The texture of the clothes is caused by the fact that compared with summer, there are many types of clothes in winter, such as the tweed type of clothes with strong water absorption, if you choose low-speed dehydration, it will cause the illusion that the washing machine cannot be dehydrated.

Question: Try washing many times, but the dehydration function cannot be used normally.

Answer: The washing machine shows e2, which means that the lid of the washing machine is not properly covered, the user can check whether the lid of the washing machine is stuck by a foreign object, if there is no foreign object, then lift the lid and close it again and try to run again.

Summary. Hello, the appearance of E2 is generally the cover of the washing machine is not covered, in this case it may be thought that there is a foreign object, affecting the normal closure of the cover, will display such a sign, prompting to clear the obstacle, close the lid of the washing machine.

Hello, is it a fully automatic washing machine?

Hello, the appearance of E2 is generally the lid of the washing machine is not covered, in this case it may be thought that there is a foreign body, affecting the normal closure of the lid next to the silver closure, will display such signs, prompting the removal of obstacles, early start to close the lid of the washing machine.

The second situation may be that the drainage is overtimed, check whether the drainage pipe has a deformation or blockage, if there is a problem of deformation and blockage, then we need to dredge the Xunxun drainage pipe as soon as possible.

Let's see what kind of situation you belong to.

Hello, I am honored to answer this question for you, the automatic washing machine shows that E2 refers to the draining timeout (draining for more than 6 minutes), and the alarm can be lifted by opening and closing the door cover once. Washing machine E2 troubleshooting method:

1. Check to make sure that the drain pipe has been lowered.

2. Check whether the drainage pipe is deformed or twisted.

What is the fault of the washing machine with E2?

Hello, I am honored to answer this question for you, the automatic washing machine shows that E2 refers to the draining timeout (draining for more than 6 minutes), and the alarm can be lifted by opening and closing the door cover once. Washing machine E2 troubleshooting method:

1. Check to make sure that the drain pipe has been lowered.

2. Check whether the drainage pipe is deformed or twisted.

Without the above problems, it is still not easy to use.

Drain supermarket. Timeout: It's a system failure, how do you know no.

This happens without washing.

That's how it starts.

Now I have clothes in the washing machine.

The washing machine has a lead starvation E2 failure** refers to a drain timeout. The washing machine drains out of time. Under normal circumstances, if the washing machine drains more than six minutes, this fault alarm will occur.

For this fault phenomenon, the alarm can be removed by opening and closing the lid of the washing machine once. But it still can't be solved, you need to check whether the drain pipe is stuffy or deformed, and if so, it needs to be put down or replaced.