How to seal the heating stove

Seal the heating stove as follows:

1.Heat the entire heating system, and the return water temperature needs to reach 40-50 degrees;

2.The coal seam and coal block in the furnace must be red and not scattered, and the fire will be laminated into a flat surface at this time

3.Take some uniform small coal pieces and put them on the plane of the fire layer, and then gently compact;

4.Take a slightly larger coal block and put it into the furnace, and finally put a little crushed piece into the top to compact;

5.Cover the fire lid and open one-third, open one-third of the side air inlet, and close the hopper drawer.

Precautions should be taken when using the heating stove

First, after the purchase of household heating stoves, the manufacturer will come with a manual, the user can not blindly operate after getting the manual, should be familiar with the operating procedures of the heating stove.

Second, if the weather warms, generally if there is no need for geothermal system heating, it should be noted that there should be a process when shutting down the geothermal system, the cooling process of the floor should be gradual, not suddenly, if the cooling speed is too fast, it will also affect the service life of the floor.

3. Try to avoid using legless furniture for furniture using heating stoves, otherwise it may lead to local deformation of furniture due to overheating.

Fourth, if you use a geothermal heating stove for the first time, you must pay attention to the indoor heating should be slowly heated and gradually, otherwise the floor will crack and twist due to the expansion of Director Guo, and it should also be noted that the inlet water temperature of the floor heating system should not exceed 60 degrees Celsius.

Also, the temperature of the water supply return should be less than or equal to 10 degrees Celsius.

When sealing, do not burn too vigorously when sealing the furnace, it is advisable to burn the lump of coal inside and not scatter it, fill the lump of coal and the inner furnace mouth flush and cover the outermost furnace cover, and leave a small gap of 2 to 5 mm when the lid is aimed at the flue. The lower seal should be left with a small slit of 1 to 3 mm. No problem.

You must first know whether your heating stove burns coal or briquettes, my house burns coal, and it goes off every day at the beginning, but I don't seal it these days, because it's cold, and I get up in the middle of the night to store coal.

Hello: The use of natural gas heating stoves is as follows: 1. This gas wall-hung boiler should be ventilated with water first, and then connected to the plug.

After all, the gas should be ignited and energized. 2. Turn on the faucet first, and the wall-hung boiler will be filled with water. 3. Then click the switch to automatically ignite and heat up.

4. After that, the hot water will be slowly transported to the pipe, the indoor temperature will gradually rise, if you don't use it, you can turn off the switch, this wall-mounted heating furnace is very convenient, and the heat rises quickly

1. There must be a sufficient primer, if, at night, we want to seal the stove, then, we must add enough carbon first, so that the furnace is prosperous.

2. Let the furnace have enough space to add new carbon, add new carbon to the very strong primer, and fill the furnace.

3. To close the furnace, close the furnace door first, pay attention to the time when closing, do not close tightly, there must be a slightly thicker gap, so that the carbon in the furnace can continue to burn, but not excessive, nor extinguished.

When sealing the furnace, you should pay attention not only to save carbon, it is not as expensive as saving, and you have to be reborn if you put out the fire once, and you need a furnace hole for carbon. When sealing the fire for the first time, it is best to choose new coal with a relatively uniform size for sealing the fire, and it is best to check the state of the sealing fire, if the flame is not suppressed, it is easy to extinguish all the coal after consumption.

You close the lid on the inside, then the lid on the outside, and finally open the small door on the front so that there is no waste or extinguishing the fire.

1. If the closure is not strict, the empty and coarse filial piety will enter, and check the upper and lower seals of the boiler and the furnace stool, and whether there is a gap after the closure;

2. Carefully check the bottom of the stove to see if there is a large piece of ash on the stove, and stop the fire to clean it up if necessary;

3. If it is air leakage caused by the aging of the furnace, replace the boiler in time;

4. Consider whether the boiler selection is correctly proportioned with the radiator or the heating area of the mining ruler.

Before sealing the furnace, the first thing to do is to fill the furnace with carbon, there can be no gaps, so that the furnace is prosperous, when closing the furnace door, do not close it tightly, there must be a slightly thicker gap, so that the carbon in the furnace can continue to burn, but not excessively, and not extinguished.

When the furnace burns, it absorbs oxygen and releases toxic carbon monoxide, so never use the stove in a confined space, and do not use a gas tank that will leak, and leave it in a ventilated place to deflate. Chain Jane.

Do not store the fuel together in the furnace, especially the liquid fuel, in case of leakage it is dangerous, and the place where the furnace is stored is best kept dry to avoid rust and corrosion of the metal.

When using the stove, try not to let the soup leak out and get on the stove, in case of leakage, wait for the stove shed with pants to cool down after the stove is used before cleaning to avoid the stove nozzle blockage.