How do I replace my water and electricity? It has been renovated.

Updated on home 2024-07-13
37 answers
  1. Anonymous users2024-02-12

    If you say that the inside of your home has been renovated, but now you want to change the water and electricity, Weibo is like you said, to knock out all the bathrooms and reinstall them, you only need to knock on the place where you need to go through the pipes again.

  2. Anonymous users2024-02-11

    Replace the water and electricity in your home, if it has already been renovated. Then you can choose to smash it all and renovate it, and the water and electricity lines can be pressed into the wall and buried. If it's surface-mounted, it's also possible.

  3. Anonymous users2024-02-10

    When a new house is converted to water and electricity, the waterway must be renovated first. When renovating the waterway, it is necessary to first play the line on the wall and dig it, and then install the cold and hot water pipes. After the installation is completed, the entire waterway pipeline should be inspected to see if there is one.

    Then you can carry out circuit transformation, and when the circuit is transformed, it is necessary to dig and wiring, so that the wiring in the whole house will be more beautiful.

  4. Anonymous users2024-02-09

    If your home has been renovated, if you want to replace the water and electricity, I think it is more troublesome, the electricity is a little better, you can pass the line through the pipe. But the water can only be opened.

  5. Anonymous users2024-02-08

    1. Design the direction of water and electricity according to the design drawing of the room and the specific needs of customers. 2. Workers press away. Avoid temporary replacement of water heater types, resulting in repeated renovation of the waterway.

  6. Anonymous users2024-02-07

    If you don't have all the markers, knock off the obstructions, and replace the threads, you can ask to see it

  7. Anonymous users2024-02-06

    It is possible to disassemble the damaged wall and partially reassemble the circuit.

  8. Anonymous users2024-02-05

    Hello, I have paid social security for a year, and I can't find the balance, there is a possibility that I bought social security, which is the type without a personal account. You can check the payment details.

  9. Anonymous users2024-02-04

    The water and electricity are in the wall, which is a hidden project, and it is very troublesome to transform it in the later stage. Therefore, if you want to not be bothered by these trivial things after moving in, you must determine the base according to your own living habits during the design stage.

  10. Anonymous users2024-02-03

    Don't move too much. Focus on the bathroom, kitchen. As long as the water pipe is a PPR pipe, it should be fine.

    See if the wire of the kitchen socket is 4 square copper wire, it is recommended to replace it. The sockets in the bathroom should also reach 4 square meters. There is no need to replace the living room and bedroom, because this uses the least electricity.

  11. Anonymous users2024-02-02

    Then adjust it according to your personal decoration style and design ideas.

  12. Anonymous users2024-02-01

    The old ones should be replaced, and the new ones should be replaced.

  13. Anonymous users2024-01-31

    Changing water and electricity is a major item in decoration, and it is also the most important one, as the saying goes: "e68a8462616964757a686964616f31333431343635 water and fire are merciless", so we must pay attention to several key points of changing water and electricity when decorating the house:

    Precautions for water improvement:

    1. PPR water pipes must be selected from big brands, materials can not cost a few more money, cold water pipes should not be used for hot water, once leakage is a big deal;

    2. The water improvement master must find someone with more experience and meticulous work (you can see that there is construction), and don't look for a half-pull to change the water, which can't save a few dollars;

    3. It must be noted that when the pipeline is cut, the cross-section of the pipeline must be flat, and there can be no angle and stubble, because the interface of the pipe fitting is very short, and the pointed place will contact the pipe fitting first, and the other positions and pipe fittings will be connected virtually, and it will be easy to leak after a few days of high pressure; Secondly, the pipe fitting thread link should be wound with the raw material belt;

    4. Brand PPR manufacturers have free suppression, and the pipeline must be suppressed and tested after the completion of welding.

    Precautions for changing power:

    1. The plastic copper wire must use the national standard wire, do not look at the outer diameter of the wire, look at the diameter of the copper core inside; Generally, 6 or 10 flame retardant plastic copper wires are used for external wire incoming (according to the power consumption);

    2. Socket: 4 wires, three fire grounds, soldering treatment at the joint, waterproof insulating tape wrapped, PVC pipe must be set, and it is best not to have joints on the ground and on the shed;

    3. Lamp wire: plastic copper wire;

    The above is the most important part of changing water and electricity, as for whether the wall slotting is straight or not, this is not very important;

    By the way, in addition to changing water and electricity, whether it is simple or finely decorated, its effect is in the living room, and a beautiful TV background wall can multiply the decoration effect several times;

    According to the above points, your decoration is safe, classy, and saves money;

  14. Anonymous users2024-01-30

    First of all, you need to have a rough idea of what future appliances are in your home and where to put them. Then install the wire box according to the need, and take the power. The same goes for water, which is more and more dense depending on your design.

    Then the water is channeled. It is recommended to leave a few more wire boxes (referring to sockets) when making electricity!

  15. Anonymous users2024-01-29

    Change the water, and finally call in professionals; Change the power and put as many outlets as possible.

  16. Anonymous users2024-01-28

    According to your own needs, and then the designer designs it like this.

  17. Anonymous users2024-01-27

    It varies from person to person, the pattern of the house is different, it is best to find a professional team to change, so that you can look at the drawings, and you should keep the drawings after the electrical transformation, which has been used in the future when you are at a loss.

  18. Anonymous users2024-01-26

    According to your own preferences, adjust the position of the original design plumbing and electricity to facilitate your own use.

  19. Anonymous users2024-01-25

    First of all, you have to plan where to put those electrical appliances, and then you have to install and modify the water and electricity master according to your plan to change the water and electricity.

  20. Anonymous users2024-01-24

    It depends on how you want to change it, and then look for the design.

  21. Anonymous users2024-01-23

    Hire professionals to modify according to each person's needs.

  22. Anonymous users2024-01-22

    After determining the furniture arrangement, the water and electricity renovation plan is determined.

  23. Anonymous users2024-01-21

    Hydropower renovation is a more important thing in the decoration, but also more individual, the requirements of each family are different, mainly according to the needs of the owner, some need to take the bright line, some need to go to the wall groove to go dark line, this depends on the needs of the owner.

  24. Anonymous users2024-01-20

    1. Waterway part.

    1. The design of the waterway should first think about all the equipment related to water, such as: water heaters, water purifiers, kitchen treasures, water softeners, washing machines, toilets and wash basins, etc., their location, installation methods and whether hot water is needed;

    2. Think about whether to use gas or electricity water heaters in advance, and avoid temporary replacement of water heater types, resulting in repeated transformation of waterways;

    3. In addition to leaving the water outlet for the wash basin, dun cloth pool, toilet, washing machine, etc., it is best to take one out, and it is very convenient to receive water and flush the ground in the future;

    4. After the location of the washing machine is determined, the drainage pipe of the washing machine can be considered to be made inside the wall, which is beautiful and convenient;

    5. There should be a pressure test after the waterway is reconstructed.

    Second, the circuit part.

    1. The design of the circuit must be determined after considering the possibility, feasibility and availability in detail. No one wants to have wires all over the walls and floors of their new home. At the same time, the circuit design should also pay attention to its flexibility, and consider connecting a plug-in board in the future in the position where the electrical plug is more concentrated, and the effect is often better than setting up a socket with a full wall;

    2. Dual control of the ceiling light in the bedroom (bedside and door);

    3. The ceiling light in the living room can be considered to be installed with a sub-control switch according to the needs of life (entering the hall and returning to the door of the master bedroom);

    4. The socket is generally 30cm from the ground, and should not be less than 20cm, if the living room uses a low cabinet as a TV cabinet, it can be higher from the ground, so as not to block the socket from the TV cabinet, not only against the wall. The switch is generally 130cm from the ground;

    5. The exhaust fan switch and socket should be installed near the toilet, not by the wall of the bathroom door;

    6. The bath bomb should be installed close to the shower room or bathtub, rather than in the center of the bathroom; Balconies, corridors, and cloakrooms can consider reserving sockets;

    7. For spaces with mirrors and coat hooks, consider the lighting near the mirror;

    8. The living room, master bedroom and bathroom should be preset according to personal living habits and convenience;

    9. There are up to three lines in a pipe, and remember: before the transformation, it is necessary to explain how 1 meter is calculated, and it should be calculated according to one pipe, not one line;

    10. The location of the socket is very important, and there are often sockets that are located right behind the bedside table, resulting in the situation that the cabinet cannot be against the wall.

    11. Some kitchen sockets are still convenient with switches to avoid the inconvenience of pulling out the plug of the rice cooker from time to time in the future.

    12. There is no need to set up too many sockets behind the TV, and it is best to put a plug-in board on the side of the TV in the future.

  25. Anonymous users2024-01-19

    Go to the side of the road and find a renovation worker to ask first, understand the cost is the most important.

  26. Anonymous users2024-01-18

    If there is a problem in the later stage of hydropower decoration, it can be replaced and remedied in time. It is necessary to pay attention to the selection of high-quality materials and skilled workers to decorate water and electricity, and avoid mistakes as much as possible.

  27. Anonymous users2024-01-17

    If you want to repair the water and electricity decoration, all the waterways should go to the top, and the part that needs to be buried in the wall should be used with the whole pipe, and the pressure test will be completed after the construction is completed, so that even if you want to repair, you don't need to smash the wall and knock the ground.

  28. Anonymous users2024-01-16

    It is best to use the materials used in the decoration of water and electricity, so that the life is longer, and try to reserve a part of the space between the water and electricity during the decoration, so that the maintenance will not hurt other water and electricity in the future.

  29. Anonymous users2024-01-15

    Don't move too much. Focus on the bathroom, kitchen. As long as the water pipe is a PPR pipe, it should be fine. Look at the wires of the kitchen outlet.

    It is recommended to replace the copper wire of 4 square meters. The sockets in the bathroom should also reach 4 square meters. There is no need to replace the living room and bedroom, because this uses the least electricity.

  30. Anonymous users2024-01-14

    If you think that the developer's materials are not good, there is no need to dig up the wiring when reinstalling, and the slotted wiring will be fine, as long as the shear wall is not used will not affect the house.

  31. Anonymous users2024-01-13

    There is no need to replace or change the original water circuit, which will increase your costs, and if you want to replace it all, there is no need to dig it up, just replace the wires inside, and the water pipe can be re-slotted.

  32. Anonymous users2024-01-12

    You have to dig and knock it, and as long as the house doesn't get a load-bearing structure, it's generally fine.

  33. Anonymous users2024-01-11

    There is still a lot of work to be done.

    The renovation of water and electricity in decoration is mainly based on the transformation of the water and electricity lines installed by the developer. If the original pipeline is in the way, it will be dismantled; If you don't get in the way, you can not dismantle it, after all, the demolition work is labor-intensive, and the current labor can't afford to delay.

  34. Anonymous users2024-01-10

    Just check it, and if you don't change it, you don't have to move it.

  35. Anonymous users2024-01-09

    If you are a first-time homeowner, you must remember that the installation of water and electricity is the most important thing in decorating your house. Plumbing and water installations are covert and are buried inside walls or under tiles. You can't change it at any time.

    So I will say a few points of precautions for hydropower installation: first of all, circuit engineering, all electrical control lines and lines must wear PVC pipes. If there is no shady corner at the ceiling and there is a force reduction wall, the line will go from the wall.

    The same circuit wire should be laid in the same pipe, the wire diameter is appropriate, and the number of pipes should be so that the cross-sectional area of the pipeline is not more than 40% of the cross-sectional area of the PVC pipe. The bending degree of the wire shall not be greater than 90 degrees, and when it exceeds 90 degrees, it shall be connected with pipe fittings. When the wire is threaded, the strength must be separated, and all the wires must be threaded.

    The joints are firm and reliable, and the insulation performance is good (the resistance value is greater than. The layout of the line is reasonable. The fixed position of the switch and socket must meet the requirements, that is, the switch is 1200-1300mm from the ground, and the socket is 300-450mm from the ground.

    The direction of each line is clear and orderly. If the indoor area is more than 40 square meters, the air conditioning line should be laid with 4 square millimeters BV copper core wire. This is followed by waterway engineering

    All fittings are strong, reliable and have a good seal. The outlet of the open water pipe should be cold at the top and hot at the bottom, hot on the left and cold on the right. Concealed indoor pipes must be pressurized before they can be sealed.

    Generally, under the premise that the working pressure is not greater, no decompression phenomenon is qualified. In the waterproofing process, the overall cast-in-place waterproofing generally requires one cloth and three oils, or two cloths and six oils (cross paving). The waterproof layer of the coating must be smooth, uniform, and free of defects such as peeling, shelling, cracks, and bubbling.

    The inspection method of waterproof engineering is: water is turned off for 24 hours without leakage, that is, it is qualified. Finally, the materials for the installation of water and electricity also need to be very strong.

  36. Anonymous users2024-01-08

    Upstairs said that it was wrong, and now it is no longer necessary.

    Align the line from horizontal and vertical against the wall.

    bai du, this is called winding, national zhi

    Home has long been banned. Dao** will be many times higher, should be slotted buried at the shortest distance, the socket switch can be connected with the adjacent socket switch, can only be connected at the socket switch, so that it is convenient to overhaul, the wire socket switch light with 2.5 flat wire, air conditioning more than four flat, oven more than six flat, different types of wires can not be jointed, to add air conditioning port or oven must go a separate line, network cable can not be connected, no matter how many network cable ports are installed in the room must take a line separately from the weak current box.

  37. Anonymous users2024-01-07

    Hydropower renovation refers to the renovation process of replacing all or part of the waterways and circuits used by the original developer according to the decoration configuration, family population, living habits and aesthetic concepts. Hydropower transformation is divided into waterway transformation and circuit transformation. Hydropower projects are hidden projects, so they must not be sloppy!

    It is recommended to choose a regular large-scale home improvement company!

Related questions
8 answers2024-07-13

All kinds of impurities in the pipeline should be completely removed during installation. Spool damage, jamming, clogging and leakage are prevented. At the same time, the surface should be cleaned so that no residue of building materials remains. >>>More

8 answers2024-07-13

Its walls are harder than the new houses, and it is very troublesome in terms of grooving and grooving, and it is necessary to demolish the old ones, and change the water and drainage, and some old houses are not allowed to destroy the floor tiles, which is also troublesome, so it will definitely be high.

7 answers2024-07-13

Generally speaking, it is done in a horizontal and vertical or two-point and one-line manner, and a lock needs to be added between the wire pipe and the wire box. In addition, the distance between strong and weak electricity must be controlled at more than 50 centimeters to avoid interference. For water pipes, cold water pipes and hot water pipes should not be located in the same trench, and the distance between them should be controlled to 10 to 15 cm. >>>More

6 answers2024-07-13

I want to install a mirror for my own room, a long dressing mirror, because the frame is not good, so I want to glue the mirror directly to the wall, and then paste the glass mosaic on the side as a frame, I don't know if this is feasible, my home has been renovated, can it be processed directly like this? The mirror is so glued, can it be glued? The last time I looked at the swap space, I saw that I could directly coat the mosaic with something like latex or what kind of glue, and then it could be glued directly to the wall, how did I get it? >>>More

22 answers2024-07-13

Everyone is full of expectations when decorating their new home, hoping to decorate it beautifully and warmly, because it will be a small family to live in for a long time in the future, so they will also pay extra attention to the decoration process. However, in the past, there may be a problem, that is, when renovating water and electricity, various pipes will be installed directly on the wall or floor. >>>More