What to do if the sealing strip of the refrigerator sliding door fails

You can apply a hot towel or spray it with the steam of a steam iron, which is estimated to soften and regain elasticity.

Remove it, soak it in hot water, then install it, and then use a hair dryer, hot air, blow it down, and you can only do it if you don't want to change it.

Soak in hot water and replace the sealing strip.

If the hot water soaking refrigerator seal is deformed, then I can remove it, and then put the deformed part into the prepared hot water to soak, soak for about 10 minutes or soak out, and at the same time place it on a flat countertop, gently straighten it. You can also use a hair dryer to blow hot air to blow up the bad seal of the refrigerator door, and it will be good after cooling. The hair dryer should not blow for too long, the distance should not be too close, and the temperature should not be too high.

Eliminate iron filingsIf you find that there are some iron filings or metal powder stuck on the refrigerator sealing strip, then it will also cause the refrigerator door to be closed loosely, at this time, just use a brush or rag to remove the iron filings. Replace the sealIf the refrigerator seal is seriously aged, it needs to be replaced with a new one, otherwise it can no longer be used. You can replace it yourself or report for repair, so that professionals can deal with it to avoid more serious damage.

If the refrigerator does not have a sealing strip, then the refrigerator door will not close tightly, which will seriously cause the refrigerator to waste electricity, and if the refrigerator does not have a sealing strip, the refrigerator will not work normally. Therefore, it can be seen that the refrigerator seal has brought great convenience and plays a very important role in life.

Refrigerator door closed not tightly Solution:

1. Hair dryer setting method. In the place where the seal is not good, take the hair dryer to blow the place with hot air, the noisy high wind time should not be too long, the plastic door seal can be soft, and the door seal will be deformed and repaired after stopping the blowing for about two minutes. If the refrigerator door seal is bent in an S-shape, you can use a ruler to pad the inside of the seal, and then use a hair dryer to heat the bent part slightly, until the plastic is slightly bent and soft, then stop heating, and after the refrigerator door seal is cooled, then pull out the ruler, which can restore the seal to the original shape before lifting.

It must be noted that when using hair dryer heating, generally use about 700 watts of hair dryer, control within one minute, and the air outlet should be 3 cm away from the seal.

2.Hot water immersion setting method. You can remove the refrigerator door, cut the adhesive parts of the 4 corners of the door seal with a knife, and remove the magnetic strip.

Remove the door seal, as long as the deformed door seal is soaked in hot water at about 60 degrees Celsius, turn it from time to time, remove it after 7-8 minutes, and gently straighten it with your hands on a flat countertop. Once cooled, the curved door seal will be flat and straight. If the thickness of the door seal is inconsistent, the thicker part should be pulled several times.

After the door seal is straight, the length has been increased due to the reason of stretching, and the excess part should be cut off when installed on the refrigerator door, and the end should be beveled at a 45-degree angle. When installing a magnetic strip into the door seal, the side with the high suction should be facing the box and glued with 502 glue. The 4 corners can be heated with a hacksaw blade and inserted into the corner seams, and the hacksaw blades are pulled out after the door seal seams are melted, and then loosened after pinching for a while, and the door seals will be glued firmly.

3.Repair the door seal method with white rubber. If the door seal is slightly deformed, and the plane is not straight, the screws that fix the door seal can be loosened, and the white rubber is padded in the plane where there is a gap, and then the screws are re-tightened to eliminate the gap.

If the door is not parallel to the box after closing, the bracket that holds the door can be adjusted so that it is parallel to the two. You can also stuff some soft plastic foam into the gap of the door seal to solve the problem of the door seal is not tight.

4.Except for the refrigerator door seal iron filings method. Iron filings or metal powder are adsorbed on the magnetic door seal, which makes the door not close tightly.

The solution to the unsealed seal on the refrigerator door is to replace the seal.

If the refrigerator seal itself is not sealed due to aging, you can only choose to replace the refrigerator seal with a new one. Then it can be used normally. Poor sealing of refrigerator doors will affect the stability of indoor airflow and temperature, making the refrigerator need more power to maintain a constant temperature.

This not only wastes a lot of electricity, but also increases the electricity expenditure of the family.

Secondly, users should also know that if the refrigerator door is not tightly sealed, it will lead to unstable indoor temperature, and the perishable foods such as vegetables and fruits that we put in the refrigerator are easy to mold and deteriorate, and perishable foods such as meat and seafood will also lose their freshness due to insufficient temperature. Therefore, the question of whether the refrigerator door seal is in place is still very important.

Precautions for refrigerator sealing

A well-sealed refrigerator prevents cold air from escaping and keeps the temperature within the proper range, so the freshness and shelf life of the food can be guaranteed. Secondly, a well-sealed refrigerator can effectively prevent external odors from contaminating the food and ensure the original taste and hygiene of the food. A well-sealed refrigerator can effectively reduce the waste of energy, as the refrigerator no longer needs to be cooled frequently.

Many people use refrigerators close to the cracked surface of the wall, which is obviously incorrect. Because the wall will absorb the heat emitted by the refrigerator, the temperature at the back of the refrigerator will rise, and the cooling effect will be lost. Moreover, clinging to the wall will also make it more difficult to open and close the refrigerator door, which can easily cause the refrigerator sealing strip to deform and affect the sealing.

The seal on the refrigerator door does not seal the solution:

1. Soak in hot water.

The common reason why the refrigerator seal is not sealed is that it is deformed, and as long as the shape of the refrigerator seal can be restored, it can be restored to normal functional use.

2. Blowing and shaping.

Using the hot air of a hair dryer, blow the deformed part of the refrigerator seal, reshape it, and then it can be used normally.

3. Eliminate iron filings.

The refrigerator seal will be stained with some iron filings or dirt when used for a long time, which will cause a gap between the refrigerator and the seal, resulting in a loose seal, just remove these things.

4. Replace the sealing strip.

If the refrigerator seal itself is not sealed due to aging, you can only choose to replace the refrigerator seal with a new one.

If the seal on the refrigerator door is dropped, there are several solutions to consider:

1.Reinstallation: Check that the seal is intact and if it is only loose, it can be reattached to the refrigerator door. Follow the refrigerator manufacturer's instructions or the manual to find the correct installation location and make sure the seal fits perfectly and seals tightly.

2.Replace the seal: If the seal is damaged or cannot be reinstalled, a new seal will need to be replaced. You can contact the refrigerator manufacturer or repair center to ask if there is an original seal suitable for your refrigerator model, and buy a new one for replacement.

3.Temporary Repair: If a new seal cannot be replaced immediately, a temporary method can be used to repair it.

For example, use tape or silicone sealant to temporarily attach the seal to the refrigerator door to maintain a certain seal. However, this method is only a temporary solution, and it is best to replace the seal with a new one as soon as possible.

Either way, make sure that the seal on the refrigerator door fits perfectly and maintains a good seal, which can help keep the temperature inside the refrigerator stable, save energy and prevent cold air leaks. If necessary, it is recommended to consult a professional technician or contact the refrigerator manufacturer for more detailed guidance.

1) Re-foaming maintenance method? When overhauling, it is necessary to pry open the back panel of the refrigerator and dig out the original foaming material (you should be very careful not to damage the original pipes and wires when digging). After exposing the evaporation pipe, it is then filled with nitrogen to detect leaks, and special attention should be paid to each connecting solder joint during leak detection.

This repair method is more suitable for the refrigeration system with a connector on the back, and is not suitable for internal leakage in the refrigeration pipe with leakage points at deeper levels. After the leakage point is detected, repair welding or repair it with an adhesive pool, and then re-foam and repair the backplate. (2) Acoustic leak detection method?

First, fill all the refrigeration pipes with nitrogen. Then use a stethoscope to inspect all parts of the interior and make a mark when you hear an air leak in a certain area. Carefully pry open the metal plate at the place, check the leakage point of the scattered pulse pipe with thick soapy water, repair it by repair welding or adhesive method, then fill it with foaming agent, use a larger metal plate to repair the pry mouth, and glue it firmly on all sides.

This method is powerless for the micro-leakage of the refrigeration system, which is easy to cause false detection or missed detection. (3) Evaporator replacement method? After the leakage of the evaporator is determined, the finished evaporator that can fit into the inner cavity of the original evaporator is replaced and repaired.

Connect the new evaporator to the original refrigeration piping and replace it with a new capillary and dryer. The disadvantages of this method are that it is costly, and it is powerless when encountering evaporators with special shapes or multi-door refrigerators, as well as leaks in the refrigeration pipes of freezers. (4) Copper tube coiling method?

This is a suitable repair method for any type of refrigerator that leaks. When maintaining the plan, it is generally calculated that the size of the purchased copper pipe is calculated first, and the shape and length of the coiled copper pipe are determined according to the size of the refrigerator liner. Taking a double-door direct-cooling refrigerator as an example, the freezer generally only needs to be on the left, top and right sides of the plate, and the refrigerator only needs to be coiled around a small piece close to the box board, and the freezer can be coiled by the wrap-around method.

The coiled new evaporator is then fixed to the metal sheet wall with a fixing card and self-tapping screws.

The seals of your refrigerator are all magnetic. It is used to adsorb on the refrigerator to enhance the sealing of the door. Now that the seal has fallen, it means that his magnetism is gone. So all you have to do is re-magnetize. Or the person who respects the person directly annihilates the book of Volgents and carries a new seal.

After the sealing strip of the refrigerator is broken, the refrigerator door cannot be closed tightly, which will affect the refrigeration preservation effect of the refrigerator.

Reasons and solutions for the refrigerator door to be closed loosely:

First, the door seal is aging, because the refrigerator door is opened and closed very many times, which makes the refrigerator door seal almost often under the stress state, and if it is in such a state for a long time, the door seal is easy to appear aging cherry belt burning, deformation, etc., so that the refrigerator door will not be closed tightly;

Second, the suction power of the refrigerator door is not large enough, and most of the refrigerators on the market now use drawer design, which solves the problem of opening and closing the door for children, but once this technology is not too hard, it is easy to cause the refrigerator door to loosen, so that the refrigerator door is difficult to close tightly;

Third, the refrigerator is not properly maintained, in fact, the refrigerator is the same as us, it must be maintained properly and often, and if it is not properly maintained for a while, or it has never been maintained, it will make it sick and accompany, and the refrigerator door is not closed tightly;

Fourth, it is very important to clean the refrigerator correctly, for the treatment of the refrigerator, not only the inside of the refrigerator, but also the outside of the refrigerator should be cleaned frequently, otherwise once too many stains are deposited on the outside of the refrigerator, the refrigerator will not be closed tightly, and the door seal should be cleaned regularly and correctly.