Haier automatic washing machine dehydration touches the cylinder

Dehydration hits the cylinder, generally there are the following two situations:

The laundry inside the spun bucket is not evenly arranged.

Most commonly found in sleeve washing machines, sleeve washing machines for the winding of clothes, there is currently no good solution. Therefore, in this case, it is best to pause the machine and unwind it manually. Then start the dehydration procedure.

If there is no artificial interference, the washing machine shakes the protection switch, and the water will enter to perform the washing action, trying to place the clothes evenly, after 3 times, the alarm will be suspended.

If there is a problem with the shock spring, even if the spring on one side is not adjusted well, the machine will not be able to balance the work, resulting in the inability to weaken the vibration and hit the cylinder. It is a bit difficult to adjust it yourself, but it is recommended to deal with it by after-sales, after all, if there is damage, there will be after-sales accessories to replace.

The shock absorber is generally visible when the top cover is opened, please see the picture:

Hello, thank you for asking the company.

Dear, at the end of the fully automatic dehydration, there is a braking process, and this process sometimes has this kind of "hitting the barrel" sound that you say, which is normal; If it is more severe, it can be caused by the following reasons:

1: The washing machine is not placed horizontally, resulting in eccentricity of the inner barrel when dehydration, and the washing machine can be adjusted to the level;

2: The clothes are placed unevenly, resulting in eccentricity of the inner bucket when dehydration, and the clothes can be placed evenly, and it may take several more tries to do;

3: The elasticity of the hanging spring of the hanging outer barrel changes, resulting in inconsistent suspension force, the vibration can not be slowed down when dehydration, and a little eccentricity will also make the inner barrel shake, and the suspension spring needs to be replaced if it is solved;

4: The balance fluid in the dehydration balance ring in the upper part of the inner barrel leaks, contact the after-sales supplement for replacement.

Thank you for your interest.

You are welcome to ask the company questions again.

We wish you a happy work life

The fulcrum of the washing machine is not stable and not at the horizontal point, adjust the stable level; The tension of the hanging tie rod of the inner barrel is uneven, and the force of the four tie rods is adjusted to be uniform; The washed items clump off the center of gravity and break up and re-operate the dewatering program.

The fully automatic washing machine can be washed without dehydration.

1: If it is not closed properly or the switch of the top cover is damaged, it may also be that the switch is in poor contact.

2: The washing machine drainage system is blocked or the drain valve is broken, and the washing machine cannot enter the dehydration program.

3: The drain valve does not open the clutch conversion, and its solenoid valve is damaged and defective, which will also make the dehydration unable to operate normally.

4: Poor motor performance and capacitance problems, resulting in insufficient output power. Dress up.

5: The curing program is damaged and cannot enter the dehydration program.

6: The tightening screws of the inner barrel of the washing machine are loose, or the bottom bracket of the inner barrel of the washing machine is damaged.

7: The washing and dehydration of the fully automatic automatic washing machine is completed by the gear at the bottom of the conversion of the solenoid valve, and the damage of the solenoid valve will also make the dehydration unable to operate normally.

Check that the door of the washing machine is closed properly, and then check that the power is on.

Haier washing machine washing, dehydration is normal, but the water does not stop?

Hello happy to answer this question for you, 1The problem is mostly in the water level detection switch, due to the contact oxidation, dirt or ablation caused by poor contact and can not turn on the power supply, resulting in more than water ingress, at this time the water level switch should be overhauled or replaced. 2.

If the pressure pipe is worn and broken due to a long period of use, or the pressure pipe is in poor contact with the water level switch and the outer barrel air nozzle or disengaged, causing air leakage, it can also lead to water ingress, because the computer board is not under pressure and the water level switch does not work. 3.Due to the use of a long time, there is a foreign body blocking the mouth of the air valve, resulting in the pressure can not be transmitted to the pressure switch, at this time the big nut should be unscrewed, and then take out the inner barrel to take out the foreign body blocking the air valve.

4.The inlet valve spool is stuck, resulting in the inability to reset, resulting in the washing machine being flooded, and the inlet valve should be overhauled or replaced.

Haier washing machine washing, dehydration is normal, but the water does not stop?

1. The water level sensor is damaged, if the water level sensor is damaged, when the water in the washing machine reaches the water level, the system cannot correctly perceive the water level, which will cause the washing machine to be flooded all the time. At this point, the washing machine should display F1, indicating that the water level sensor is faulty. 2. The water level switch is faulty, if there is a problem with the water level switch, it can not be closed normally, when the water level is reached, the system will control the water level switch to stop the water intake, if the water level does not stop, it may be a problem with the water level switch, it is recommended to replace the water level switch.

3. No matter what kind of situation you need to repair, it is best to find after-sales personnel for maintenance in time, the general washing machine warranty is 1 year, and the main parts are guaranteed for 3 years, do not dismantle it yourself.

Hello, if the Haier drum washing machine does not stop dehydrating at one time, the hall may be caused by the following reasons:1Washing machine failure:

There may be a malfunction in the washing machine, which prevents the spinning procedure from ending properly. In this case, it is recommended that you contact a professional maintenance personnel for maintenance. 2.

The washing machine is overloaded: If the washing machine is overloaded, it may cause the dehydration program to not end properly. It is recommended that you reduce the load on the washing machine or spin the laundry in batches.

3.Faulty Washing Machine Control Panel: If the washing machine control panel is faulty, it may cause the spinning process to not end properly.

In this case, we recommend that you check whether the control panel is working properly or replace it. If you encounter the situation that the Haier drum washing machine does not stop dehydrating at one time, you can try the following methods of Sun Ji:1

Press the stop button: Try pressing the stop button on the washing machine to see if you can stop the dehydration program. 2.

Restart after power failure: Try powering off the washing machine, wait a few minutes, and then plug it back in to see if that resolves the issue. 3.

Contact after-sales service: If none of the above methods can solve the problem, it is recommended that you contact Haier's after-sales service center for professional repair help. It should be noted that in order to ensure the normal use and safety of the washing machine, it is recommended that you read the instruction manual carefully before using the washing machine and follow the operation steps on the manual.

There are many reasons for the original hunger: 1. Foreign bodies are wound at the bottom of the outer wall of the dehydration bucket. 2. Capacitor failure.

3. The shaft sleeve and shaft of the dehydration motor are locked. 4. The dehydration motor fails, and the coil is abandoned or broken. Suggested Treatment:

1. When dehydrating, some people will put socks, handkerchiefs and other small clothes on top of the clothes, at this time, when the dehydration bucket rotates at high speed, the small clothes will be firmly thrown into the bottom of the outer wall of the dehydration bucket between the top of the dehydration bucket and the end cover, and then tightly wound on the shaft between the bottom Fengzhixiang and the water seal, so that the motor can not run, resulting in dehydration, so it is recommended not to put the smaller clothes into the washing machine for cleaning. 2. After the power supply of the washing machine, the motor of the dehydration bucket makes a "buzzing" sound without rotating, at this time, you can unplug the power plug, check whether the capacitor is invalid, or replace it with a new product; If the motor starts and runs normally, it means that the fault is on the capacitor and a new capacitor needs to be replaced. 3. After the washing machine is powered on, if there is friction between the silver bowl and the tablet, it will also make the motor of the dehydration bucket sluggish or unable to operate.

At this time, the shaft failure needs to be taken out and repaired, and the fault can be swept away after re-installation. 4. Failure of the dehydration motor of the washing machine such as coil discarding and disconnection will lead to the failure of normal operation. The damage of the motor coil is mainly caused by moisture, mostly caused by the destruction of the water sealing bowl or the serious wear of the shaft sleeve, which causes water to leak into the motor coil.

This fault must be checked for the water seal, if the invention of the water seal is damaged or the water seal shaft is seriously worn, the faulty parts should be replaced.

Summary. 5. The drainage screen at the bottom of the laundry bucket contains too many stains and blocks the drainage holes, so the stains on the drainage screen can be removed at this time to dredge the drainage holes. 6. If in the dehydration state, only the wave wheel rotates and the inner barrel does not roll, at this time, it should be checked whether the traction 3 has separated the pawl and ratchet wheel of the clutch.

7. If not, it may be that the adjusting rod nut on the drain valve is loose and worn, resulting in insufficient opening interval. 8. At this time, the interval of the adjusting rod should be readjusted so that the pawl and ratchet of the clutch can be separated. 9. Because of long-term use or divergent use, the drainage hole is distorted and deformed and the drainage is affected, which should be repaired or replaced.

Kiss! Hello! Glad to serve you! The question is coming, please wait patiently for 2 minutes, you are in the whole line of brothers, I will answer for you immediately, and please do not end the consultation carefully!

1. First check the safety switch, and the washing machine is turned on and the program is adjusted to the dehydration state. 2. Press the safety switch brake arm to the lowest with hands or tools, and the tension spring on the drain valve to control the tension of the tension belt loses its elasticity. 3. The drainage hole can not be fully opened, and the adjustable pull belt is shorter, so that the drainage hole can be completely opened.

4. If the brake arm of the safety switch can be dehydrated normally after pressing it by hand or smart stool tool, it means that the power-off interval of the safety switch is low, and the safety switch should be replaced at this time.

5. The drainage screen at the bottom of the laundry bucket contains too many stains and blocks the drainage holes. 6. If in the dehydration state, only the wave wheel turns and the inner barrel is not rolled, at this time, it should be checked whether the traction 3 has separated the pawl of the clutch and the ratchet of the potato returnant. 7. If not, it may be that the adjusting rod nut on the drain valve is loose and worn, resulting in insufficient opening interval.

8. At this time, the interval of the adjusting rod should be readjusted so that the pawl and ratchet of the clutch can be separated. 9. Because of long-term use or divergent use, the drainage hole is distorted and deformed and affects the drainage, which should be repaired or replaced.

Hope mine is helpful to you!