Can the bracelet be blackened and returned? How to remedy it

Straight to the hand, right?

First find a cheesecloth glove Wupan (rub hard), rub it and put it in a sealed bag, and rub it for a few days to see if you can see it. When you see the light, it lasts, and you can come back. But it certainly won't be as good as it was at the beginning.

If there is too much oil sludge on the outside and the above method cannot come out, cover it with a hot towel for a while, then rub it vigorously with a thick glove, and then dry it in the shade. This method hurts the beads, and if the material is not oily enough, even if it can be clean, it will be dry forever.

Help! What should I do if the bungai bracelet is black? Master tips to restore your bracelet to its original state.

The bracelet can still be coiled back if it is black. Here are some remedies:

1.You can put the bracelet into the bead bag, directly rub the bracelet, or you can find a thicker cotton towel, and rub the string constantly, you can polish the surface and grind off the black pulp.

2.If the bracelet is particularly black, you can re-polish the bracelet and then play again. When polishing, you must find a professional master, so that the effect will be better.

3.Re-polishing can also remove the dirt on the surface of the bracelet, if there is a lot of dirt on the surface of the bracelet, it is difficult to scrub it clean with a toothbrush, at this time you can re-polish.

4.If the blackening of the bracelet is not very serious, you can continue to use the handpan and re-wrap the previously blackened pulp to form a new pulp, and the color can be restored to the previous color, but when you continue to use the handpan, you must keep your hands clean and dry, so that the formed pulp will not be blackened.

5.You can use a cheesecloth glove to rub hard, put it into a sealed bag after rubbing, continue to rub it after a few days, repeat it a few times, the bracelet will become brighter, and continue to use the glove plate after it becomes brighter, you can change back to the original color, and the cheesecloth gloves can destroy the original pulp and form a new pulp.

6.When the blackening of the bracelet is very serious, it is necessary to clean off the original slurry and play again. Soak the bracelet in hot water for an hour and a half, if the water gets cold halfway, you need to reheat the water, scrub it with a cotton cloth after soaking the water, and then you can play again after it dries.

7.Replace the soft brush that used to brush the hand skewers, wipe them with steel wool balls, brush them all the time, brush them until the bracelet restores its original color, and then play with the hand again, so that it can be re-formed into a pulp, and it is best to keep it for more than half an hour each time you play, and the bracelet can be brightened again after a month.

The above are some ways to remedy the black bracelet plate, which needs to be selected according to the specific situation.

Sooner or later, wood will be oxidized and blackened, which is inevitable.

The difference is that if the beads of sweat have been tarnishing for a long time, the only way to change them is to wear them small enough to remove the black layer from the surface.

The final state of the normal play beads is basically black and bright.

We all know that the new hand-picked small leaf red sandalwood bracelet, without the formation of pulp, after getting the hand with a cotton cloth for rubbing, there will be red traces on the cotton cloth, this is what we often say that the small leaf red sandalwood color fading phenomenon, this is a very normal phenomenon, and it is also commonly used to identify the authenticity of the small leaf red sandalwood bracelet. The reason is mainly due to the mahogany pigment of the small-leaved red sandalwood logs, which dissolves after encountering water or alcohol, dyes red, and the color of the logs is still red after drying. So when does the small leaf red sandalwood bracelet not fade, there are two situations.

1. When the small leaf red sandalwood bracelet is played for a period of time, the color becomes darker, the hole of the cow hair tube begins to be filled by the slurry, the surface will gradually become very translucent, very fluorescent, and a thin layer of slurry is formed on the surface. Second, I often see some small leaf red sandalwood bracelets that are just enough to buy back do not fade, why is this, and the reasons are as follows:

1.It may be that the surface of these small leaf red sandalwood bracelets has been waxed or varnished, so they will not fade when playing;

2.Or the freshly bought small-leaf red sandalwood bracelet has been placed for a period of time, and the surface and air have a high degree of oxidation or have been naturally oxidized to form a pulp, so it is not easy or less likely to fade;

3.Of course, the possibility of counterfeit small leaf red sandalwood bracelets cannot be ruled out; However, you don't have to be too nervous when you encounter this kind of small leaf red sandalwood bracelet that is just enough to buy back, and you don't have to be too nervous, just think that what you bought is a fake, in fact, it is possible that it will not fade.

The red sandalwood bracelet plate is a little black and buried too, not very serious, you can use a bath towel or burlap to wipe a few times, see if you can wipe the rake, the oiled bracelet can not be cured by what method, can only be polished from the new, but the hand oil and sweat can also be wiped with 1000 mesh sandpaper, in the 2000 mesh polished,

That's that you probably won't be able to cross bracelets.

Just bought the bracelet do not first on the handpan, it is best to use the white cotton glove plate for labor protection, about a week after the bracelet has a certain brightness, turn to the handpan, remember not to sweat on the hands, because the wooden bracelet will rise when damp, and the wood grain will be thick or even cracked after drying. It is best when the hand feels slippery but not astringent when playing, once it is astringent, it means that the hand is sweaty, and there is no need to plate again. Otherwise, the more it is dished, the more dull it will be.

If the bracelet is accidentally wet, it should be dried immediately and then played with white cotton gloves for a few days, and must not be exposed to the sun or air-dried. In addition, bead friends with sweaty hands often turn the bracelet black but dull, which is due to sweat. The solution is to wear the bracelet on the wrist and slide it around the other arm (when wearing short sleeves in the summer) to make the bracelet shine.

If you cook it for a year or two, the bracelet can produce a relatively stable pulp, especially the red sandalwood, huanghuali, and the bracelet of golden silk nanmu will have a glass luster, which is very beautiful

Oxidized, vulgar dust slurry, it's that simple.

Why is it black? The reasons for this phenomenon are as follows:

1. On rainy days, forget to get wet from the rain; I forgot to pick it up after washing and brushing the dishes. Rain or tap water soak the surface of the red sandalwood bracelet in water.

2. The weather is too hot, and you forget to wipe your sweat when you play with your handpan; Wear a bracelet to exercise, and before you know it, the bracelet is stained with sweat ......In addition to water, there are also stolen goods such as human body grease in this sweat, which are attached to the surface of the bracelet.

3. The price of the bracelet is not high, thinking that the oiliness is not so good, and it happens that there are friends around me who have oiled the bracelet, so I want to "moisturize" my bracelet. As a result, a few days after the "moisturizing", the bracelet looked quite shiny, but after a week, it became darker and darker, and it was still greasy.

As a reminder, too much oil can clog the pores of the wood, and even make the beads black, with a greasy feel.

What to do if the small leaf red sandalwood plate is black.

Situation 1: The bracelet has initially "turned black" and has not completely become a "black briquette".

At this time, your bracelet should only be a preliminary sign of "broken", not completely "broken", you can wear white cotton gloves, or use the thick cotton side of the bath towel, a little harder when playing, and remove those "dirty" in the way of playing with the plate. This is a simple and effective way to save the life. But be careful, don't get water, oil, sweat and other things.

Situation 2: The bracelet has completely "turned black", the color has deteriorated, and the luster is gone.

At this time, in addition to the reason for the poor quality of the material itself, the bracelet is basically completely "broken", and the best and most thorough way is to re-polish and polish off the "dirty" layer.

You can use sandpaper to polish yourself, or you can send it to a professional place to polish, polishing also needs to be "piece" polished to the same, if you are worried that you can't do it, let professional people do it.