Ultra simple porcelain punching method, porcelain punching method without electric drill Ultra simpl

1. There is no hand drill, there is a violent and convenient method. First of all, put the container you want to punch into the water and soak it for a while, then find two wet towels and stuff it into the container, turn the container upside down, put it steady, and put a cushion (cloth or foam) at the bottom.

2. Soak in water: It will be better to punch holes in water for a period of time, especially for containers without glaze, and it is better to spend a night or a day.

3. Towel: Try to stuff it as much as possible, which can play a buffering role and avoid breaking the pot directly.

4. Strength: Smash one or two pots to have experience, do not need too much strength, girls smash a few times is enough, pay a little attention to the control of the strength of the small strength of the smash may be easier to maintain the integrity of the hole, too hard is easy to break the pot, at this time you can consider turning the pot into magic.

5. Compared with smashing pots, there is a safer way, which is to use a screwdriver to drill holes directly in the pots, but it will take a lot more effort and time. If you encounter a harder pot, you won't be able to drill it. If the bottom of the pot is not very deep, in fact, control the watering intensity, and there is no problem in planting more succulents.

<> "Optional glass pin penetration glass drill bit, strong impact, and suitable for drilling holes for all ceramic tiles. An optional impact masonry drill is suitable for drilling holes in the tile, which not only drives quickly, but also ensures that the tile does not break.

What drill bits are used to punch holes in porcelain:

1. You can choose a glass drill bit, which has a strong impact and is suitable for punching holes for all ceramic tiles. 2. The impact masonry drill bit can be selected, which is suitable for drilling holes for ceramic tiles, which not only has a fast drilling speed, but also ensures that the tiles are not broken.

Tips, to punch holes in the tiles, you must first determine the position, and then paste the mark with tape. Aim the impact drill bit vertically at the marking point, start the impact hammer, pay attention to the starting force should not be too large, and it is advisable to pass through it slowly.

How to punch holes in the tiles without cracking:

1. Punching position.

First of all, we should think that the tile is not cracked, and it is necessary to choose a good location for punching, usually the joint of the two tiles, or the middle of the tile, and do not choose the edge of the tile, which is easy to crack.

2. Choose the right tool.

When drilling ceramic tiles, it is necessary to choose the corresponding tools, such as glass drill bits or emery drill bits, and do not choose concrete drill bits.

3. Control the speed.

When drilling ceramic tiles, it is necessary to pay attention to the rotation of the drill bit, and the initial stage of the hole should be low-speed, and after the glazed surface of the tile is drilled, the speed should be slowly increased. And when using a percussion drill, turn off the impact function and put it first at low speed.

The tile glaze grinds off a piece, and then punches through the tile layer at high speed.

4. Control the size of brick holes.

When punching holes in tiles, pay attention to the size of the brick holes, and first make a small hole in the tilt. If you want to make a large-diameter hole, you can use a drill to turn out the imprint on the tile, and then use the drill bit to drill around the imprint. In addition, during the drilling process, in order to prevent the drill bit from being too hot, it is recommended to fill the mineral water bottle with water, make a hole in the cap of the bottle, and water it while punching the hole, so that the temperature of the contact part between the drill bit and the tile is reduced.

1. Punch holes at the bottom of the porcelain bowl, you can use a hole punch, add a little water at the bottom of the cup when punching, otherwise the friction temperature is too high, the cup can be soaked in water for a few days before operation, so that it is not easy to break, and the space in the cup should be filled with a towel or newspaper, so that the stress point of the nail is not all at the bottom of the jar.

2. Porcelain is a kind of porcelain stone, kaolin, quartz stone, mullite, etc., and the appearance is glazed or painted. The porcelain is formed by firing at a high temperature (about 1280-1400) in a kiln, and the glaze color on the surface of the porcelain will undergo various chemical changes due to the different temperatures. Sintered porcelain tires generally contain less than 3% iron and are impermeable, and are widely used by people all over the world because of their relatively low cost and wear-resistant and impermeable characteristics.

China is the homeland of porcelain, and porcelain is an important creation of the working people of the Han nationality. The invention of porcelain is the great contribution of the Han nation to world civilization, and in English, "porcelain (China)" is the same word as China (China).