The house is renovated, and the water gate is at home

The main water valve of the current house is generally in the hallway, not in the house. The previous houses were all in their own homes, and the main valves of the heating lines were all the same. However, it is completely possible to install a main valve at the entrance to the house, so that it is convenient for you to close it if you have anything.

Generally speaking, each household has a valve control after the water main pipe enters the house, and can only control the waterway of their own home, otherwise it will be very troublesome to use.

According to different construction requirements, you can set up a tap water main gate at home, and the normal main gate will be set up in the outdoor stairway, because it is easy to repair and switch, and does not affect other structures at home. There is also a main gate at the water meter, which is overhauled with the main gate at home. Therefore, for different decorations, as long as the householder requires it, you can still add a main gate at home, which does not affect your use.

The main water gate, if it is squared, or the self-built house is in your own home, if it is a building, it may be in the corridor, depending on the situation analysis.

You are a house renovated and the main water gate is at home. The preview is to see where you put your own decoration money.

The house is renovated, and the main water gate is at home, right? It's supposed to be at home, it depends on how you design it?

Every few pipes will have a common water valve, and this one is either installed indoors or outdoors not far from your home.

1.If the water valve is indoors, you can go to the kitchen to find it, and generally the water valve is in the corner of the kitchen.

2.If the valve is outdoors, you can look for it downstairs in your house. Each house has a "water valve well" downstairs (rest assured, there is no water or electricity in the water valve well, and the depth is only 50cm, which is very safe. , you can find the water valve well, find the water valve that belongs to your home to operate.

3.I really can't find it, you can find a property or a decoration team.

Nowadays, commercial houses generally have a water meter room in the corridor, which has water meters and valves for several households on the same floor.

If you want to install a main gate in your own home, you will add it to the cabinet when you renovate the water and electricity.

But the main valve of the water in the house is in the house, well, it is near the water pipe into the house.

Yes, but the water inlet pipe has to be opened. It's a bit difficult to hide anyway.

You can go into more detail.

It is a one-household-one-table transformation.

Or is it that the original pipe is outdated, and now it is replaced with a new pipeline.

Your home is not living on the ground floor.

The makeover must go through your home.

Generally speaking, things inside the household.

is property that you legally own.

If the owner does not agree to the construction.

The water company can't force the construction.

However, if the construction is not carried out, it will not affect the water supply of the entire building.

You say be more detailed and I'll give you advice.

Hefei talent decoration company for you to answer: it is recommended to use the way to walk the bright line, the water pipe is recommended to go to the top, after the completion of the use of gypsum line or gypsum ceiling blocking, as for the maintenance of rights and interests, you should find the original decoration of the company or individual, find the original transformation of the water circuit drawings or stubs, as for avoiding ripping.

I originally had one meter per household, because the water meter was indoors, so I said that I had to change the water meter outdoors, and if you didn't change it, I would forcibly stop the water.

Thank you all for your comments.

Your main valve is turned off, and there is no water in the room, and it's very simple because of the next door, House Wings.

Since there is already a household inlet valve in the pipe well, there is no need to install a master valve at home!

The main valve is rare to use when replacing the angle valve and faucet, and it is usually not touched at all, as long as there is it, why not run a few more steps.

You don't need to install it, in the water meter box in the stairwell, there is a valve on the side of the water meter, and then it is the water pipe that enters your home. Having a valve outside the door is enough for emergencies, and if there is no one at home, a neighbor can help close the valve.

Quite important.

First, if there is a water leak in the room, it is more troublesome if there is no weather off.

Second, theoretically, the main switch of the water cannot be installed in the wall, so there is no problem in replacing it.

Important, for example, if one day your bath faucet breaks, do you want to go out and turn off the water in the whole building or do you want to turn it off at home?

Call a plumber and he'll figure it out.

The main switch is very important, cold water. Hot water. It is necessary to have a main gate and be able to close easily in the event of a problem.

You don't have to be okay in this situation, the important thing is that each point should have an angle valve.

It's important to ask a plumber to add one for you at home.

In the case you described, it doesn't matter if you don't do it at home.

Is the master switch made by the developer you are talking about, the master switch that every household has, or the master valve switch that is shared by all residents of the whole building?

If it is shared by everyone, it is better to install a valve at home.

If it is a per-house switch set up by the developer for each household, then there is no need to set a switch in the home.

For example, if you want to go out on vacation, then you have to pull the electric switch to turn off the water valve, which is relatively safe, and can avoid the phenomenon of bursting the water pipe in the house or the switch is not closed tightly, soaking the house. Turning off the valve in your own home will not affect other people's homes, such as changing the faucet.

If the home is finished, the valve is installed outside and inside the water meter, it is also possible, the water meter should not be buried in the wall, at most box into the wall. If you already have it, you don't need to install it.

If the main thing is to prevent the backflow of water from solar energy.

It is recommended to install a check valve on the solar water inlet pipe.

After all, after installing the check valve, it will still eat part of the pressure drop, which means that the water pressure will be a little lower.

This is not necessarily, it is usually like pliers.

It can be installed, you can find the property to close the main valve of your unit door, and then let your original decoration master or find a professional to decorate.

If you want to install a master valve in your home, you have to find the total water intake at home (usually in the kitchen or bathroom) (it should be all bricked) knock the bricks, find the water pipe and install the main valve, and then buy new bricks and paste them. It's a lot of trouble, and there are so many details.