What is the reason why the Chigo water heater does not heat?

What to do if the electric water heater does not heat.

1. There is a problem during installation, one of the two ports of the water heater is for water inlet and one is for water out, under normal circumstances, as long as the water supply is normal, it can be heated, and the speed is very fast, which is also a big advantage of instantaneous type. But if we reverse the connectors at both ends, it will definitely not be heated, even if you heat it for 24 hours, it will have no effect at all. Our solution is also very simple, turn off the water heater, and then switch the water pipes at both ends, you can rest assured that if you accidentally connect the wrong one, the water heater will not be damaged.

2. There is a phenomenon that we don't know if you have noticed, no matter how people in some areas clean their mouths and brush their teeth frequently, their teeth will be black and yellow, and the reason for this phenomenon is that the water quality in each of our regions is different. In fact, the water heater will also be affected by the water quality during use, if there are too many impurities in the local water, after long-term use, the water inlet of the water heater will not be smooth or even directly blocked. Everyone knows that instantaneous electric water heaters are automatically heated by induction, but now the induction device is closed, and the signal that it needs to be heated cannot be received, so it will not be heated automatically.

If you want to solve this kind of problem, you will use the return connection inlet and outlet we mentioned above, let the water flow backwards, and if you can't do it, you can only replace the induction device, and you probably need to move if you want to completely solve this problem.

3. The over-temperature protector fails or your water heater does have an over-temperature phenomenon and you don't notice it. What we have to do is to reset the device to see if it can be heated normally, if it is normal, then it proves that there was an overtemperature before, if it still can't be heated, and it shows an overtemperature, it needs to be replaced.

4. There is a short circuit in your instantaneous electric water heater, to put it bluntly, it is the first leakage, the instantaneous electric water heater has a self-protection device, if this phenomenon occurs, the normal operation can not be carried out, we need to check it, and then repair it.

A few days ago, I also encountered a situation where the instantaneous electric water heater did not heat, and there was no problem when I removed it for inspection, and it was normal to install it again. You can first power off for a few minutes and then try to power on, if it is normal, it is caused by the crash of the control circuit, if it is not good, check whether the water pressure meets the requirements, the low water pressure will protect. If the water pressure is normal, disassemble the machine to check whether the sockets are connected to each other, and whether the control circuit and heater are damaged.

Cause. 1. Heating efficiency is reduced

As we all know, since the service life of electric water heaters is usually about eight years, if it exceeds this age, the wear and tear of the heating rod will be aggravated, that is, the thermal efficiency will be reduced, resulting in the water heater not heating. At this point, the best way to deal with it is to replace it with a new water heater.

2. Increased scale:

I believe that friends who have used storage electric water heaters know that a large amount of dirt will be attached to the heating rod, which will cause the heating time of the water heater to become longer. At this point, you need to do a thorough cleaning of your water heater. Normally, the liner needs to be cleaned once every 2 years or so.

3. The preset temperature of the thermostat is low

This phenomenon usually occurs when the water heater is used or cleaned for the first time, especially after the change of seasons, because the temperature inside the thermostat does not meet the requirements for use, so it cannot be heated, at this time you should turn the preset temperature up.

The Chigo water heater is not heated when it is powered on, and it may be caused by the internal circuit being open, the temperature adjustment setting is improper, and the heating pipe is damaged. A water heater is a device that turns the temperature of cold water into hot water in a certain period of time through various physical principles. According to different principles, it can be divided into electric water heaters, gas water heaters, solar water heaters, magnetic energy water heaters, air energy water heaters, heating water heaters, etc.

Manufacture of air-conditioning part and manufacture of hot water section.

1.Open the water outlet mixing valve for hot water to the maximum end of the hot water (do not mix with cold water).

2.The angle valve of the hot water line is opened to the maximum.

3.The tap water pressure is too low. Avoid peak periods.

4.In the water heater control panel, set the appropriate sanitary hot water temperature, which is usually available in the range of 30-60.

I have also thought about this issue carefully and have been thinking about it day and night. Then, under this difficult choice, I thought about it and couldn't sleep well. In this case, as far as I am concerned, I'm sorry, but the significance of my mistake to me cannot but be said to be very significant.

It may be caused by the damage of the relay of the motherboard, not engaging or the open circuit of the electric heating pipe, this phenomenon can only be caused by finding the key point of the problem, and repairing or replacing it.

After the electric water heater is plugged in, the indication does not light up and does not heat for the following reasons: External faults: 1. Check whether the electric water heater socket at home has a 220V voltage. 2. Whether the power supply at home has tripped, and whether the power cord has been checked firmly.

Chigo water heater is good.

1. Its biggest feature is that it is very cheap, much cheaper than some traditional brands, which is the main reason why many people like Chigo water heaters.

2. Although it is cheap, the safety is not bad, there is a built-in anti-electric wall design, the function of the ground wire with an electric alarm, and the waterproof effect of IPX4, there is no need to worry about the safety of electricity when using it, which solves the problem that many people are worried that the leakage of the electric water heater will be very dangerous.

3. In addition, it also has a larger capacity, faster heating speed, and more energy-saving energy-saving mode, with a long service life, no hot and cold, and no water in the middle of the bath. Its 3D heat lock technology allows the water heater to maintain a good water temperature even if the power is off for 72 hours.

4. Due to the 2000 watts of high-power heating shed, it can be heated quickly in a short time, the surface layer is not easy to scale, the heating tube is a three-layer design, the outermost layer is chain Li Hong stainless steel, the second layer is the insulation layer, the third layer is the resistance wire, the three-dimensional heating technology makes the hot water output very fast.

Summary. How to use Chigo water heater: After the gas water heater is installed, you only need to open each valve, and the water heater will work automatically as soon as you turn on the hot water faucet.

How to use the water heater of Zhigao Banquet: After the old gas hot water device is installed, you only need to open each valve, and the water heater will work automatically as soon as you turn on the hot water.

1. Open the water inlet valve and faucet, plug in the power supply, and press the switch button of the water heater. 2. Set the water temperature. 3. After the water is boiled, adjust the valve to the middle position first, and test the water temperature to be suitable before use.

4. After using the water heater, turn off the switch on the electric water heater first, and then unplug the power supply after the hands are dry.

I tried, no, L5 keeps displaying, press the power button, and then click the plus sign to adjust the water temperature.

You open the water inlet valve, and after the water is in, you can adjust the temperature.

Chigo electric water heater is of good quality, focusing on sterilization and constant temperature washing, UV sterilization through 5-fold filtration, better water quality, and also equipped with security function, safety and no hidden dangers

At the same time, it also has the functions of steady flow and constant temperature, automatic temperature adjustment, etc., for children in the family, it is recommended to choose this, this temperature control method is double adjustment of water and gas, and the material of the water tank is oxygen-free copper.

Prepare the installation tool first:

Electric drills, electrical pens, electrical tapes, rulers, awls, nozzle pliers, wrenches, etc. The installation steps of the electric water heater are to check the safety of the meter and the total switch safety, check the wire diameter of the incoming wire, check whether the air switch of the water heater matches the water heater, and check whether the wire diameter of the water heater matches the water heater.

Install the water inlet switch; And check whether there is any leakage in the water pipe or whether there are other sundries in the pipe, unpack the water heater, check the completeness and integrity of the water heater and accessories, and install the electric water heater according to the size of the screw hole and the size of the lifting rod of the water heater hanging plate.

Use a pencil to set the position on the wall first, the screw hole positioning should avoid the circuit and waterway in the wall, drill holes in the wall to install the expansion plug, install the water heater hanging plate Electric water heater installation steps, install the water heater on the hanging board, and install the shower lifting bracket.

Connect the inlet pipe and outlet pipe and the power cord and ground wire electric water heater installation steps, turn on the power supply and water heater switch, test whether the water heater is working properly, electric water heater installation steps, electric water heater installation is completed The installation steps of the electric water heater are introduced here, you can follow these steps to do.

The worst water heater after-sales are all paid, and they break when they are just bought, and the customer service allows you to collapse.

Hello dear, I am happy to answer for you, dear hello, the reason why the Chigo instantaneous water heater does not enter the water: 1. Check the setting of your water heater, this situation is more, many users adjust the temperature when using the electric water heater, or do not adjust it, so that there will be no hot water at all. 2. Whether the power display of the electric water heater is bright, if not, it may be a problem with the temperature control device.

3. There is also the problem of thermostat tripping, generally good electric water heaters have dual thermostats, that is, room temperature control and over-temperature temperature control, these two kinds of temperature control are a kind of control of your water heater water temperature display and control, one is to avoid room temperature temperature control problems, for you to trip. That is, double insurance, some of them will directly lead to the inability to boil hot water because of temperature control tripping. Calling a professional to turn on the machine quickly got it done.

4. There is also to see whether the hot water pipe is blocked (or the water is stopped), and the water stop will directly cause the water heater to be unusable, because the principle of the electric water heater is that the cold water runs against the hot water, and see if the water inlet of the water heater is blocked. If I am helpful to you, you can give me a thumbs up at the end of the consultation and wish you all the best.